2022 MAZDA MODEL MX-30 EV power

depressed, the more the power meter
needle is in the POWER zone.
1. CHARGE zone
2. POWER zone
The CHARGE indicators indicate the
electrical power which can be
generated by regenerative braking, and
the POWER indicators indicate the
motor output status.
1. CHARGE indicators
2. POWER indicators
The CHARGE indicators turns off in
stages when the power generated by
regenerative braking cannot charge the
high voltage battery. The POWER
indicators turn o ff in stages when the
motor output is restricted.
When Driving
Instrument Cluster and Display
4-10
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Multi-information Display
1. Multi-information Display
2. INFO switch

The multi-information display indicates the following information.
SpeedometerOdometerTr i p m e te rOutside temperatureRemaining high voltage battery powerDistance-to-full dischargeAverage energy e
fficiencyInstantaneous energy
effi ciencyCharge status displayi-ACTIVSENSE DisplayCompass DisplayDoor-Ajar/Liftgate-Ajar Warning Indication*1
Message Display
*1 Displayed when opening door/liftgate.
When Driving
Instrument Cluster and Display
4-11
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

NOTE
When the high voltage battery
temperature is high or low, the output
may be restricted to protect the EV
system.
▼High Voltage Battery Power Gauge
The remaining power of the high
voltage battery is indicated when the
power switch is switched ON.
When the high voltage battery is fully
charged, F is indicated. As the level
lowers, the needle approaches E.
When the high voltage battery charge
decreases to 1/4 or lower, we
recommend charging the battery.

1. F (Fully charged)
2. 1/4 charged
3. E (Fully discharged)

When the remaining charge of the high
voltage battery is low, output may be
restricted. If the output is restricted,
charge the battery as soon as possible.
NOTE
After charging, it may require some
time for the needle to stabilize.
The arrow indicates that the
charging port is on the right side.
▼ Dashboard Illumination
When the lights are turned on with the
power switch switched ON, the
brightness of the dashboard
illumination is dimmed. However,
when the light sensor detects that the
surrounding area is bright such as
when the lights are turned on in the
daytime, the dashboard illumination
does not dim.
NOTE
When the power switch is switched
ON in the early evening or at dusk,
the dashboard illumination is
dimmed for several seconds until the
light sensor detects the brightness of
the surrounding area, however, the
dimming may cancel after the
brightness is detected.
When the lights are turned on, the
lights-on indicator light in the
instrument cluster turns on.
Refer to Headlights on page 4-35.
The brightness of the instrument panel
and dashboard illuminations can be
adjusted by pressing the dashboard
illumination switch while the
dashboard illumination is dimmed.
The brightness increases by pressing
the + switch.
The brightness decreases by pressing
the - switch. If you press the - switch
while the instrument cluster is at
maximum dimness, a sound is
activated to notify you that the
When Driving
Instrument Cluster and Display
4-14
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

current dimmer setting is at
maximum dimness.

1. Bright
2. Dim
Function for canceling illumination
dimmer
The illumination dimmer can be
canceled by pressing the + switch
while the instrument cluster is at
maximum dimness and while the
power switch is switched ON. If you
press the + switch again while the
illumination dimmer is canceled, a
sound is activated to notify you that it
is canceled. If the instrument cluster's
visibility is reduced due to glare from
surrounding brightness, cancel the
illumination dimmer.
NOTE
When the illumination dimmer is
canceled, the instrument cluster
cannot be dimmed even if the lights
are turned on.
When the illumination dimmer is
canceled, the screen in the center
display switches to constant display
of the daytime screen.
▼ Outside Temperature Display
When the power switch is switched
ON, the outside temperature is
displayed.

NOTE
Under the following conditions, the
outside temperature display may
di ffer from the actual outside
temperature depending on the
surroundings and vehicle conditions:
Signi ficantly cold or hot
temperatures.
Sudden changes in outside
temperature.
The vehicle is parked.The vehicle is driven at low speeds.
Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and
Fahrenheit.
Settings can be changed by operating
the center display screen.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When Driving
Instrument Cluster and Display
4-15
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Remaining High Voltage Battery
Powe r I n d i cat i o n
The remaining amount of power in the
high voltage battery is indicated by a
percentage.

▼Distance to full discharge
The remaining distance to full
discharge is calculated and displayed
based on the current, remaining charge
of the high voltage battery and the
energy
effi ciency.

NOTE
The indicated remaining
distance-to-full discharge is an
estimate. The remaining
distance-to-full discharge diff ers
depending on conditions such as the
driving conditions, surrounding
environment, and the climate control
system use. Also, if the needle in the
remaining charge level gauge for the
high voltage battery is near 0 or a
message is displayed on the
multi-information display, charge the
battery as soon as possible even if
the numerical value for the
remaining distance-to-full discharge
is of a suffi cient level.
If there is no past energy
effi ciency
information, such as after first
purchasing your vehicle or the
information was deleted when
disconnecting the lead-acid battery
terminal, the actual remaining
distance to full discharge range may
diff er from the charge level
indicated.
▼ Average Energy
Effi ciency
The average energy e fficiency is
calculated every 30 seconds from the
total traveled distance and the total
electrical power consumption since
the vehicle was purchased or the past
data was reset, and the rate is
displayed.
When Driving
Instrument Cluster and Display
4-16
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

The average energy efficiency is also
indicated by a red arrow on the
instantaneous energy e fficiency gauge.


To reset the displayed average energy
e ffi ciency data, press the INFO switch
for 1.5 seconds or longer. After
resetting the data, - - - kWh/100 km
(- - - mile/kWh) is displayed before
the average energy e fficiency is
recalculated and displayed.
▼ Instantaneous Energy
Effi ciency
The instantaneous energy e fficiency
while driving the vehicle is calculated
from the electrical power consumption
and displayed.

NOTE
Indicates the 0 position when the
vehicle speed is about 5 km/h (3
mph) or slower.
The red arrow on the scale indicates
the average energy effi ciency.
▼ i-ACTIVSENSE Display*
Displays the system status.

Refer to Lane Departure Warning
System (LDWS) on page 4-86.
Refer to Blind Spot Monitoring
(BSM) on page 4-90.
Refer to Tra
ffic Sign Recognition
System (TSR) on page 4-95.
Refer to Distance & Speed Alert
(DSA) on page 4-99.
Refer to Driver Attention Alert (DAA)
on page 4-101.
Refer to Driver Monitoring (DM) on
page 4-103.
Refer to Front Cross Traffic Alert
(FCTA) on page 4-104.
Refer to Mazda Radar Cruise Control
with Stop & Go function (MRCC
with Stop & Go function) on page
4-112.
Refer to Tra ffic Jam Assist (TJA) on
page 4-119.
Refer to Lane-keep Assist System
(LAS) on page 4-128.
Refer to Emergency Lane Keeping
(ELK) on page 4-129.
Refer to Smart Brake Support (SBS)
on page 4-136.
Refer to Cruise Control on page
4-177.
When Driving
Instrument Cluster and Display
*Some models.4-17
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Warning Indication/Warning Lights
These lights turn on or
flash to notify the user of the system operation status or a
system malfunction.
Signal Warning Refer to
Brake System Warning Indication/Warning Light*17-21
ABS Warning Indication/Warning Light*1
Electronic
Brake Force
Distribution
System Warn- ing
7-22
ABS warning 7-26
Lead-acid Battery Charging System Warning Indication/Warning
Light*17-22
EV System Problem Warning Indication/Warning Light*17-22
High Voltage Battery Temperature Warning Indication 7-23
Remaining High Voltage Battery Power Warning Indication/Warning
Light*17-23
Charging System Warning Indication/Warning Light*17-24
Output Restriction Warning Indication/Warning Light*17-24
Power Steering Malfunction Indication/Indicator Light*17-25
Shift Control System Warning Indication/Warning light*17-25
Master Warning Indication7-26
Brake Control System Warning Indication/Warning Light*17-26
Brake Override Warning Indication7-26
When Driving
Instrument Cluster and Display
4-19
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

SignalWarning Refer to
Air Bag/Front Seat Belt Pretensioner System Warning Indication/
Warning Light*17-27
Tire Pressure Monitoring System (TPMS) Warning Indication/Warning
Light*1
Flashing
7-27
Tu r n s o n 7-30
(Red) KEY Warning Indication/Warning Light
*17-28
(Amber)
*High Beam Control System (HBC) Warning Indication/Warning
Light*17-28
i-ACTIVSENSE Warning Indication/Warning Light*17-29
Exterior Light Warning Indication/Warning Light*17-29
Seat Belt Warning Indication/Warning Light (Front seat) 7-29
(Red)Seat Belt Warning Light (Rear seat)
7-30
*Low Washer Fluid Level Warning Indication/Warning Light7-30
Door-Ajar Warning Indication
7-30
Liftgate-Ajar Warning Indication7-30
Door-Ajar Warning Light 7-30
*1 The light turns on when the power switch is switched ON for an operation check, and turns o ff a few
seconds later or when the EV system is started. If the light does not turn on or remains on, have the
vehicle inspected by an Authorized Mazda Dealer.
When Driving
Instrument Cluster and Display
4-20*Some models.
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07