2022 SUZUKI CELERIO maintenance

7-18
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
Tires
68KH075
The front and rear tire pressure specifica- tions for your vehicle are listed on the TireInformation Label. Both the front and rear tires should have the specified tire pres- sure.Note that the value does not apply to the compact spare tire, if equipped.
Tire InspectionInspect your vehicle’s tires at least once a month by performing the following checks:
1) Measure the air pressure with a tire gauge. Adjust the pressure if neces- sary. Remember to check the spare tire, too.
52KM110
(1) Tread wear indicator(2) Indicator location mark
2) Check that the depth of the tread groove is more than 1.6 mm (0.06 in.).To help you check this, the tires have molded-in tread wear indicators in the grooves. When the indicators appearon the tread surface, the remaining depth of the tread is 1.6 mm (0.06 in.) or less and the tire should be replaced.3) Check for abnormal wear, cracks and damage. Any tires with cracks or other damage should be replaced. If any tiresshow abnormal wear, have them inspected by your MARUTI SUZUKI dealer.
4) Check for loose wheel nuts. 5) Check that there are no nails, stones orother objects sticking into the tires.
EXAMPLE
WA R N I N G
• Air pressures should be checkedwhen the tires are cold or you mayget inaccurate readings. • Check the inflation pressure from time to time whil e inflating the tire gradually, until the specified pres- sure is obtained. • Never under inflate or over inflatethe tires. Under inflation can cause unusual handling characteristics or cancause the rim to slip on the tire bead, resulting in an accident or damage to the tire or rim.• Overinflation can cause the tire to burst, resulting in personal injury. Overinflation can also causeunusual handling characteristics which may result in an accident.
(1)
(2)
EXAMPLE
CAUTION
Hitting curbs and running over rocks can damage tires and affect wheelalignment. Be sure to have tires and wheel alignment checked periodi- cally by your MARUTI SUZUKI dealer.
156

7-19
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
Tire Rotation
5-tire rotation and 4-tire rotation
80JK040
To avoid uneven wear of your tires and to prolong their life, rotate the tires as illus- trated. Tires should be rotated as men-tioned in periodic maintenance schedule. After rotation, adjust front and rear tire pressures to the specification listed onyour vehicle’s Tire Information Label.
Wheel Balancing
If the vehicle vibrates abnormally on smooth road, have the wheel balanced atMARUTI SUZUKI Authorized Workshop
Wheel Alignment
In case of abnormal tire wear or pulling towards one side, have the wheel aligned at MARUTI SUZUKI Authorized Workshop.
BatteryWA R N I N G
• This is important to ensure propersteering and handling of the vehi-cle. Never mix tires of different size or type on the four wheels of your vehicle. The size and type of tiresused should be only those approved by MARUTI SUZUKI as standard or optional equipment foryour vehicle. • Replacing the wheels and tires equipped on your vehicle with cer-tain combinations of aftermarket wheels and tires can significantly change the steering and handlingcharacteristics of your vehicle. • Therefore, use only those wheel and tire combinations approved byMARUTI SUZUKI as standard or optional equipment for your vehi- cle.
NOTICE
Replacing the original tires with tires of a different size may result in false speedometer or odometer readings.
WA R N I N G
• Batteries produce flammable hydrogen gas. Keep flames and sparks away from the battery or an explosion may occur. Never smokewhen working in the vicinity of the battery. • When checking or servicing thebattery, disconnect the negative cable. Be careful not to cause a short circuit by allowing metalobjects to contact the battery posts and the vehicle at the same time. • To avoid harm to yourself or dam-age to your vehicl e or battery, fol- low the jump starting instructions in the “EMERGENCY SERVICE”section of this manual if it is neces- sary to jump start your vehicle.
157

7-20
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
76MH0A136
For maintenance-free battery (cap-less type), you need not add water. For tradi-tional type battery, which has water filler caps, the level of the battery solution must be kept between the “MAX” and the “MIN”level lines at all times. If the level is found tobe below the “MIN” level line, add distilledwater to the “MAX” level line. You shouldperiodically check the battery, battery termi- nals, and battery hold-down bracket for cor- rosion. Remove corrosion using a stiff brushand ammonia mixed with water, or bakingsoda mixed with water. After removing cor-rosion, rinse with clean water.
If your vehicle is not going to be driven for amonth or longer, disconnect the cable fromthe negative terminal of the battery to help prevent discharge.
Replacement of the battery
51KM039
To remove the battery: (1) Disconnect the negative cable (1). (2) Disconnect the positive cable (2). (3) Remove the retainer nuts (3) andremove the retainer (4) (4) Remove the battery.
To install the battery: (1) Install the battery in the reverse order of removal. (2) Tighten the retainer nuts and battery cables securely.
NOTE: When the battery is disconnected, some of the vehicle’s function will be initialized and/or deactivated. These function are required to reset after the battery is reconnected.
Fuses
Your vehicle has three types of fuses, asdescribed below:
Main fuse The main fuse takes current directly fromthe battery.
Primary fuses These fuses are between the main fuse and individual fuses, and are for electrical load groups.
Individual fuses These fuses are for individual electrical cir-cuits.
Fuses in the Engine Compartment
68KH076
CAUTION
Do not overfill th e battery with dis- tilled water in order to avoid spillage.
EXAMPLE - 1 EXAMPLE - 2(1)
(2)
(3)
(4)
EXAMPLE
(1)
(2)
(3)
(27)
(28)
158

7-21
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
68KH077
76MH036
The main fuse, primary fuses and some of the individual fuses are located in the engine compartment. If the main fuse blows, no electrical component will func-tion. If a primary fuse blows, no electrical component in the corresponding load group will function. When replacing themain fuse, a primary fuse or an individual fuse, use a Maruti genuine replacement.
MAIN FUSE/PRIMARY FUSE
(1) 80A FL1 (PETROL)
120A FL1 (DIESEL)
(4)
(24) (25) (26)
(13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23)
(10)
(11)
(12)
(5) (6) (7) (8) (9)
(29)
(30)
(31)
(32)
(33)
(34)
(35)
(36)
(2) 50A FL5 (PETROL)
40A FL5 (DIESEL)
(3) 50A FL4
(4) – Front fog light relay
(5)

7-22
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
To remove a fuse, use the fuse puller pro- vided in the fuse box. The amperage of each fuse is shown in the back of the fuse box cover.
60G111
NOTE:Make sure that the fuse box always carriesspare fuses.
Fuses under the Dash Board
68KH078
76MH0A111
WA R N I N G
If the main fuse or a primary fuse blows, be sure to have your vehicleinspected by an authorized MARUTI SUZUKI dealer. Always use a Maruti genuine replacement. Never use asubstitute such as a wire even for a temporary repair, or extensive electri- cal damage and a fire can result.
EXAMPLE
BLOWN
OK
EXAMPLE
(7) (8) (9) (10) (11) (12)
(19) (14)(13) (15) (16) (17) (18) (20)
(23)
(24)
(21)
(22)
(1) (2) (3) (4) (5) (6)
160

7-23
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
The fuse box is located under the driver’s side of the dashboard. Remove the fuse box cover by pushing inat both ends and pulling off the cover.
81A283
Bulb ReplacementMAIN FUSE/PRIMARY FUSE
(1) 10A Stop light
(2) 30A Blower motor
(3) 10A ST SIG
(4) 15A Accessory
(5) 10A Rear fog light
(6) 10A Tail light
(7) 10A Back-up light
(8) 10A ABS
(9) 10A Meter
(10) 15A Ignition coil
(11) 20A Wiper/Washer
(12) 10A IG2 SIG
(13) 10A IG1 SIG
(14) 10A Air bag
(15) 20A Power window timer
(16) 20A Door lock
(17) 15A Horn/Hazard
(18) 20A Rear defogger
(19) 15A Dome
(20) 30A Power window
(21) 7.5A ACC 2
(22) 15A Radio 2
(23) – Blank
(24) – Blank
WA R N I N G
Always be sure to replace a blown fuse with a fuse of the correct amper- age. Never use a substitute such as aluminum foil or wire to replace ablown fuse. If you replace a fuse and the new one blows in a short period of time, you may have a major electri-cal problem. Have your vehicle inspected immediately by your MAR- UTI SUZUKI dealer.
BLOWN OK
CAUTION
• Light bulbs can be hot enough toburn your finger right after being turned off. This is true especially for halogen headlight bulbs.Replace the bulbs after they become cool enough. • The headlight bulbs are filled withpressurized halogen gas. They can burst and injure you if they are hit or dropped. Handle them carefully.
NOTICE
The oils from your skin may cause ahalogen bulb to overheat and burst when the lights are on. Grasp a new bulb with a clean cloth.
NOTICE
Frequent replacement of a bulb indi-cates the need for an inspection of the electrical system. This should be carried out by your MARUTI SUZUKIdealer.
161

7-24
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
Headlights
Halogen headlights (1)
76MH0A112
76MH0A113
1) Open the engine hood. Disconnect the coupler (2). Remove the sealing rubber(3).
76MH0A114
2) Push the retaining spring (4) forward and unhook it. Then remove the bulb(5). Install a new bulb in the reverse order of removal.
76MH0A115
NOTE: You can see the position of retaining springfrom the hole of headlight.
Side Turn Signal Light (if equipped)
76MH0A006
1) Remove the light housing (1) by sliding to left with your finger.
76MH0A007
2) Turn the bulb holder (2) clockwise and pull it out from the light housing.
(1)
(3)
(2)
EXAMPLE
(4)
(5)
EXAMPLE
(1)
(2)
162

7-25
INSPECTION AND MAINTENANCE
76MH1-74E
76MH1-74E
76MH0A008
(4) Removal (5) Install
3) To remove and install the bulb of the turn signal light (3), simply pull out orpush in the bulb.
Front Turn Signal Light (1)
Front Position Light (2)
76MH0A116
76MH0A117
1) Open the engine hood. To remove the bulb holder of the front turn signal light (1) or the front position light (2) from thelight housing, turn the holder counter- clockwise and pull it out.
61MM0B078
(3) Removal(4) Install
2) To remove the bulb of the front turn sig- nal light (1) from the bulb holder, push in the bulb and turn it counterclockwise.To install a new bulb, push it in and turn it clockwise. To remove and install the bulb of thefront position light (2), simply pull out or push in the bulb.
Front Fog Light (if equipped)
1) Start the engine. Turn the steeringwheel to the opposite side of the replac- ing fog light to replace the bulb easily.Then turn off the engine.
76MH0A119
2) Remove the clips (1) by prying it off witha flat blade screwdriver as shown in theillustration.
(3)
(4)
(5)
(1)
(2)
(2)
(1)
(2)
(1)
(3)
(4)
EXAMPLE
(1)
EXAMPLE
163