2022 LEXUS RX450h high beam

3TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
Trailer towing (vehicles with towing package) ......................................... 171
Dinghy towing ................................. 181
4-2. Driving procedures Power (ignition) switch ............... 182
EV drive mode ............................... 187
Hybrid transmission ..................... 189
Turn signal lever............................. 192
Parking brake ................................. 193
Brake Hold....................................... 196
4-3. Operating the lights and wipers Headlight switch ............................ 198
AHB (Automatic High Beam) ............................................................ 201
Fog light switch ............................. 204
Windshield wipers and washer ........................................................... 204
Rear window wiper and washer ........................................................... 208
4-4. Refueling Opening the fuel tank cap........ 209
4-5. Using the driving support systems Lexus Safety System + 2.0 ........ 212
PCS (Pre-Collision System)..... 218
LTA (Lane Tracing Assist)........ 225
RSA (Road Sign Assist) ............. 234
Dynamic radar crui se control with
full-speed range ......................... 236
BSM (Blind Spot Monitor) ....... 246
PKSA (Parking Support Alert) ........................................................... 250
Intuitive parking assist ................ 252
RCTA (Rear cross traffic alert) function .......................................... 259
PKSB (Parking Support Brake) ........................................................... 265Parking Support Brake function
(static objects) .............................. 271
Parking Support Brake function (rear-crossing vehicles) .......... 274
Driving mode select switch ..... 276
Driving assist systems ................ 278
4-6. Driving tips Hybrid vehicle driving tips ....... 284
Winter driving tips ....................... 286
Utility vehicle precautions........ 288
5-1. Remote Touch/Display Remote Touch................................ 292
Center Display.............................. 294
5-2. Lexus Climate Concierge Lexus Climate Concierge........ 297
5-3. Using the air conditioning system and defogger
Front automatic air conditioning system ............................................ 298
Rear automatic air conditioning system ............................................ 309
Heated steering wheel/seat heat- ers/seat ventilators..................... 312
5-4. Using the interior lights Interior lights list ............................ 315
5-5. Using the storage features List of storage features ............... 318
Luggage compartment features .......................................................... 324
5-6. Using the other interior features Other interior features .............. 329
Garage door opener ................... 341
Compass ......................................... 346
5Interior features

16Pictorial index
■Switches
Automatic High Beam switch..............................................................................P.201
Power back door switch......................................................................................... P.115
HUD (Head-up display) switch
*1.......................................................................... P.96
Fuel filler door opener switch..............................................................................P.210
Instrument panel light control switches .............................................................P.87
“ODO TRIP” switch .................................................................................................P.87
Camera switch
*1, 2
Heated steering wheel switch*1..........................................................................P.312
*1: If equipped
*2: Refer to “NAVIGATION AND MULT IMEDIA SYSTEM OWNER’S MANUAL”.
A
B
C
D
E
F
G
H

802-1. Instrument cluster
*1: These lights turn on when the power switch is turned to ON mode to indi-
cate that a system check is being per-
formed. They will turn off after the
hybrid system is on, or after a few sec-
onds. There may be a malfunction in a
system if a light does not come on, or
turn off. Have the vehicle inspected by
your Lexus dealer.
*2: This light illuminates on the multi-infor-mation display.
*3: Except F SPORT models: This light illu-minates on the multi-information dis-
play.
F SPORT models: This light illuminates
on the meter.
*4: This light illuminates on the center panel.
The indicators inform the driver of the operating state of the vehicle’s various
systems.
(flashes)
(Canada)
Parking brake indicator
( P.416)
(flashes)
Brake hold operated indicator*1
( P.417)
Master warning light
*1 ( P.417)
WARNING
■If a safety system warning light does
not come on
Should a safety system light such as the
ABS and SRS warning lights not come on
when you start the hybrid system, this
could mean that these systems are not
available to help protect you in an acci-
dent, which could result in death or seri-
ous injury. Have the vehicle inspected by
your Lexus dealer immediately if this
occurs.
Indicators
Turn signal indicator ( P.192)
(U.S.A.)
Headlight indicator (P.198)
(Canada)
Tail light indicator ( P.198)
Headlight high beam indicator
( P.199)
Automatic High Beam indica-
tor
*1 (  P.201)
Fog light indicator (if equipped)
( P.204)
PCS warning light
*1, 2
( P.220)
Cruise control indicator
( P.243)
Dynamic radar cruise control
indicator ( P.236)
Cruise control “SET” indicator
( P.236)
(white)
LTA indicator ( P.229)
(green)
LTA indicator (P.229)
(orange)
(flashes)LTA indicator ( P.229)
BSM outside rear view mirror
indicators
*3, 4 (if equipped)
( P.246, 259)
BSM indicator (if equipped)
( P.246)

161
4
4
Driving
Driving
.4-1. Before drivingDriving the vehicle ..................... 162
Cargo and luggage ................... 167
Vehicle load limits ...................... 170
Trailer towing (vehicles without towing package) ....................... 171
Trailer towing (vehicles with tow- ing package)............................... 171
Dinghy towing .............................. 181
4-2. Driving procedures Power (ignition) switch ............ 182
EV drive mode ............................ 187
Hybrid transmission .................. 189
Turn signal lever.......................... 192
Parking brake .............................. 193
Brake Hold.................................... 196
4-3. Operating the lights and wipers Headlight switch ......................... 198
AHB (Automatic High Beam) ......................................................... 201
Fog light switch .......................... 204
Windshield wipers and washer ........................................................ 204
Rear window wiper and washer ........................................................ 208
4-4. Refueling Opening the fuel tank cap..... 209
4-5. Using the driving support sys- tems
Lexus Safety System + 2.0 ..... 212PCS (Pre-Collision System)
........................................................ 218
LTA (Lane Tracing Assist) .... 225
RSA (Road Sign Assist).......... 234
Dynamic radar cruise control with full-speed range...................... 236
BSM (Blind Spot Monitor) .... 246
PKSA (Parking Support Alert) ....................................................... 250
Intuitive parking assist ............. 252
RCTA (Rear cross traffic alert) function....................................... 259
PKSB (Parking Support Brake) ....................................................... 265
Parking Support Brake function (static objects) ........................... 271
Parking Support Brake function (rear-crossing vehicles) ...... 274
Driving mode select switch .. 276
Driving assist systems.............. 278
4-6. Driving tips Hybrid vehicle driving tips .... 284
Winter driving tips .................... 286
Utility vehicle precautions..... 288

1994-3. Operating the lights and wipers
4
Driving
Doing so interferes with the sensor detect-
ing the level of ambient light and may cause
the automatic headlight system to malfunc-
tion.
■Automatic light off system
●When the headlights are on: The head-
lights and tail lights turn off 30 seconds
after the driver’s door is opened and
closed if the power switch is turned to
ACCESSORY mode or turned off. (The
lights turn off immediately if on the
key is pressed after all the doors are
closed.)
●When only the tail lights are on: The tail
lights turn off automatically if the power
switch is turned to ACCESSORY mode
or turned off and the driver’s door is
opened.
■Automatic headlight leveling system (if
equipped)
The level of the headlights is automatically
adjusted according to the number of pas-
sengers and the loading condition of the
vehicle to ensure that the headlights do not
interfere with other road users.
■Light reminder buzzer
A buzzer sounds when the power switch is
turned off or turned to ACCESSORY
mode and the driver’s door is opened while
the lights are turned on.
■Welcome lighting
If the headlight switch is turned to and
the surrounding area is dark, unlocking the
doors using the smart access system with
push-button start or wireless remote con-
trol will turn the parking lights and tail lights
on automatically.
■Windshield wiper linked headlight illu-
mination
When driving during daytime with the
headlight switch turned to , if the wind-
shield wipers are used, the headlights will
turn on automatically after several seconds
to help enhance the visibility of your vehicle.
■12-volt battery-saving function
In order to prevent the 12-volt battery of the vehicle from discharging, if the headlights
and/or tail lights are on when the power
switch is turned off
the 12-volt battery sav-
ing function will operate and automatically
turn off all the lights after approximately 20
minutes. When the power switch is turned
to ON mode, the 12-volt battery-saving
function will be disabled.
When any of the following are performed,
the 12-volt battery-saving function is
canceled once and then reactivated. All the
lights will turn off automatically 20 minutes
after the 12-volt battery-saving function has
been reactivated:
●When the headlight switch is operated
●When a door is opened or closed
■Customization
Some functions can be customized.
( P.472)
1 With the headlights on, push the
lever away from you to turn on the
high beams.
Pull the lever toward you to the center
position to turn the high beams off.
2Pull the lever toward you and
release it to flash the high beams
NOTICE
■To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the hy brid system is off.
Turning on the high beam head-
lights

2004-3. Operating the lights and wipers
once.
You can flash the high beams with the
headlights on or off.
AFS (Adaptive Front-lighting System)
secures excellent visibility at intersec-
tions and on curves by automatically
adjusting the direction of the light axis
of the headlights according to vehicle
speed and the degree of the tire’s angle
as controlled by steering input.
AFS operates at speeds of 6 mph (10
km/h) or higher.
■Customization
Some functions can be customized.
(  P.472)
 When the steering wheel or turn
signal lever is operated while the
headlights are on (low beam), a cor-
nering light will turn on and light up
the direction of movement of the
vehicle. The cornering lights are
designed to ensure excellent visibil-
ity when making a turn at an inter-
section.
However, when vehicle speed is approxi-
mately 22 mph (35 km/h) or higher, the
cornering lights will not turn on.
 When the shift lever is in R while the
headlights are on (low beam), both
cornering lights will turn on. This is
designed to enhance visibility when
parking.
■Cornering lights (if equipped)
When the cornering lights are on for more
than 30 minutes, they will turn off automati-
cally.
AFS (Adaptive Front-lighting
System) (if equipped)
Cornering lights (if equipped)

2014-3. Operating the lights and wipers
4
Driving
1Press the Automatic High Beam
switch.
2 Turn the headlight switch to the
or position.
The Automatic High Beam indicator will come on when the system is operating.
■Conditions to turn the high beams on/off
automatically
●When all of the follo
wing conditions are
met, the high beams will be turned on
automatically (after approximately 1 sec-
ond):
• The vehicle speed is approximately 21 mph (34 km/h) or more.
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with head- lights or tail lights turned on.
• There are few streetlights on the road ahead.
●If any of the following conditions is met,
the high beams will turn off automatically:
• The vehicle speed is below approxi-
mately 17 mph (27 km/h).
• The area ahead of the vehicle is not dark.
• Vehicles ahead have their headlights or tail lights turned on.
• There are many streetlights on the road ahead.
■Camera sensor dete ction information
●The high beams may not be automatically
turned off in the following situations:
• When a vehicle suddenly appears from around a curve
• When the vehicle is cut in front of by
another vehicle
• When vehicles ahead cannot be detected due to repeated curves, road
dividers or roadside trees
• When vehicles ahead appear in a far- away lane on a wide road
• When the lights of vehicles ahead are not
on
●The high beams may be turned off if a
vehicle ahead that is using fog lights with-
AHB (Automatic High
Beam)
The Automatic High Beam uses a
camera sensor located behind the
upper portion of the windshield to
assess the brightness of the lights of
vehicles ahead, streetlights, etc.,
and automatically turns the high
beams on or off as necessary.
WARNING
■Limitations of the Automatic High
Beam
Do not overly rely on the Automatic High
Beam. Always drive sa fely, taking care to
observe your surroundings and turning
the high beams on or off manually if nec-
essary.
■To prevent incorrect operation of the
Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic High
Beam

2024-3. Operating the lights and wipers
out its headlights turned on is detected.
●House lights, street lights, traffic signals,
and illuminated billboards or signs and
other reflective objects may cause the
high beams to change to the low beams,
or the low beams to remain on.
●The following factors may affect the
amount of time taken for the high beams
to turn on or off:
• The brightness of the headlights, fog
lights, and tail lights of vehicles ahead
• The movement and direction of vehicles ahead
• When a vehicle ahead only has opera- tional lights on one side
• When a vehicle ahead is a two-wheeled
vehicle
• The condition of the road (gradient, curve, condition of th e road surface, etc.)
• The number of passengers and amount of luggage in the vehicle
●The high beams may turn on or off unex-
pectedly.
●Bicycles or similar vehicles may not be
detected.
●In the following situations the system may
not be able to correctly detect the sur-
rounding brightness level. This may cause
the low beams to remain on or the high
beams to flash or dazzle pedestrians or
vehicles ahead. In such a case, it is neces-
sary to manually switch between the high
and low beams.
• When driving in inclement weather
(heavy rain, snow, fo g, sandstorms, etc.)
• When the windshield is obscured by fog, mist, ice, dirt, etc.
• When the windshield is cracked or dam- aged
• When the camera sensor is deformed or
dirty
• When the temperature of the camera sensor is extremely high
• When the surrounding brightness level is equal to that of head lights, tail lights or
fog lights
• When headlights or tail lights of vehicles
ahead are turned off, dirty, changing
color, or not aimed properly
• When the vehicle is hit by water, snow,
dust, etc. from a preceding vehicle
• When driving through an area of inter- mittently changing brightness and dark-
ness
• When frequently and repeatedly driving
ascending/descending roads, or roads
with rough, bumpy or uneven surfaces
(such as stone-paved roads, gravel roads,
etc.)
• When frequently and repeatedly taking curves or driving on a winding road
• When there is a highly reflective object ahead of the vehicle, such as a sign or
mirror
• When the back of a preceding vehicle is highly reflective, such as a container on a
truck
• When the vehicle’s headlights are dam- aged or dirty, or are not aimed properly
• When the vehicle is listing or titling due to
a flat tire, a trailer being towed, etc.
• When the headlights are changed between the high beams and low beams
repeatedly in an abnormal manner
• When the driver believes that the high beams may be flashing or dazzling
pedestrians or other drivers
■Temporarily lowering sensor sensitivity
The sensitivity of the sensor can be tempo-
rarily lowered.
1 Turn the power switch off while the fol-
lowing conditions are met.
●The headlight switch is in or .
●The headlight switch lever is in high beam
position.
●Automatic High Beam switch is on.
2 Turn the power switch to ON mode.
3 Within 60 seconds after step 2, repeat
pulling the headlight switch lever to the
original position then pushing it to the
high beam position quickly 10 times,
then leave the lever in high beam posi-
tion.
4 If the sensitivity is changed, the Auto-
matic High Beam indicator is turn on
and off 3 times.
Automatic High Beam (headlights) may
turn on even when th e vehicle is stopped.