2022 NISSAN GT-R battery

to go to ALERT > UPSHIFT. The
current status of the upshift indicator will
be shown on the UPSHIFT screen. Note
that the function is set to AUTO as the
factory default setting.
To change the upshift indicator mode,
choose SETTING on the UPSHIFT screen.
Set one of the following modes by push-
ing the NEXT switch
, and then push
ENTER
to complete.
. AUTO
. 3,000 to 6,300 RPM (MANUAL)
. OFF
The number will increase by 100 RPM. To
increase the number by 500 RPM, push
and hold the NEXT switch
.
ExampleWhen the maximum engine speed is
desired:
Set the upshift indicator to AUTO. The
yellow indicator illuminates approxi-
mately 700 RPM before the red zone,
and the red indicator illuminates just
before the red zone.
When the maximum engine torque is
desired:
Set the figure at 6,000 RPM. The green
indicator starts flashing from approxi- mately 5,500 RPM and illuminates at
6,000 RPM.
When breaking-in the vehicle:
To help avoid high engine speeds during
break-in, set the upshift indicator to less
than 3,500 RPM. The green indicator
starts flashing approximately 500 RPM
before the set figure and illuminates from
the set figure. (
“Break-in schedule”
page 5-40)
NOTE:
. There may be a slight difference
between the timing of the upshift
indicator illumination and the tach-
ometer indication.
. When the battery terminal is discon-
nected, the set memory will be
erased and the mode returns to the
default.
INSTRUMENT BRIGHTNESS CON-
TROLThe instrument brightness can be ad-
justed when the ignition switch is in the
ON position. Push the switch to adjust the
brightness up
or down
. The bright-
ness level is shown on the vehicle infor-
mation display.
When the headlights are on, the bright-
ness of the interior switches is also
adjusted at the same time.

SETTING (drive computer)This is used to set the alert, maintenance
and optional settings.
Use the NEXT switch
to select an
item, then confirm with the ENTER switch
to change to the corresponding
setting screen.
To return to the initial setting screen,
push and hold the ENTER switch
for
more than 1 second. NOTE:
.
When the battery terminal is discon-
nected, the set memory will be
erased and the settings return to
the default.
. Setting is not possible in the follow-
ing cases.
—The vehicle is being driven.
— A warning display is active.
— The instrument brightness con-
trol level display is active.
— The cruise control status is dis-
played.
AlertThis function can be used to make
settings for the upshift indicator, “time
to rest” indicator and low outside tem-
perature warning.
Upshift indicator:
For details concerning the upshift indica-
tor, refer to the following section.
(
“Upshift indicator” page 2-10)

to change the mile-
age. Push and hold the switch to
increase the number every 600 miles
(1,000 km).
. Set to “—” to set no reminders.
. To reset the accumulated mileage to
zero, go to the RESET screen, then
push the NEXT switch
and confirm
with the ENTER switch.
NOTE:
. To restore the mileage to the origi-
nal figure after resetting, push the
NEXT switch
again.
. When the battery terminal is discon-
nected, the set mileage will be
erased and the settings will return
to their default settings.
Engine oil level:
This can be used to check the pre-start oil
level while the engine is running. Select
SETTING > MAINTENANCE > OIL > ENGINE
OIL > LEVEL.
If the low level reminder appears, check
the level using the engine oil dipstick.
(
“Checking engine oil level” page 8-9)

CAUTION
When the battery cable is removed
from the battery terminal, do not
close either of the front doors. The
automatic window adjusting func-
tion will not work and the side roof
panel may be damaged.
The power window has an automatic
adjusting function. When the door is
being opened, the window is automati-
cally lowered slightly to avoid contact
between the window and the side roof

, DOOR
and OFF
.
ON positionWhen the switch is in the ON position
,
the map lights will illuminate.
NOTICE
Do not use the light for extended
periods of time with the engine
stopped. This could result in a dis-
charged battery. NOTE:
The lights will also turn off after a
period of time when the lights remain
illuminated after the ignition switch has
been pushed to the OFF or LOCK posi-
tion to prevent the battery from becom-
ing discharged.
DOOR positionWhen the switch is in the DOOR position, the map lights will turn on when the
door is opened and turn off when the
door is closed. The map lights will turn off
approximately 15 seconds after the door
is closed with the ignition switch in the
OFF or LOCK position.
NOTE:
When the interior light control switch is
in the DOOR position and the door is
open, the light will remain on even
when the map light switch is pressed
to turn off.
Key-linked interior light control system:
OFF positionWhen the switch is in the OFF position
,
the map lights will not illuminate, regard-
less of any condition.

1. Intelligent Key (2 sets)
2. Mechanical key (inside Intelligent Keys) (2sets)
3. Key number plate (1 set)INTELLIGENT KEYYour vehicle can only be driven with the
Intelligent Keys which are registered to
your vehicle’s Intelligent Key system com-
ponents and NISSAN Vehicle Immobilizer
System components. As many as 4 In-
telligent Keys can be registered and used
with one vehicle. The new keys must be
registered by a GT-R certified NISSAN
dealer prior to use with the Intelligent
Key system and NISSAN Vehicle Immobi- lizer System of your vehicle. Since the
registration process requires erasing all
memory in the Intelligent Key compo-
nents when registering new keys, be sure
to take all Intelligent Keys that you have
to a GT-R certified NISSAN dealer.
NOTICE
.
Be sure to carry the Intelligent
Key with you when driving. The
Intelligent Key is a precision de-
vice with a built-in transmitter. To
avoid damaging it, please note
the following.
— The Intelligent Key is water
resistant; however, wetting
may damage the Intelligent
Key. If the Intelligent Key gets
wet, immediately wipe until it
is completely dry.
— Do not bend, drop or strike it against another object.
— Do not place the Intelligent Key for an extended period in
a place where temperatures
exceed 140°F (60°C).
— If the outside temperature is below 14°F (−10°C), the battery
of the Intelligent Key may not
KEYS

CAUTION
To prevent theft or accidents, be sure
to stop the engine and lock the doors
before stepping away from the ve-
hicle.
NOTICE
When the battery cable is removed
from the battery terminal, do not
close either of the front doors. The
automatic window adjusting func-
tion will not work, and the side roof
panel may be damaged.
(

Intelligent Key operating rangeThe Intelligent Key functions can only be
used when the Intelligent Key is within
the specified operating range from the
request switch. The operating range is
within 31.50 in (80 cm) from each request
switch.
NOTE:
.When the Intelligent Key battery is
discharged or strong radio waves
are present near the operating loca-
tion, the Intelligent Key system’s
operating range becomes narrower,
and the Intelligent Key may not
function properly. .
If the Intelligent Key is too close to
the door glass, handle or rear bum-
per, the request switches may not
function.
. When the Intelligent Key is within
the operating range, it is possible for
anyone who does not carry the
Intelligent Key to push the request
switch to lock/unlock the doors.
Intelligent Key operationYou can lock or unlock the doors without
taking the key out from your pocket or
bag.