INSPECTION AND MAINTENANCE
Bulb replacement
_A CAUTION
Light bulbs can be hot enough to burn your finger right after turning off lights. This is true especially for halogen headlight bulbs. Replace the bulbs after they become cool enough.
The headlight bulbs are filled with pressurized halogen gas. They can burst and injure you if they are hit or dropped. Handle them carefully. To avoid injury by sharp-edged parts of the body, wear gloves and a long-sleeved shirt when replacing light bulbs.
NOTICE
The oils from your skin may cause a halogen bulb to overheat and burst when the lights are on. Grasp a new bulb with a clean cloth.
NOTICE
Frequent bulb replacement indicates the need for an inspection of the electrical system. This should be carried out by a SUZUKI dealer.
6-47
Headlights
LED type
Since special procedures are required, it is recommended that you take your vehicle to a SUZUKI dealer for light replacement.
Halogen type
78RB07025
(1) Bulb
8~'",,,
""
'\:~
(3) ~f I r-,.t:: l'1
Jlilt10or\01 ~o
"-" [l!l ,Q
78RB07026
1) Open the engine hood while the engine is stopped. Disconnect the coupler (2). Remove the sealing rubber (3) by pulling the grip (4).
78RB07027
2) Push the retaining spring (5) forward and unhook it. Then remove the bulb. Install a new bulb in the reverse order of removal.
78R808004
3) Connect jump leads as follows:
1. Connect one end of the first jump lead to the positive (+) terminal of the discharged battery (1 ). 2. Connect the other end to the positive (+) terminal of the booster battery (2). 3. Connect one end of the second jump lead to the negative (-) terminal of the booster battery (2).
4. Make the final connection to an unpainted metal part (3) of engine cylinder head in the vehicle with the discharged battery (1 ).
A WARNING
Never connect the jump lead directly to the negative (-) terminal of the discharged battery, or an explosion may occur.
4) If the booster battery you are using is fitted to another vehicle, start the engine of the vehicle with the booster battery. Run the engine at moderate speed. 5) Start the engine of the vehicle with the discharged battery. 6) Remove the jump leads in the exact reverse order in which you connected them.
EMERGENCY SERVICE
Towing your vehicle
(recreational towing)
If you need to have your vehicle towed, contact a professional service. A SUZUKI dealer can provide you with detailed towing instructions.
A WARNING
When you tow your vehicle, follow the instructions below to avoid accidents and damage to your vehicle. In addition, be sure to observe government and local requirements regarding vehicle lighting and trailer hitches or tow bars.
7-6
No.Using Conditions • When temperature under -40-C . • On miring or sand ground . • On big gradient road . • In extreme nature condition: rainstorm, typhoon, cyclone, snowstorm, thunder•storm. etc . • Loading dangerous heavy, for instance: melted metal. acidity substance, radioactivity substance or specially crisp goods • • Contact with hood directly . • Using on boat. • The ground with difference in level.
Operation Instructions Whenever a wheel is changed, always remove any corrosion that may be present on inside of wheel and wheel mounting surface on vehicle. Details: Please operate according to the "operation instructions", Operate the jack on the level ground while checking the jack and the load. Musln"I operate under raising load, unless the load is fastened surely . • Park the car on the nat, love ground and apply the brake firmly. • Set transmission in "reverse"(automalic transmission in ·park") . • Turn on the hazard warning Hasher . • Remove jacklng tools and spare tire from stowage area . • Block fFont and rear of wheel diagonally opposlte wheel being removed before operating jack .
~
ITT
~ .s,.Cl(Jf>Of'(llITT J-'CKIW
~ • Loosen, but do not remove wheel nuts by turning wrench counter clockwise • • Raise jack until Jack-head groove fits boss or frame see Illustrations . • Operate jack with slow, smooth motion, using Jack handle . • Raise vehicle so an innated lire will just clear surface, remove nuts and wheel. • Install wheel, then slightly tighten each nut, wheel must be seated on hub . • lower vehicle, and fully tighten wheel nuts In across-cross sequence by turning wrench clockwise.
Maintenance • Please prevent the JACK SCREW from accretion of dirt . • Check the nameplate, keep the shape same as original. • No-re jigger the Jack's construction privately . • After any use, consult immediately your Suzuki Dealer or Service Partner for inspection and maintenance of the jack . • If the label (slicker) is damaged, pt ease consult your Suzuki Dealer or Service Partner.
