2022 NISSAN GT-R brake rotor

position.
3. To help prevent the vehicle from roll- ing into the street when parked on a
sloping drive way, it is a good practice
to turn the wheels as illustrated.
.
HEADED DOWNHILL WITH CURB:Turn the wheels into the curb and
move the vehicle forward until the
curb side wheel gently touches the
curb.
.
HEADED UPHILL WITH CURB:Turn the wheels away from the
curb and move the vehicle back
until the curb side wheel gently
touches the curb.
.
HEADED UPHILL OR DOWNHILL, NO
CURB:Turn the wheels toward the side of
the road so the vehicle will move
away from the center of the road if
it moves.
4. Push the ignition switch to the LOCK position.
For models without NCCB (NISSAN Car-
bon Ceramic Brake) package:
The GT-R uses brake pad materials that
have high metallic content. The brake pad
material helps maintain braking perfor-
mance in a wide range of weather and driving conditions.
For the first 3,000 - 6,000 miles (5,000 -
10,000 km) of the vehicle’s service life, and
for the first 3,000 - 6,000 miles (5,000 -
10,000 km) after a brake replacement, the
brake pad to brake rotor clearance is very
small. When parking, apply the parking
brake and move the shift lever to the
position. Idle the engine for more than 20
seconds without depressing the brake
pedal. This allows the brake pads to move
away from the rotor so the pad does not
contact the rotor.
Additionally, the brakes must be dry
before parking the vehicle after driving
on wet roads or after washing the vehicle.
If the roads are wet, lightly apply the
brakes for a short distance before parking
the vehicle to dry the brakes. After wash-
ing the vehicle, dry the brakes by driving
on a dry road for a few miles and apply
the brakes normally based on traffic and
road conditions.
The metallic brake pads and brake disc
rotor may rust together when the brakes
are not applied:
.
If the vehicle is not idled for 20
seconds without the brakes applied,
or if the brakes are applied when the
vehicle is shut off, the rotor and pads
can rust together, even when the brake pads are dry.
. If the brakes are wet when the vehicle
is parked and the parking brake is
applied for a long time.
It is recommended you contact a GT-R
certified NISSAN dealer if the brake pads
and brake rotor have rusted together.
For models with NCCB (NISSAN Carbon
Ceramic Brake) package:
(
“NCCB (NISSAN Carbon Ceramic
Brake)” page 8-20)
Starting and driving
5-47

operates to prevent one drive wheel from
slipping by transferring power to a non
slipping drive wheel. The VDC warning
light
will not flash. The VDC
system is automatically reset to on when
the ignition switch is placed in the off
position then back to the on position.
(
“Vehicle Dynamic Control (VDC)
warning light” page 2-34,
“Vehicle
Dynamic Control (VDC) off indicator light”
page 2-33)
The computer has a built-in diagnostic
feature that tests the system each time
you start the engine and move the vehicle
forward or in reverse at a slow speed.
When the self-test occurs, you may hear a
“clunk” noise and/or feel a pulsation in the
brake pedal. This is normal and is not an
indication of a malfunction.
may illuminate.
. If brake related parts such as
brake pads, rotors and calipers
are not standard equipment or
are extremely deteriorated, the
VDC system may not operate
properly and the VDC warning
light
may illuminate.
. If engine control related parts are
not standard equipment or are
extremely deteriorated, the VDC
warning light
may illuminate.
. When driving on extremely in-
clined surfaces such as higher
banked corners, the VDC system
may not operate properly and the
VDC warning light
may illumi-
nate. Do not drive on these types of roads.
. When driving on an unstable sur-
face such as a turntable, ferry,
elevator or ramp, the VDC warn-
ing light
may illuminate. This
is not a malfunction. Restart the
engine after driving onto a stable
surface.
. If wheels or tires other than the
those recommended are used,
the VDC system may not operate
properly and the VDC warning
light
may illuminate.
. The VDC system is not a substi-
tute for winter tires or tire chains
on a snow covered road.
NOTE:
. Always make sure the VDC is ON
before driving the vehicle by check-
ing that the VDC OFF indicator lights
on the meter and the VDC set-up
switch are not illuminated.
The GT-R is a high performance
vehicle and the VDC must be on/
activated to provide proper power-
train operation and intended driva-
bility.Starting and driving
5-55

BRAKE SYSTEM INFORMATION
Cracks on brake padThe friction material of the GT-R disc
brake pad is bonded to the pad backing
plate more strongly than conventional
brake pads to withstand the high brake
temperatures. The friction material and
backing plate expand due to heat at
different rates. Some cracks may be on
the surface of the friction material due to
the differences in expansion rates and the
strong bond between the friction material
and backing plate. The cracks do not
indicate the brake pads need to be
replaced. However, depending on the
condition of the cracks, the pads may
need to be replaced. It is recommended
you contact a GT-R certified NISSAN deal-
er.
. This is due to the temperature
differential that occurs because the sur-
faces of the disc rotors become hot while
the inside of the rotor is still cold. How-
ever, this poses no problem in terms of
brake performance, and does not indicate
a malfunction. The brakes do not need to

Rattles from brake pads and creaks
during braking
The high performance brake system of
vehicles equipped with the NCCB (NISSAN
Carbon Ceramic Brake) has more clear-
ance between its brake pad and brake
caliper than regular vehicles, and it uses a
large brake pad to ensure stable brakingperformance under a wide range of driv-
ing conditions such as extremely high
temperature areas or low temperature
areas like snow-covered roads. Accord-
ingly, you may hear light rattles from the
brake pad area when driving over a step,
which is not a malfunction. In addition,
you will hear creaks because of the
characteristics of the material for the disc
rotor. These creaks reduce with time and
wear.
Never park your vehicle for a long time
with the brake system wet.
The materials used for the brake disc
rotor and brake pads for specified NCCB
(NISSAN Carbon Ceramic Brake) are dif-
ferent from those used for the standard
brake system in GT-R. The rotor and pads
will be protected from adhesion caused
by rusting. However, never park your
vehicle for a long time with the brake
system wet. This helps maintain the brake
disc rotor and brake pads for a long time
and prevents an influence on the material
composition of the carbon ceramic rotor
and deterioration in the joint of brake disc
rotor’s full floating structure. Especially
during winter, be sure to park your vehicle
with the brake disc rotor and pads dry to
prevent them from being frozen and
damaged in below freezing temperature
conditions. The carbon ceramic brake forGT-R includes air bubbles in the rotor and
pads. Note that leaving them in the wet
condition tends to cause adhesion due to
freezing.
.
A screeching noise may be heard
when the brake pedal is depressed:
— When driving the vehicle for the first
time in the morning,
— After leaving the vehicle parked for extended periods of time, or
— When the vehicle is damp following rain showers or washing the vehi-
cle.
These sounds are normal. The noise is
caused when the brake pads absorb
moisture, and the noise stops after
the brake is applied several times.
. A screeching noise may also be heard
when the brake pedal is depressed:
— When repeatedly applying gentle
braking, especially on a curve at a
low speed, or
— When the brake rotors have circular scores with the brake temperature
high.
. The NCCB (NISSAN Carbon Ceramic
Brake) causes more screeching noise
in cold weather conditions than in
normal weather conditions.
GT-R Overview
GTR-29

dealer.
. The materials used for the brake
disc rotor and brake pads for NCCB
(NISSAN Carbon Ceramic Brake) are
different from those used for the
standard brake system in GT-R. The
rotor and pads will be protected
from adhesion caused by rusting.
However, never park your vehicle for
a long time with the brake system
wet. This helps maintain the brake
disc rotor and brake pads for a long
time and prevents an influence on
the material composition of the
carbon ceramic rotor and deteriora-
tion in the joint of brake disc rotor’s
full floating structure. Especially
during winter, be sure to park your
vehicle with the brake disc rotor and
pads dry to prevent them from
being frozen and damaged in below
freezing temperature conditions.
The carbon ceramic brake includes
air bubbles in the rotor and pads.
Note that leaving them in the wet
condition tends to cause adhesion
due to freezing.
Do-it-yourself
8-21

of each nut lightly
contacts the seat part
of the wheel
hole.
When replacing a front wheel, make
sure the hole in the wheel is aligned
with the pin on the brake disc rotor.
8. With the wheel nut wrench, tighten wheel nuts alternately and evenly in
the sequence illustrated (
,
,
,
,
)
until they are tight.
9. Lower the vehicle slowly until the tire touches the ground. Then, with the
wheel nut wrench, tighten the wheel
nuts securely in the sequence as
illustrated. Lower the vehicle comple-
tely.
WARNING
If the road wheels are hot, allow
them to cool sufficiently before tigh-
tening the wheel nuts. Otherwise, the
wheel nuts cannot be tightened to
specification.
NOTE:.
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
Do-it-yourself
8-45

Checking engine coolant level ..................... 8-8
Draining of coolant water ............................ 5-57
Engine coolant temperature gauge ........ 2-8
Coolant level and mixture ratio ................ GTR-15
Corrosion protection ................................................... 7-9
Cracks on brake pad ......................................... GTR-28
Cracks on the disc rotors .............................. GTR-28
Cruise control ................................................. 2-17, 5-35
Cruise control operations .................................... 5-37
Cruise control system warning ....................... 2-43
Cup holders ..................................................................... 2-63
Current fuel consumption ................................... 2-16
D
E

General maintenance ............................... 9-2, 9-3
Maintenance information ........................... GTR-3
Maintenance precautions ................................ 8-3
Maintenance requirement ............................... 9-2
Readiness for
Inspection/Maintenance test ................. 10-22
Scheduled maintenance ................................... 9-2
Seat belt maintenance .................................... 1-12
Maintenance log and records .......................... 9-28
Map lights ......................................................................... 2-69
Measurement of weights .................................. 10-19
Meters and gauges ....................................................... 2-6
Mirror
Inside mirror ............................................................ 3-27
Mirrors ........................................................................... 3-27
Outside mirrors ..................................................... 3-28
Vanity mirror ........................................................... 3-29
Vanity mirror lights ............................................ 2-71
Most common factors contributing to
vehicle corrosion ............................................................. 7-9
Multi Function Display Owner’s Manual ....... 4-2
N
NCCB (NISSAN Carbon
Ceramic Brake) ........................................... GTR-6, 8-20
Replacing brake pads and brake
disc rotors ................................................................. 8-21
NISSAN Advanced Air Bag System ................ 1-40
NISSAN Vehicle Immobilizer System ............ 2-50
No key warning ............................................................ 2-45 Noises are heard while driving .................. GTR-26
Normal mode ................................................................. 5-25
O
P