2022 SUZUKI JIMNY 100

INS.PECTION AND MAINTENANCE
4-tyre rotation
65D459
To avoid uneven wear of your tyres and to prolong their life, rotate the tyres as illus­trated. Tyres should be rotated every 10000 km (6000 miles). After rotation, adjust front and rear tyre pressures to the specification listed on your vehicle's Tyre Information Label.
6-39
Changing Wheels
78RB07014
To change a wheel, use the following pro­cedure:
1) Remove the jack, tools and spare wheel from the vehicle.
NOTE: How to remove the spare wheel:
78RB07052
1. Remove the center nut (1 ), then remove the spare wheel half cover (2) (if equipped). 2. Remove the wheel nuts of the spare wheel, then remove the spare wheel with both hands.
2) Loosen, but do not remove the wheel nuts. 3) Jack up the vehicle (follow the jacking instructions in the "EMERGENCY SER­VICE" section in this manual) 4) Remove the wheel nuts and wheel. 5) Before installing the new wheel, clean any mud or dirt off from the surface of the wheel and hub with a clean cloth. Clean the hub carefully; it may be hot from driving.

6) Install the new wheel and replace the wheel nuts with their cone shaped end facing the wheel. Tighten each nut snugly by hand until the wheel is securely seated on the hub.
78RB07017
Tightening torque for wheel nut: 100 Nm (10.0 kg-m, 72.3 lb-ft)
7) Lower the jack and fully tighten the nuts in a crisscross fashion with a wrench as shown in the illustration.
A WARNING
Use genuine wheel nuts and tighten them to the specified torque as soon as possible after changing wheels. Incorrect wheel nuts or improperly tightened wheel nuts may come loose or fall off, which can result in an accident. If you do not have a torque wrench, have the wheel nut torque checked by a SUZUKI dealer.
INSPECTION AND MAINTENANCE
NOTE: How to install the spare wheel:
(3)
78RB07053
When you install a 195/B0R 15 spare wheel to the vehicle, set the spare tyre bracket (3) (if equipped) with the mark of "195" on up posi­tion, and handle it in the reverse order of removal. For vehicles equipped with the spare wheel half cover; when you install the spare wheel half cover, check that the hollow (4) of the cover is positioned below the center of the spare wheel half cover.
6-40

INSPECTION AND MAINTENANCE
Fuses in engine compartment
(1) Main fuse box (2) Relay box
Main fuse box
~I'----,
6-43
§]
§]
§]
0
[N]
78RB07021
78RB07022
Relay box
00illJ[@[]~ [£C][@[]~(30) [@[]Dill]
0~'12217a ~ ~(31} ~[@[]Dill]
~[@[]~ !Jill] Dill]
~ ~ [@[] [illiJ 8 ;~ ~(32) cc
!ril @DB ~z v (33) :~ ~ ~ FRONT ~
78RB07023
MAIN FUSE / PRIMARY FUSE
(1) 120A FL 1
(2) 100A FL2
(3) BOA FL3
(4) 100A FL4
(5) 50A FL5
(6) 50A Ignition switch
(7) 40A ABS motor
(8) -Blank
(9) 30A Blower fan
(10) 30A Starter motor
(11) 30A Headlight cleaner
(12) 15A Headlight (Right)
(13) 15A Headlight (Left)
(14) 25A ABS/ESP® control mod-ule
(15) -Blank
(16) 15A Ignition coil
(17) 25A Headlight high
(18) 30A Back up
(19) -Blank
(20) 15A Fuel injection

NOTICE
Never apply a garage jack to the exhaust pipe, front fender splash guard, side sill splash, rear fender splash guard, front differential or rear differential.
NOTE: For more details, contact a SUZUKI dealer.
Changing wheels
To change a wheel, use the following pro­
cedure: 1) Prepare the jack, tools and spare tyre. 2) Loosen, but do not remove the wheel nuts. 3) Jack up the vehicle (follow the jacking instructions in this section).
A WARNING
Shift into "P" (Park) for an automatic transmission, or into 11R" (Reverse) for a manual transmission vehicle when you jack up the vehicle. Never jack up the vehicle with the transmission in "N" (Neutral). OthR erwise, unstable jack may cause an accident.
4) Remove the wheel nuts and wheel.
65J4033
5) Clean any mud or dirt off from the sur­face of the wheel (1 ), hub (2), thread part (3) and surface of the wheel nuts (4) with a clean cloth. Clean the hub carefully; it may be hot from driving.
EMERGENCY SERVICE
6) Install the new wheel and replace the wheel nuts with their cone shaped end facing the wheel. Tighten each nut snugly by hand until the wheel is securely seated on the hub.
78RB08003
Tightening torque for wheel nut 100 Nm (10.0 kg-m, 72.3 lb-ft)
7) Lower the jack and fully tighten the nuts with a wheel wrench in numerical order as shown in the illustration.
7-4

SPECIFICATION
Vehicle identification
Chassis serial number
78RB10001
9-1
for some vehicles)
00000
78RB10003
The chassis and/or engine serial numbers are used to register the vehicle. They are also used to assist a SUZUKI dealer when ordering or referring to special service information. Whenever you have occasion to consult a SUZUKI dealer, remember to identify your vehicle with this number. Should you find the number difficult to read, you will also find it on the identifica­
tion plate.
Engine serial number
78RB10004
The engine serial number is stamped on the cylinder block as shown in the illustra­tion.

SUPPLEMENT
For Australia
Built date
Built date is located on Vehicle Identifica­tion plate. "Built date" means -the calendar month and the year in which the body shell and power train sub-assemblies are conjoined and the vehicle is driven or moved from the production line.
Child restraint
A WARNING
Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circum­stances are they to be used for adult seat belts, harnesses or for attaching other items or equipment to the vehi­cle.
10-1
Installation of child restraint with
top tether anchorage
Some child restraint systems require the use of a top tether strap. Top tether anchorage brackets are provided in your vehicle at the locations shown in the illus­tration. The number of the top tether anchorage brackets provided in your vehi­cle depends on the vehicle specification.
(1)
(1) Anchor fitting
78RB10005
1) Remove the luggage box (1 ). 2) Secure the child restraint on the rear seat using the procedure described above for securing a restraint system that does not require a top tether strap. 3) Hook the top tether strap to the top tether anchorage bracket and tighten the top tether strap according to the instructions provided by the child restraint system manufacturer. Attach 54Gm the top tether strap to the correspond­ing top tether anchorage bracket located on the floor of the rear cargo area.

PANTOGRAPH JACK
INSTRUCTION MANUAL
CE
Manufacturers:
RIKENKAKI CO., LTD. 5-6-12 Chiyoda, Sakado-shl, Saitama, 350-0214 Japan Tel: 049-248-1661 Fax:049-284-4340
CHANGZHOU RIKENSEIKO MACHINERY CO., LTD. No.5 Xinlin Road. Zhonglou Changzho1.1, JiangsLJ CHINA Te!: 0519-327-5284 Fax:0519-327-0811
Please read this INSTRUCTION MANUAL before operation!
Norm: EN 1494:2000+A1:2008
Attention and warning -The JACK may be used only for replacing tyres, not for any other purpose. -Use the JACK no more than 50 times. -No-loadlng person. • Never get under vehicle raised by Jack. -Use of defective or Inadequately ma!ntalned jacks Is extremely dangerous.
Meaning of pictogram on caution label
Parts name of Pantograph Jack
FJG1
Technical Data and Application
'
This symbol Indicates a potential hazard that could result In death or serious Injury.
This symbol Indicates you never get under the vehicle when it Is supported by the Jack.
A ; TOPHOLDER B : BASE C: UPPER ARM D :LOWER ARM E : HANDLE JOINT F :JACKSCREW G : NOMINAL LOAD (t)
lL. H, H3 H,
H1: MINIMUM HEIGHT(mm) H2; MAXIMUM HEIGHT (mm) HJ: PERFORMANCE ASSURANCE HEIGHT (mm) X : JACK HEIGHT (mm) Y: LOAD(t) M: MODEL T :TYPE
M T G H, H, H, 55L Suzuki Tupe-I 0.95 89 327 208 72K Suzuki Tvoe-II 0.95 70 281 175.5 54L Suzuki Type-III 0.95 80 318 199 81A Suzuki Type-IV 1.0 85.5 344 214.75 77K Suzuki Type-V 1.25 100.8 436.3 268.55
FIG2