2022 NISSAN GT-R battery

to change the mile-
age. Push and hold the switch to
increase the number every 600 miles
(1,000 km).
. Set to “—” to set no reminders.
. To reset the accumulated mileage to
zero, go to the RESET screen, then
push the NEXT switch
and confirm
with the ENTER switch.
NOTE:
. To restore the mileage to the origi-
nal figure after resetting, push the
NEXT switch
again.
. When the battery terminal is discon-
nected, the set mileage will be
erased and the settings will return
to their default settings.
Engine oil level:
This can be used to check the pre-start oil
level while the engine is running. Select
SETTING > MAINTENANCE > OIL > ENGINE
OIL > LEVEL.
If the low level reminder appears, check
the level using the engine oil dipstick.
(
“Checking engine oil level” page 8-9)

NOTICE
Make sure the front seatback does
not contact the rear seat when re-
clining the seat. When the front seat
is reclined to the rearmost position, it
may contact the rear seat. This may
cause an indentation in the seat-
back.
FRONT SEATS
Front power seat adjustmentOperating tips
.The power seat motor has an auto-
reset overload protection circuit. If the
motor stops during operation, wait 30
seconds, then reactivate the switch.
. Do not operate the power seat switch
for a long period of time when the
engine is off. This will discharge the
battery.
Safety — Seats, seat belts and supplemental restraint system
1-3

1 second.
NOTE:
When the battery is disconnected, the
memory for trips
is erased, and
both return to zero.
TACHOMETERThe tachometer indicates the engine
speed in revolutions per minute (rpm).
Do not rev the engine into the red zone
.
NOTICE
When engine speed approaches the
red zone, shift to a higher gear or
reduce engine speed. Operating the
engine in the red zone may cause
serious engine damage.
ENGINE COOLANT TEMPERATURE
GAUGEThe gauge indicates the engine coolant
temperature.
The engine coolant temperature is within
the normal range when the gauge needle
points within the zone
shown in the
illustration.
The engine coolant temperature varies
with the outside air temperature and
driving conditions.

to go to ALERT > UPSHIFT. The
current status of the upshift indicator will
be shown on the UPSHIFT screen. Note
that the function is set to AUTO as the
factory default setting.
To change the upshift indicator mode,
choose SETTING on the UPSHIFT screen.
Set one of the following modes by push-
ing the NEXT switch
, and then push
ENTER
to complete.
. AUTO
. 3,000 to 6,300 RPM (MANUAL)
. OFF
The number will increase by 100 RPM. To
increase the number by 500 RPM, push
and hold the NEXT switch
.
ExampleWhen the maximum engine speed is
desired:
Set the upshift indicator to AUTO. The
yellow indicator illuminates approxi-
mately 700 RPM before the red zone,
and the red indicator illuminates just
before the red zone.
When the maximum engine torque is
desired:
Set the figure at 6,000 RPM. The green
indicator starts flashing from approxi- mately 5,500 RPM and illuminates at
6,000 RPM.
When breaking-in the vehicle:
To help avoid high engine speeds during
break-in, set the upshift indicator to less
than 3,500 RPM. The green indicator
starts flashing approximately 500 RPM
before the set figure and illuminates from
the set figure. (
“Break-in schedule”
page 5-40)
NOTE:
. There may be a slight difference
between the timing of the upshift
indicator illumination and the tach-
ometer indication.
. When the battery terminal is discon-
nected, the set memory will be
erased and the mode returns to the
default.
INSTRUMENT BRIGHTNESS CON-
TROLThe instrument brightness can be ad-
justed when the ignition switch is in the
ON position. Push the switch to adjust the
brightness up
or down
. The bright-
ness level is shown on the vehicle infor-
mation display.
When the headlights are on, the bright-
ness of the interior switches is also
adjusted at the same time.

SETTING (drive computer)This is used to set the alert, maintenance
and optional settings.
Use the NEXT switch
to select an
item, then confirm with the ENTER switch
to change to the corresponding
setting screen.
To return to the initial setting screen,
push and hold the ENTER switch
for
more than 1 second. NOTE:
.
When the battery terminal is discon-
nected, the set memory will be
erased and the settings return to
the default.
. Setting is not possible in the follow-
ing cases.
—The vehicle is being driven.
— A warning display is active.
— The instrument brightness con-
trol level display is active.
— The cruise control status is dis-
played.
AlertThis function can be used to make
settings for the upshift indicator, “time
to rest” indicator and low outside tem-
perature warning.
Upshift indicator:
For details concerning the upshift indica-
tor, refer to the following section.
(
“Upshift indicator” page 2-10)

to go to ALERT > UPSHIFT. The
current status of the upshift indicator will
be shown on the UPSHIFT screen. Note
that the function is set to AUTO as the
factory default setting.
To change the upshift indicator mode,
choose SETTING on the UPSHIFT screen.
Set one of the following modes by push-
ing the NEXT switch
, and then push
ENTER
to complete.
. AUTO
. 3,000 to 6,300 RPM (MANUAL)
. OFF
The number will increase by 100 RPM. To
increase the number by 500 RPM, push
and hold the NEXT switch
.
ExampleWhen the maximum engine speed is
desired:
Set the upshift indicator to AUTO. The
yellow indicator illuminates approxi-
mately 700 RPM before the red zone,
and the red indicator illuminates just
before the red zone.
When the maximum engine torque is
desired:
Set the figure at 6,000 RPM. The green
indicator starts flashing from approxi- mately 5,500 RPM and illuminates at
6,000 RPM.
When breaking-in the vehicle:
To help avoid high engine speeds during
break-in, set the upshift indicator to less
than 3,500 RPM. The green indicator
starts flashing approximately 500 RPM
before the set figure and illuminates from
the set figure. (
“Break-in schedule”
page 5-40)
NOTE:
. There may be a slight difference
between the timing of the upshift
indicator illumination and the tach-
ometer indication.
. When the battery terminal is discon-
nected, the set memory will be
erased and the mode returns to the
default.
INSTRUMENT BRIGHTNESS CON-
TROLThe instrument brightness can be ad-
justed when the ignition switch is in the
ON position. Push the switch to adjust the
brightness up
or down
. The bright-
ness level is shown on the vehicle infor-
mation display.
When the headlights are on, the bright-
ness of the interior switches is also
adjusted at the same time.

1 second.
NOTE:
When the battery is disconnected, the
memory for trips
is erased, and
both return to zero.
TACHOMETERThe tachometer indicates the engine
speed in revolutions per minute (rpm).
Do not rev the engine into the red zone
.
NOTICE
When engine speed approaches the
red zone, shift to a higher gear or
reduce engine speed. Operating the
engine in the red zone may cause
serious engine damage.
ENGINE COOLANT TEMPERATURE
GAUGEThe gauge indicates the engine coolant
temperature.
The engine coolant temperature is within
the normal range when the gauge needle
points within the zone
shown in the
illustration.
The engine coolant temperature varies
with the outside air temperature and
driving conditions.

NOTICE
Make sure the front seatback does
not contact the rear seat when re-
clining the seat. When the front seat
is reclined to the rearmost position, it
may contact the rear seat. This may
cause an indentation in the seat-
back.
FRONT SEATS
Front power seat adjustmentOperating tips
.The power seat motor has an auto-
reset overload protection circuit. If the
motor stops during operation, wait 30
seconds, then reactivate the switch.
. Do not operate the power seat switch
for a long period of time when the
engine is off. This will discharge the
battery.
Safety — Seats, seat belts and supplemental restraint system
1-3