2022 MERCEDES-BENZ E-CLASS CABRIOLET service

On-board computer:
4 Service 5
Engine oil level
One of thefo llowing message s will appear onthe
inst rument displa y:
R Engine oil level Measuring now: measu rement
of the oil le vel is not yet possible. #
Repeat there qu est aTer a maximum of
30 minutes' driving.
R Engine oil level OK andthe bar display for
indicating the oil le vel on the inst rument dis-
play is green and is between "min" and "max":
th e oil le vel is cor rect.
R Engine oil level Add 1,0 l andthe bar display
fo r indicating the oil le vel on the inst rument
display is orange and is below "min": #
Add 1 l of engine oil.
R Reduce engine oil level andthe bar display for
indicating the oil le vel on the inst rument dis-
play is orange and is abo ve"max": #
Drain o. any excess engine oil that has been
added. Todo so, consult a quali/ed specialist
wo rkshop.
R For engine oil level turn on ignition #
Switch on theve hicle tocheck the engine oil
le ve l.
R Engine oil level System inoperative: The oil
le ve l sensor is defective or not connected. #
Consult a quali/ed specialist workshop.
R Engine oil level System currently unavail. #
Close the bonnet.
T
T op up engine oil
op up engine oil &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
WARNING
ARNING Risk of /re and injury from
engine oil
If engine oil comes into contact with hot com-
ponent parts in the engine compartment, it
may ignite. #
Make sure that no engine oil is spilled
next tothe /ller opening. #
Allow the engine tocool o. and thor-
oughly clean the engine oil from compo-
nent parts before starting theve hicle. *
N
NOOTE
TE Engine damage caused byan inco r-
re ct oil /lter, incor rect oil or additi ves #
Do not use engine oils or oil /lters which
do not cor respond tothe speci/cations
ex plicitly prescribed forth e service inter-
va ls. #
Follow the inst ructions on the service
inter val display forch anging the engine
oil and obser vethe prescribed change
inter vals. #
Do not use additives. 304 304
Maintenance and care

R
Do not use car wash prog rammes with a /nal
hot wax treatment.
R Do not use paint cleaners, bu1ng or polishing
products, gloss preser vers,e. g. wa x.
In theev ent of paintwork damage:
R Always ha vepaintwork repairs car ried out at a
qu ali/ed specialist workshop.
R Make sure thera dar sensors function
(/ page 186). N
No
ot
tes on cleaning decor
es on cleaning decor ativ
ative f
e foils
oils Obser
vethe no tes on matt /nish care in thech ap-
te r "No tes on paintwork/matt /nish paintwork
care" (/ page 309). They also apply tomatt dec-
orative foils.
Obser vethe no tes on cleaning decorative foils to
av oid damage.
Cleaning
Cleaning
R For cleaning, use plenty of water and a mild
cleaning agent without additives or abrasive
substances (e.g. a car shampoo appr ovedfor
Mercedes-Benz). R
Remo vedirt as soon as possible. Avoid rub-
bing too hard in order tonot ir reparably dam-
age the decorative foil.
R Ifth ere is dirt on the /nish or if the decorative
fo il is dull: Use thePa int Cleaner recommen-
ded and appr ovedfo r Mercedes-Benz.
R Insect remains: Soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: Soak with water and rinse o.
aTer wards.
R Toprev ent water stains, dry a foil-wrapped
ve hicle with a soT, absorbent clo thaTer every
car wash.
A
A v
voiding damag
oiding damag e t
e to t
o t he decor
he decor ativ
ative f
e foil
oil
R The service life and colou ring of decorative
fo ils are impaired by:
- Sunlight
- Temp erature (e.g. hot air blo wer)
- Weather conditions
- Stone chippings and dirt
- Chemical cleaning agents
- Oily products R
Do not use polish on matt decorative foil. Po l-
ishing will ha vethe e.ect of shining thefo il-
wrapped sur face.
R Do not treat matt or st ructured decorative
fo ils with wax.Pe rm anent stains may occur.
Scratches, cor rosive deposits, areas a.ected by
cor rosion and damage caused byincor rect care
cannot alw ays be comple tely re paired. In this
case, contact a quali/ed specialist workshop.
Yo u can obtain more information on care and
cleaning agents from the manufacturer.
In the case of foil-wrapped sur faces, optical di.er-
ences may occur between the sur faces that we re
not pro tected bya decorative foil aTer removing a
decorative foil.
% Have workor repairs todecorative foils car-
ri ed out at a quali/ed specialist workshop
(e.g. in a Mercedes-Benz Se rvice Centre). N
No
ot
tes on cleaning and car
es on cleaning and car e of t
e of the
hesoT
soT t
top
op Obser
vethefo llowing no tes in order toprev ent
damage tothe soT top. 310
310
Maintenance and care

Light dirt
Light dirt
R Clean the soT top when dr y.
R Rinse with clean water.
N
N or
or mal t
mal t o hea
o hea vy dirt
vy dirt
R Clean the soT top with a brush and clean
wa ter.
R Clean stains and other heavy dirt with a brush
and soT-top cleaning agents recommended
and appr ovedfo r Mercedes-Benz.
R Brush from front toback in the direction of the
fa bric.
Av
Av oiding
oiding soT-t
soT-top
opdamage
damage
R Never use petrol, thinners, tar or stain
re mo ver or other or ganic sol vents.
R Remo vebird droppings immediatel y,as they
are cor rosive and can therefore cause the
soT-top fabric toleak.
R Never use a high-pressure cleaner.
R Do not use sharp-edged equipment toremo ve
ice and sno w.
Fr equent cleaning reduces the soT top's resist-
ance todirt. Torestore the e.ect, clean the soT to
p with the soT- topcleaning agents recommen-
ded and appr ovedfo r Mercedes-Benz.
Incor rect cleaning and care, as well as ageing,
can cause the soT- topseams toleak. If this hap-
pens, ha vethe soT- topseams sealed at a quali-
/ed specialist workshop, e.g. at your Mercedes-
Benz service centre.
% Place a suitable co verove rth e soT top if you
plan tolea vetheve hicle outside for a long
period of time. Cleaning AIRC
Cleaning AIRC
AP
AP Cleaning t
Cleaning t
he wind
he windde0ect
de0ector
or
* NO
NOTE
TEDamage tothe net due tousing a
high-pressure cleaner #
Never use a high-pressure cleaner to
clean the net of the wind de0ector. R
R
eq
eq uir
uir ements:
ements:
R The soT top is closed.
R The electric parking brake has been applied.
R The vehicle is switched on. #
Pull but ton1.
The wind de0ector between the windscreen
and the soT top will extend. Maintenance and ca
re
311
311

+
ENVIR
ENVIR
ONMENT
ONMENT AL NO
AL NOTE
TE Environmen tal
pollution caused byenvironmentally ir re-
sponsible disposal Ty
re sealant contains pollu tants. #
Have the tyre sealant bottle disposed of
professionall y,e.g. at a Mercedes-Benz
Service Centre. #
Stow the tyre sealant bottle and the tyre in0a-
tion compressor. #
Pull away immediatel y. #
Stop driving aTer appr oximately ten minutes
and check the tyre pressure using the tyre
in0ation compressor.
The tyre pressure must now be at least
130 kPa (1.3 bar/19 psi). &
W WARNING
ARNING Risk of accident due tothe
speci/ed tyre pressure not being attained
If th e speci/ed tyre pressure is not reached,
th e tyre is too badly damaged. The tyre seal-
ant cannot repair the tyre in this instance. The braking and driving
characteristics may be
gr eatly impaired. #
Do not continue driving. #
Consult a quali/ed specialist workshop. Countr
Countr
ies t
ies that hav
hat hav e Mer
e Mercedes-Benz Ser
cedes-Benz Ser vice24h:
vice24h:
yo u will /nd a stic ker with thete lephone number,
e.g. on the B‑pillar on the driver's side. #
Correct the tyre pressure if it is still at least
130 kPa (1.3 bar/19 psi). See the tyre pres-
sure table on the fuel /ller 0ap forva lues. #
T
T o incr
o incr ease t
ease t he tyr
he tyre pr
e pressur
essur e:
e:switch on the
tyre in0ation compressor. #
T To r o r educe t
educe t he tyr
he tyre pr
e pressur
essur e:
e:press pressure
re lease button 1next tomanome ter2. #
When the tyre pressure is cor rect, unscr ew
th e /lling hose from theva lve of the sealed
tyre. #
Screw theva lve cap onto theva lve of the
sealed tyre. #
Pull the tyre sealant bottle out of the tyre in0a-
tion compressor.
The /lling hose st ays on the tyre sealant bot-
tle. #
Drive tothe nearest quali/ed specialist work-
shop and ha vethe tyre, tyre sealant bottle and
/lling hose replaced there. Batt Batt
er
ery (v
y (v ehicle)
ehicle) N
No
ot
tes on t
es on t he 12 V batt
he 12 V batt ery
ery &
W
WARNING
ARNING Risk of an accident due towo rk
car ried out incor rectly on the battery
Wo rkcar ried out incor rectly on the battery
can, forex ample, lead toa short circuit. This 324
324
Breakdown assis
tance

#
During starting assistance, alw aysta ke
care toconnect only battery term inals of
identical polarity. #
During starting assistance, obser vethe
sequence described for connecting and
disconnecting the jump leads. #
Do not connect or disconnect the bat-
te ry term inals with the engine running. &
W
W ARNI NG
ARNI NGRisk of explosion due toexplo-
sive mixture of gases
An explosive mixture of gases can escape
from the battery during charging and starting
assis tance. #
Fire , naked 0ames, smoking and creating
spar ksmust be avoided. #
Make sure there is adequate ventilation. #
Do not stand overth e batter y. &
W
WARNI NG
ARNI NGRisk of explosion from a frozen
battery
A dischar ged battery may freeze at temp era-
tures slightly abo veor below freezing point.
During starting assistance or battery charging,
battery gas can be released. #
Always allow a battery tothaw before
ch arging it or per form ing starting assis-
ta nce. If
th e indicator/warning lamps in the inst rument
clus ter do not light up at low temp eratures, it is
ve ry likely that the dischar ged battery has frozen.
In this case you may neither jump-start theve hi-
cle nor charge the batter y.
The service life of a bat tery that has been thawed
may be dramatically shor tened. The starting char-
acteristics may be impaired, especially at low
te mp eratures.
It is recommended that you ha veath awe d battery
ch ecked at a quali/ed specialist workshop. All v
All v ehicles
ehicles
* NO
NOTE
TEDamage caused bynume rous or
ex tended attem ptsto start the engine Numerous or
extended attem ptsto start the
engine may damage the catalytic con verter
due tonon-combusted fuel. #
Avoid numerous and extended attem pts
to start the engine. Obser
vethefo llowing points during starting assis-
ta nce and when charging the batter y:
R Only use undamaged jump lead/charging
cables with a su1cient cross-section and
insulated term inal clamps.
R Non-insulated parts of thete rm inal clamps
must not come into contact with other me tal
parts while the jump lead/charging cable is
connected tothe battery/jump-start connec-
tion point.
R The jump lead/charging cable must not come
into contact with any parts which may mo ve
when the engine is running. Breakdown assistance
327 327

#
Remo veany existing moisture from the fuse
box using a dry clo th.#
Loosen scr ews4 and remo vefuse box lid 3
from theto p.
Closing
Closing #
Check whe ther the seal is positioned cor rectly
in cap 3. #
Insert lid 3into the brac ket at there ar of the
fuse box. #
Fold down lid 3ofthe fuse box and tighten
scr ews4. #
Insert co ver1 on bo thsides. #
Turn clips 2on co ver1 aqu arter-turn
clockwise. #
Close the bonnet. Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the coc
he coc kpit
kpit R
Obser vethe no tes on elect rical fuses
(/ page 334).
The fuse box is on the driver's side on the side of
th e cockpit under a co ver. #
Toopen and close it, consult a Mercedes-Benz
Service Centre. Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the fr
he front
ont
passeng
passeng er f
er foo
ootw
twell
ell Obser
vethe no tes on elect rical fuses
(/ page 334). #
T To open: o open: open cover1 inthe direction of the
ar ro w and remo veit. #
T To close:
o close: reinsert co ver1. Opening and closing t Opening and closing t
he fuse bo
he fuse box in t
x in the boot
he boot Obser
vethe no tes on elect rical fuses
(/ page 334). 336
336
Breakdown assistance

*
N
N O
OTE
TE Damage tocomponents of theve hi-
cle body or chassis due to/tted snow
ch ains If
yo u /t snow chains tothe front wheels of
4MATIC vehicles, you may damage compo-
nents of theve hicle body or chassis. #
Only /t snow chains tothere ar wheels
of 4MATIC vehicles. Obser
vethefo llowing no tes when using snow
ch ains:
R Snow chains are only permissible for cer tain
wheel/tyre combinations. You can obtain
information about this from a Mercedes-Benz
Service Centre.
R For saf etyre asons, only use snow chains that
ha ve been speci/cally appr oved foryo ur vehi-
cle byMercedes-Benz, or snow chains with
th e same quality standard.
R Comply with the installation inst ructions of the
snow chain manu facturer.
R If snow chains are /tted, the maximum per-
missible speed is 50 km/h. R
V
V ehicles wit
ehicles wit h A
h Activ
ctiv e P
e Par
arking Assist
king Assist: :do not use
Ac tive Parking Assist when snow chains are
/tted.
R V
Vehicles wit
ehicles wit h lev
h level contr
el contr ol:
ol:if snow chains are
/tted, only drive at raised vehicle le vel
( / page 221).
% You can permanently limit the maximum
speed for driving with winter tyres
(/ page 197).
% You can deactivate ESP ®
to pull away
( / page 190). This allo ws the wheels tospin,
achieving an increased driving forc e. T
T
yr
yr e pr
e pr essure
essure N
No
ot
tes on tyr
es on tyr e pr
e pressure
essure &
W
WARNING
ARNING Risk of accident due toinsu1-
cient or excessive tyre pressure
Un derin0a tedorove rin0ated ty res pose in par-
ticular thefo llowing risks:
R The tyres can burst. R
The tyres can wearexcessively and/or
une venly.
R The driving characteristics as well as the
stee ring and braking characteristics may
be greatly impaired. #
Comply with there commended tyre
pressure and check the tyre pressure of
all tyres, including the spare wheel, regu-
lar ly:
R monthly
R when the load changes
R before embarking on a lon ger journey
R if operating conditions change, e.g. o.-
ro ad driving #
Adjust the tyre pressure, if necessar y. Ty
re pressure which is too high or too low can:
R Shor tenth e service life of the tyres.
R Cause increased tyre damage.
R Adve rsely a.ect driving characteristics and
th us driving saf ety, e.g. due toaquaplaning. Wheels and tyres
339
339

If
th e preceding tyre sizes are complemented by
th e+ symbol, the tyre pressure information
fo llowing sho wsalternative tyre pressures. Fuel
consum ption may then increase slightl y.
The load conditions "pa rtially laden" and "fully
laden" are de/ned in theta ble for di.erent num-
bers of passengers and amounts of luggage. The
actual number of seats may di.er from this. T
T
yr
yr e pr
e pr essur
essur e monit
e monit or
oring syst
ing syst em
em F
F
unction of t
unction of t he tyr
he tyre pr
e pressur
essur e monit
e monit or
oring syst
ing syst em
em
The system checks the tyre pressure and the tyre
te mp erature of the tyres /t tedtotheve hicle by
means of a tyre pressure sensor.
The tyre pressure and the tyre temp erature
appear in the on-board computer (/ page 341).
If th ere is a substantial pressure loss or if the tyre
te mp erature is excessive, you will be warned with
display messages (/ page 421) ortheh
wa rning lamp in the inst rument cluster
(/ page 444).
The tyre pressure monitoring system is only an
aid. It is the driver's responsibility toset the tyre pressure
tothere commended cold tyre pressure
suitable forth e operating situation.
In most cases, the tyre pressure monitoring sys-
te m will automatically update the new refere nce
va lues aTer you ha vechanged the tyre pressure.
Yo u can, ho wever, also update there fere nce val-
ues byrestarting the tyre pressure monitoring
system manually (/ page 342).
Syst
Syst em limits
em limits
The system may be impaired or may not function
particular lyin thefo llowing situations:
R incor rect refere nce values were ta ught in
R sudden pressure loss caused byafo re ign
object penetrating the tyre, forex ample
R there is a malfunction caused byano ther radio
signal source
Chec
Chec king t
king t he tyr
he tyr e pr
e pressur
essur e wit
e with t
h the tyr
he tyr e pr
e pressure
essure
monit
monit or
oring syst
ing syst em
em
R
R eq
equir uir ements:
ements:
R The vehicle is switched on. On-board computer:
4 Service 5
Tyres
One of thefo llowing displa ysappears:
R Current tyre pressure and tyre temp erature of
th e individual wheels: R
Tyre pressures will be displayed after a few
minutes of driving
R Tyre pressure monitor active: thete ach-in
process of the system is not yetcomple te. The
tyre pressures are already being monitored. #
Compare the tyre pressure with there com-
mended tyre pressure forth e cur rent ope rat-
ing condition (/ page 340).Additionall y, Wheels and tyres
341 341