2022 SUZUKI GRAND VITARA counter

7-28
INSPECTION AND MAINTENANCE
54P00-01E
If the coolant level is below “LOW” mark,
more coolant should be added. When the
engine is cool, remove the degassing tank
cap by turning it counterclockwise slowly to
release any pressure. And add coolant
until the degassing tank level reaches
“FULL” mark. Never fill the degassing tank
above “FULL” mark.
Coolant replacement
Since special procedures are required, ask
your authorized SUZUKI dealer for this job.
Air cleaner
If the air cleaner is clogged with dust, there
will be greater intake resistance, resulting
in decreased power output and increased
fuel consumption.
(For gasoline engine model)
61MM0B063
1) Remove the air cleaner inlet hose (1).
2) Remove the bolts (2), loosen the bolt
(3) and lift the air cleaner case (4)
directly above.
61MM0B064
3) Unclamp the side clamps, and remove
the element from the air cleaner case. If
it appears to be dirty, replace it with a
new one.
4) Clamp the side clamps or tighten the
bolts securely.
WA R N I N G
It is hazardous to remove the reser-
voir tank cap (degassing tank cap) for
a diesel engine when the water tem-
perature is high, because scalding
fluid and steam may be blown out
under pressure. Wait until the coolant
temperature has lowered before
removing the cap.
NOTICE
When lifting the air cleaner, check that
the air cleaner does not interfere with
the engine oil dipstick (5) to avoid
damage the dipstick.
(4)(5)
(1) (2)
(3)

7-45
INSPECTION AND MAINTENANCE
54P00-01E
Bulb replacementHeadlights
54P000709
(1) Headlight (high beam)
(2) Headlight (low beam) (if equipped)
80JM071
Open the engine hood. Disconnect the
coupler by pushing the lock release. Turn
the bulb holder counterclockwise and
remove it.
CAUTION
• Light bulbs can be hot enough to
burn your finger right after turning
off lights. This is true especially for
halogen headlight bulbs. Replace
the bulbs after they become cool
enough.
• The headlight bulbs are filled with
pressurized halogen gas. They can
burst and injure you if they are hit
or dropped. Handle them carefully.
• To avoid injury by sharp-edged
parts of the body, wear gloves and
a long-sleeved shirt when replacing
light bulbs.
NOTICE
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.
NOTICE
Frequent bulb replacement indicates
the need for an inspection of the elec-
trical system. This should be carried
out by your SUZUKI dealer.
(1) (2)
EXAMPLE

7-46
INSPECTION AND MAINTENANCE
54P00-01E
Side turn signal light (if equipped)
64J195
Since the bulb is built-in type, replace it as
the light assembly. Remove the light
assembly by sliding the light housing left-
ward with your finger.
Front turn signal light and front position light
54P000710
(1) Front turn signal light
(2) Front position light
54P000711
1) Open the engine hood. To remove the
bulb holder of the front turn signal light
(1) or the front position light (2) from the
light housing, turn the holder counter-
clockwise and pull it out.
(1)(2)
(1) (2)

7-47
INSPECTION AND MAINTENANCE
54P00-01E
61MM0B078
(3) Removal
(4) Installation
2) To remove the bulb of the front turn sig-
nal light (1) from the bulb holder, push
in the bulb and turn it counterclockwise.
To install a new bulb, push it in and turn
it clockwise.
To remove and install the bulb of the
front position light (2), simply pull out or
push in the bulb.
Front fog light (if equipped)
1) Start the engine. Turn the steering
wheel to the opposite side of the fog
light to be replaced to replace the bulb
easily. Then turn off the engine.
54P000732
2) Remove the screws (1).
54P000712
3) Remove the clips (2) by prying them off
with a flat-bladed screwdriver as shown
in the illustration.
(2)
(1) (3)
(4)
EXAMPLE
(1)
EXAMPLE
(2)
EXAMPLE

7-51
INSPECTION AND MAINTENANCE
54P00-01E
54P000720
3) To remove the bulb holder of the rear
turn signal light (5) or the tail/brake light
(6) from the light housing, turn the
holder counterclockwise and pull it out.
54P000721
(7) Removal
(8) Installation
4) To remove the bulb of the rear turn sig-
nal light (5) or the tail/brake light (6)
from bulb holder, push in the bulb and
turn it counterclockwise. To install a
new bulb, push it in and turn it clock-
wise.
54P000722
NOTE:
When reinstalling the light housing, check
that the clips are properly attached.
(5)
(6)
(7)
(8)(5) / (6)
EXAMPLE

7-52
INSPECTION AND MAINTENANCE
54P00-01E
Reversing light
54P000723
1) Open the tailgate. Remove 15 clips (1),
and then pull out the trim (2).
54P000724
2) Disconnect the coupler (3) by pushing
the lock release. Turn the bulb holder of
the reversing light (4) counterclockwise
and remove it.
61MM0B090
(5) Removal
(6) Installation
3) To remove and install the bulb of the
reversing light (4), simply pull out or
push in the bulb.
License plate light
61MM0B086
1) Turn the cover (1) counterclockwise to
remove it.
(1)
(2)
(3)(4)
(4)
(5)
(6)
EXAMPLE
(1)

7-53
INSPECTION AND MAINTENANCE
54P00-01E
61MM0B087
2) To remove and install the bulb of the
license plate light (2), simply pull out or
push in the bulb.
Rear fog light (if equipped)
54P000725
1) Insert your hands from the back side of
the rear bumper. Remove 2 nuts (2)
that fix the light housing (1) in place.
54P000726
2) Remove the light housing (1) by push-
ing the bolts (3). To remove the bulb
holder of the rear fog light (4), turn the
holder counterclockwise and pull it out.
(2)
(2) (1)
(1) (4) (3)(3)

7-54
INSPECTION AND MAINTENANCE
54P00-01E
54P000727
(5) Removal
(6) Installation
3) To remove the bulb of the rear fog light
(4) from bulb holder, push in the bulb
and turn it counterclockwise. To install a
new bulb, push it in and turn it clock-
wise.
Interior light
Remove the lens by using a flat-bladed
screwdriver covered with a soft cloth as
shown. To install it, simply push it back in.
Front (without overhead console)
61MM0A207
Front (with overhead console)
61MM0A129
Center (without sunroof)
60G115
(5)
(6)(4)
OPEN
PUSH
TILT
CLOSE