2022 MERCEDES-BENZ E-CLASS CABRIOLET light

Seat belts
Seat belts
R Clean wi thluk ewa rmand soapy water.
R Do not use chemical cleaning agents.
R Do not dry byheating them toove r 80°C or
ex posing them todirect sunlight.
Display
Display
R Switch o. the display and let it cool down.
R Clean the sur face carefully with a micro/bre
clo thand a suitable displ aycare product (TFT-
LC D).
R Do not use any other agents.
Head-up displ ay
Head-up display
R Clean with a soT, non-static, lint-free clo th.
R Do not use cleaning agents.
Plas
Plastic tr tic tr im
im
R Clean with a damp micro/bre clo th.
R For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
R Do not attach stic kers, /lms or similar materi-
als. R
Do not allow cosmetics, insect repellent or
sun cream tocome in contact with the plastic
trim.
R
R eal w
eal w ood and tr
ood and tr im elements
im elements
R Clean with a micro/bre clo th.
R Blackpiano-lacquer look: Clean with a damp
clo thand soapy water.
R For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
R Do not use sol vent-based cleaning agents, pol-
ishes or waxes.
R
R oof lining
oof lining
R Clean with a brush or dry shampoo.
Car
Car pet
pet
R Use a carpet and textile cleaning agent recom-
mended for Mercedes-Benz.
St
St eer
eer ing wheel made of g
ing wheel made of g enuine leat
enuine leather or DINA-
her or DINA-
MICA
MICA
* NO
NOTE
TEDamage caused bywrong cleaners #
Do not use sol vent-based cleaning
agents such as tarre mo ver or wheel cleaner; neither should
you use polishes
or wa xes. Otherwise you may damage
th e /nish. R
Clean with a damp clo thand 1% soapy water
solution and then wipe with a dry clo th.
R For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
R Leather care: Use a leather care agent that
has been recommended for Mercedes-Benz.
R Do not allow the leather tobecome too damp.
R Do not use a micro/bre clo th.
% Leather is a natural product. It exhibits natural
sur face properties such as di.erences in
st ru cture, mar kscaused bygrow thand injury
or subtle colour di.erences. These sur face
properties are characteristics of leather and
not material faults. What's more, leather is
subject toa natural ageing process during
which the sur face properties change.
Genuine leat
Genuine leat her seat cov
her seat covers
ers
R Vacuum away dirt (e.g. crumbs or dust) and
th en clean the seat co vers with a damp cotton Main
tenance and ca re
315
315

#
During starting assistance, alw aysta ke
care toconnect only battery term inals of
identical polarity. #
During starting assistance, obser vethe
sequence described for connecting and
disconnecting the jump leads. #
Do not connect or disconnect the bat-
te ry term inals with the engine running. &
W
W ARNI NG
ARNI NGRisk of explosion due toexplo-
sive mixture of gases
An explosive mixture of gases can escape
from the battery during charging and starting
assis tance. #
Fire , naked 0ames, smoking and creating
spar ksmust be avoided. #
Make sure there is adequate ventilation. #
Do not stand overth e batter y. &
W
WARNI NG
ARNI NGRisk of explosion from a frozen
battery
A dischar ged battery may freeze at temp era-
tures slightly abo veor below freezing point.
During starting assistance or battery charging,
battery gas can be released. #
Always allow a battery tothaw before
ch arging it or per form ing starting assis-
ta nce. If
th e indicator/warning lamps in the inst rument
clus ter do not light up at low temp eratures, it is
ve ry likely that the dischar ged battery has frozen.
In this case you may neither jump-start theve hi-
cle nor charge the batter y.
The service life of a bat tery that has been thawed
may be dramatically shor tened. The starting char-
acteristics may be impaired, especially at low
te mp eratures.
It is recommended that you ha veath awe d battery
ch ecked at a quali/ed specialist workshop. All v
All v ehicles
ehicles
* NO
NOTE
TEDamage caused bynume rous or
ex tended attem ptsto start the engine Numerous or
extended attem ptsto start the
engine may damage the catalytic con verter
due tonon-combusted fuel. #
Avoid numerous and extended attem pts
to start the engine. Obser
vethefo llowing points during starting assis-
ta nce and when charging the batter y:
R Only use undamaged jump lead/charging
cables with a su1cient cross-section and
insulated term inal clamps.
R Non-insulated parts of thete rm inal clamps
must not come into contact with other me tal
parts while the jump lead/charging cable is
connected tothe battery/jump-start connec-
tion point.
R The jump lead/charging cable must not come
into contact with any parts which may mo ve
when the engine is running. Breakdown assistance
327 327

begin with POSITIVE contact
2onyour own
ve hicle /rst. #
Dur
During st
ing st ar
arting assist
ting assist ance:
ance:startthe engine of
th e donor vehicle and run at idle speed. #
Connect the negative term inal of the donor
battery and ear thpoint 3ofyour ow nve hicle
by using the jump lead/charging cable. Begin
with the donor battery /rst. #
Dur
During st
ing st ar
arting assist
ting assist ance:
ance:startthe engine of
yo ur ow nve hicle. #
Dur
During t
ing t he c
he char
harging pr
ging pr ocess:
ocess: startthech arg-
ing process. #
Dur
During st
ing st ar
arting assist
ting assist ance:
ance:letthe engines run
fo r se veral minutes. #
Dur
During st
ing st ar
arting assist
ting assist ance:
ance:before disconnect-
ing the jump lead, switch on an electrical con-
sumer on your ow nve hicle, e.g. there ar win-
dow heater or lighting.
When the starting assistance/charging process is
comple te, per form thefo llowing steps: #
Firs t, re mo vethe jump lead/charging cable
from ear thpoint 3and the negative term inal of
the donor batter y,then POSITIVE contact
2 and the positive term inal of the donor bat-
te ry. Begin each time with the contacts on
yo ur ow nve hicle /rst. #
ATer removing the jump lead/charging cable,
close co ver1 of POSITIVE contact 2.
Fu rther information can be obtained at a quali/ed
specialist workshop. R
R
eplacing t
eplacing t he 12 V batt
he 12 V batt ery
ery #
Obser vethe no tes on the 12 V battery
(/ page 324).
Mercedes-Benz recommends that you ha vethe
12 V battery replaced at a quali/ed specialist
wo rkshop, e.g. at a Mercedes-Benz Se rvice
Centre.
Obser vethefo llowing no tes if youwa nttoreplace
th e battery yourself:
R Alwaysre place a faulty battery with a battery
which meets the speci/c vehicle requ ire-
ments. The
vehicle is equipped with an AGMtech nol-
ogy bat tery (Absorbent Glass Mat) or a lith-
ium-ion batter y.Fu llve hicle functionality is
only guaranteed with an AGM bat tery or lith-
ium-ion batter y.Fo r saf etyre asons, Mercedes-
Benz recommends that you only use batteries
which ha vebeen tested and appro vedfo ryo ur
ve hicle byMercedes-Benz.
R Carryove r de tach able parts, such as vent
hoses, elbow /ttings or term inal co vers from
th e battery being replaced.
R Make sure that theve nt hose is alw ays con-
nected tothe original opening on the side of
th e batter y.
Fi t any existing or supplied cell caps.
Otherwise, gases or battery acid could
escape.
R Make sure that de tach able parts are recon-
nected in the same way. Breakd
own assistance
329 329

&
W
WARNI NG
ARNI NGRisk of accident due torepea-
te d pressure drop in the tyres
The wheels, valves or tyres could be damaged.
To o low a tyre pressure can lead tothe tyres
bursting. #
Examine the tyres forfo re ign objects. #
Check whe ther the tyre has a puncture
or theva lve has a leak. #
Ifyo u are unable torectify the damage,
contact a quali/ed specialist workshop. Information on
there commended tyre pressure
fo rth eve hicle's factor y-/tted tyres can be found
on the tyre pressure table on the inside of the fuel
/ller 0ap (/ page 340).
Use a suitable pressure gauge tocheck the tyre
pressure. The outer appearance of a tyre does not
permit any reliable conclusion about the tyre pres-
sure.
Only cor rect tyre pressures when the tyres are
cold. Conditions for cold tyres:
R The vehicle has been par ked with the tyres out
of direct sunlight for at least thre e hours. R
The vehicle has tr avelled less than 1.6 km.
The vehicle's tyres heat up when driving. As the
te mp erature of the tyres increases, so too does
th e tyre pressure.
V
V ehicles wit ehicles wit h a tyr
h a tyre pr
e pressur
essur e monit
e monit or
oring syst
ing syst em:
em:
yo u can also check the tyre pressure using the
on-board computer (/ page 341).
Not
Not es on tr
es on tr ailer oper
ailer oper ation
ation
Alw ays in0ate there ar axle tyres tothere com-
mended tyre pressures on the tyre pressure table
fo r increased load. T
T
yr
yr e pr
e pr essur
essur e t
e table
able The tyre pressure
table is on the inside of the fuel
/ller 0ap. The tyre pressure
table sho ws there commended
tyre pressure for all tyres appr ovedfo rth is vehi-
cle. The recommended tyre pressures apply for
cold tyres under various operating conditions, i.e.
loading and/or speed of theve hicle.
If one or more tyre sizes precede a tyre pressure,
th efo llowing tyre pressure information is only
va lid forth ose tyre sizes and their respecti veload
condition. 340
340
Wheels and tyres

If
th e preceding tyre sizes are complemented by
th e+ symbol, the tyre pressure information
fo llowing sho wsalternative tyre pressures. Fuel
consum ption may then increase slightl y.
The load conditions "pa rtially laden" and "fully
laden" are de/ned in theta ble for di.erent num-
bers of passengers and amounts of luggage. The
actual number of seats may di.er from this. T
T
yr
yr e pr
e pr essur
essur e monit
e monit or
oring syst
ing syst em
em F
F
unction of t
unction of t he tyr
he tyre pr
e pressur
essur e monit
e monit or
oring syst
ing syst em
em
The system checks the tyre pressure and the tyre
te mp erature of the tyres /t tedtotheve hicle by
means of a tyre pressure sensor.
The tyre pressure and the tyre temp erature
appear in the on-board computer (/ page 341).
If th ere is a substantial pressure loss or if the tyre
te mp erature is excessive, you will be warned with
display messages (/ page 421) ortheh
wa rning lamp in the inst rument cluster
(/ page 444).
The tyre pressure monitoring system is only an
aid. It is the driver's responsibility toset the tyre pressure
tothere commended cold tyre pressure
suitable forth e operating situation.
In most cases, the tyre pressure monitoring sys-
te m will automatically update the new refere nce
va lues aTer you ha vechanged the tyre pressure.
Yo u can, ho wever, also update there fere nce val-
ues byrestarting the tyre pressure monitoring
system manually (/ page 342).
Syst
Syst em limits
em limits
The system may be impaired or may not function
particular lyin thefo llowing situations:
R incor rect refere nce values were ta ught in
R sudden pressure loss caused byafo re ign
object penetrating the tyre, forex ample
R there is a malfunction caused byano ther radio
signal source
Chec
Chec king t
king t he tyr
he tyr e pr
e pressur
essur e wit
e with t
h the tyr
he tyr e pr
e pressure
essure
monit
monit or
oring syst
ing syst em
em
R
R eq
equir uir ements:
ements:
R The vehicle is switched on. On-board computer:
4 Service 5
Tyres
One of thefo llowing displa ysappears:
R Current tyre pressure and tyre temp erature of
th e individual wheels: R
Tyre pressures will be displayed after a few
minutes of driving
R Tyre pressure monitor active: thete ach-in
process of the system is not yetcomple te. The
tyre pressures are already being monitored. #
Compare the tyre pressure with there com-
mended tyre pressure forth e cur rent ope rat-
ing condition (/ page 340).Additionall y, Wheels and tyres
341 341

-
Athttps://be vo.mercedes-benz.com
- Inthe Mercedes-Benz BeVo App
R Ataqu ali/ed specialist workshop *
N
NOOTE
TE Overheating at high outside tempe r-
atures If an inappropriate coolant is used,
the cooling
system is not su1ciently pr otected against
ov erheating and cor rosion at high outside
te mp eratures. #
Only use coolant appr ovedfor
Mercedes-Benz. #
Obser vethe inst ructions in the
Mercedes-Benz Speci/cations for Oper-
ating Fluids 320.1. Ha
ve the coolant regula rly re placed at a quali/ed
specialist workshop.
Proportion of antif reeze concentrate in the cool-
ing system:
R A minimum of 50% (antifreeze pr otection down
to about -37°C) R
A maximum of 55% (antif reeze pr otection
down to-45°C) N
No ot
tes on windscr
es on windscr een w
een washer
asher 0uid
0uid Obser
vethe no tes on operating 0uids
(/ page 360). &
W
WARNING
ARNING ‑ Risk of /re and injury due to
windscreen washer concent rate
Wi ndsc reen washer concent rate is highly 0am-
mable. It could ignite if it comes into contact
with hot engine component parts or the
ex haust system. #
Make sure that no windscreen washer
concent rate spills out next tothe /ller
opening. *
N NOOTE
TE Damage totheex terior lighting due
to unsuitable windscreen washer 0uid Unsuitable windscreen
washer 0uids may
damage the plastic sur face of theex terior
lighting. #
Only use windscreen washer 0uids which
are also suitable for use on plastic sur fa-
ces, e.g. MB SummerFit or MB WinterFit. *
N
NOOTE
TE Bloc ked spr aynozzles caused by
mixing windscreen washer 0uids #
Do not mix MB SummerFit and MB Win-
te rFit with other windscreen washer 0u-
ids. Do not use distilled or de-ionised
water. Other-
wise, the /ll le vel sensor may be triggered er rone-
ous ly.
Re commended windscreen washer 0uid:
R abo vefreezing point: e.g. MB SummerFit
R below freezing point: e.g. MB WinterFit
Fo rth e cor rect mixing ratio, referto the informa-
tion on the antifreeze container.
Mix washer 0uid with windscreen washer 0uid all
ye ar round. 368
368
Te
ch nical data

Lights
Lights
Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/conseq uences and
uences andM
MSolutions
Solutions
:
Left dipped beam (examp le) *T
he cor responding light source is defecti ve. #
Drive on carefull y. #
Consult a quali/ed specialist workshop immediatel y.
% LED light sources: the display message forth e cor responding light appears only when all the light-emitting diodes
in the light are faulty.
: Malfunction See Owner's
Manual *T
heexterior lighting is malfunctioning. #
Consult a quali/ed specialist workshop.
*V Vehicles wit ehicles wit h a tr
h a trailer hitc
ailer hitc h:
h:a fuse may ha veblown. #
Stop theve hicle in accordance with the tra1c conditions. #
Check the fuses and replace them if necessary (/ page 334).
:
Automatic driving lights
inoperative *T
he light sensor for automatic driving lights is malfunctioning. #
Consult a quali/ed specialist workshop. 380 380
Displ
aymessages and warning/indicator lamps

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences andM
MSolutions
Solutions
:
Active Light System inoper-
ative *T
he active headlamps are malfunctioning. #
Consult a quali/ed specialist workshop.
:
Switch on headlamps *Y
ou are driving without lo w-beam headlamps. #
Turn the light switch totheL orà position.
:
Switch off lights *Y
ou are leaving theve hicle and the lights are still switched on. #
Turn the light switch totheà position.
:
Intelligent Light System
inoperative *T
he Intelli gent Light System is malfunctioning. The lighting system continues tofunction proper lywithout the functions
of the Intelligent Light System. #
Consult a quali/ed specialist workshop. Displ
aymessages and warning/indicator lamps
381
381