11-5
SPECIFICATIONS
54P00-01E
ITEM: Recommended fuel / lubricants and capacities (approx.)
Fuel See “FUEL RECOMMENDATION” section. 47 L (10.3 Imp gal)
Engine oil
Gasoline
Except
for
MexicoClassification: ACEA A1/B1, A3/B3, A3/B4, A5/B5
API SL, SM or SN
ILSAC GF-3, GF-4 or GF-5
Viscosity: SAE 0W-203.9 L (6.9 Imp pt)
(replacement with oil filter)
For
MexicoEngine oil with “Starburst” symbol
DieselClassification: ACEA C2
Viscosity: SAE 0W-305.65 L (9.9 Imp pt)
(replacement with oil filter)
Engine coolant
Gasoline
“SUZUKI LLC: Super (Blue) Coolant”5.8 L (10.2 Imp pt)
(including reservoir tank)
Diesel5.5 L (9.7 Imp pt)
(including reservoir tank)
Manual transaxle oil 5M/T
“SUZUKI GEAR OIL 75W-80”2.5 L (4.4 Imp pt)
6M/T 2.1 L (3.7 Imp pt)
Transfer oil 4WD “SUZUKI GEAR OIL 75W-85” 0.93 L (1.6 Imp pt)
Rear differential oil 4WD “SUZUKI GEAR OIL 75W-85” 0.8 L (1.4 Imp pt)
Brake fluid / Clutch fluid
SAE J1704 or DOT4Refill to the proper oil level according
to the instructions in “INSPECTION
AND MAINTENANCE” section.
54P00-01E
No-Using Conditions
- When temperature under -40.
- On miring or sand ground.
- On big gradient road.
-In extreme nature condition: rainstorm, typhoon, cyclone, snowstorm, thunder-storm, etc.
- Loading dangerous heavy, for instance: melted metal, acidity substance, radioactivity
substance or specially crisp goods.
-Contact with hood directly.
-Using on boat.
-The ground with difference in level.
Operation instructions
Whenever a wheel is changed, always remove any corrosion
that may be present on inside of wheel and wheel mounting
surface on vehicle.
Details:
Please operate according to the “operation instructions”.
Operate the jack on the level ground while checking the jack
and the load.
Mustn’t operate under raising load, unless the load is fastened
surely.
- Park the car on the flat, level ground and apply the brake
firmly.
- Set transmission in “reverse”(automatic transmission in
“park”).
- Turn on the hazard warning flasher.
- Remove jacking tools and spare tire from stowage area.
- Block front and rear of wheel diagonally opposite wheel
being removed before operating jack.
- Loosen, but do not remove wheel nuts by turning wrench counter clockwise.
- Raise jack until jack-head groove fits boss of frame see illustrations.
- Operate jack with slow, smooth motion, using jack handle.
- Raise vehicle so an inflated tire will just clear surface, remove nuts and wheel.
- Install wheel, then slightly tighten each nut, wheel must be seated on hub.
- Lower vehicle, and fully tighten wheel nuts in across-cross sequence by turning wrench
clockwise.
Maintenance
- Please prevent the JACK SCREW from accretion of dirt.
- Check the nameplate, keep the shape same as original.
- No-rejigger the jack’s construction privately.
- After any use, consult immediately your Suzuki Dealer or Service Partner for inspection
and maintenance of the jack.
- If the label (sticker) is damaged, please consult your Suzuki Dealer or Service Partner.
>ö>í>ï>÷>õ>ú>ó>Ì
>ü>û>õ>ú? >Ì
>ö>í>ï>÷>õ>ú>ó>Ì>ü>û>õ>ú? >Ì
>ö>í>ï>÷>Ì>ô>í>ú>ð>ø>ñ>Ì>î>í>þ>Ì>ö>í>ï>÷>Ì>ô>í>ú>ð>ø>ñ>Ì
