2022 KIA TELLURIDE light

See section 4 in the Owner’s Manual for more information .
STEERING WHEEL
CONTROLS
STEERING WHEEL CONTROLS
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED33
Headlight position
Parking Light position
AUTOAuto Light /DRL/ High Beam Assist*
OFFOFF position
To operate front wipers & washers:
•Move lever up/down to change wiper modes
MIST: Single wipe LO: Slow wipeOFF: Wiper off HI: Fast wipeINT*/AUTO*: Intermittent*/Auto Rain Sensing*
•Pull to spray and wipe
To operate rear wipers & washers:
•Rotate Rear Wiper switch to change Wiper modes
•Push lever to spray and wipe
Auto Rain Sensing (Auto Control)*
The rain sensor located on the upper end of the windshield glass is designed to sense the amount of rainfall and control the wiping cycle for the proper interval . The more it rains, the faster the wiper operates . When the rain stops, the wiper stops .
To turn ON the auto rain sensing wipers, move lever up/down to AUTO . To adjust the auto rain sensing wiper speed setting, move the speed control switch A up/down .
Auto Rear Wiper* – The feature can be enabled in the User Settings on the Instrument Cluster . When the lever is in the AUTO position, the gear shift is moved into Reverse (R), Auto Rear Wiper activates and will wipe the rear windshield .
Front & Rear Windshield Wipers & Washers
HI
LO
OFF
"
#
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wipers and Wiper Stalk Video
QR CODE
CImage for illustrative purposes only . See section 7 in the Owner’s Manual for more information .
To lift the windshield wipers to clean the windshield, inspect or replace wiper blades or raise the wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the middle of the windshield (service position) C .
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch up to the MIST position B and hold the switch for more than two seconds until the wiper blade is in the fully up position .
To return wipers to the normal position, turn the ignition ON, then activate MIST .
Lifting Wipers/Winter Mode (Wiper Service Mode)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wiper Service ModeVideo
QR CODE
MIST: Single wipe
OFF: Wiper off
LO: Slow wipe
HI: Fast wipe
INT*/AUTO: Intermittent*/Auto/Rain Sensing*
•When the Engine Star t/Stop but ton is in the ON position and the wiper switch is in AUTO mode, the wiper will automatically operate once to per form a self-check of the system
•Set the wiper to the OFF position when the wiper is not in use
•Moving lever to HI increases intermit tent wipe frequency and wipe speed . Moving lever to LO decreases frequency of wipes
•Pressing but ton A up increases Intermit tent wipe frequency and wipe speed . Pressing but ton A down decreases frequency of wipes
•On Rear Wipers, intermit tent wipe function is not adjustable
QUICK TIPS

AUDIO SYSTEMS
AUDIOSYSTEMS
Android Auto™
Setting up Android Auto™:
1 . From an Android Auto™ compatible device, download the Android Auto™ app from the Google Play™ Store†3
2 . Open the Android Auto™ app and proceed with the onscreen instructions to complete setup on the mobile device
How to start Android Auto™:
1 . Press the SETUP key on your audio head unit ’s control panel
2 . Press the PHONE PROJECTION or DEVICE CONNECTION button, select Android Auto™ then select ENABLE ANDROID AUTO . Review all terms, conditions and requests on the head unit and phone, and, if you agree, accept them in order to use Android Auto™
3 . Connect the Android™ device with the vehicle’s USB port using the manufacturer ’s cable provided with your phone
4 . From the vehicle’s home screen, select the Android Auto™ button, where you’ll see all the Android Auto™ supported apps
Apple CarPlay®
Setting up and starting Apple CarPlay®:
1 . On the head unit, press the SETUP key
2 . Press the PHONE PROJECTION or DEVICE CONNECTION button, select Apple CarPlay® then select ENABLE APPLE CARPL AY . Review all terms, conditions and requests on the head unit and phone, and, if you agree, accept them in order to use Apple CarPlay®
3 . Connect the Apple CarPlay® compatible iPhone®†3 with the vehicle’s Multimedia USB port using the manufacturer ’s cable provided with your iPhone®
4 . From the vehicle’s home screen, select the Apple CarPlay® button, where you’ll see all the Apple CarPlay® supported apps
Android AutoTM†3 / Apple CarPlay® Setup†3
Driving while distracted can result in a loss of vehicle control that may lead to an accident, severe bodily injury, and death . The driver’s primary responsibility is in the safe and legal operation of a vehicle, and any handheld devices, other equipment, or vehicle systems which take the driver’s eyes, attention and focus away from the safe operation of a vehicle or which are not permissible by law should never be used during operation of the vehicle .
Refer to the Car Infotainment System Quick Reference Guide for more information . For audio system information, refer to pages 35-40 .
REMINDERS:
•
Android Auto™ compatibilit y requirements: Micro-USB cable that came with your phone, OS Android™ 5 .0 or higher, compatible Android™ smar tphone and data and wireless plan for applicable feature(s)
•
Apple CarPlay® compatibilit y requirements: Apple Lightning® cable, latest iOS soft ware (above iOS 10) and data and wireless plan for applicable feature(s)
•
It is recommended to always update your phone to the latest operating system release
•
Using an approved USB cable provided by your smar tphone manufacture is recommended
•
Using unapproved USB cables may cause a phone projection error or a system malfunction, black screen, no sound, disconnection, etc .
•Phone projection may not work due to a defect in the phone
•
Driving while distracted can result in a loss of vehicle control that may lead to an accident, severe bodily injur y, and death . The driver ’s primar y responsibilit y is in the safe and legal operation of a vehicle, and any handheld devices, other equipment, or vehicle systems which take the driver ’s eyes, at tention and focus away from the safe operation of a vehicle or which are not permissible by law should never be used during operation of the vehicle
•If Android Auto™ / Apple CarPlay® randomly disconnects:
•Ensure the USB cable is cer tified by the phone manufacture for both power and data
•Clean the phones por t, which the USB cable connects to, with disposable compressed air
•
The Phone should not be disturbed while driving as this can cause a disconnection at the phone’s USB por t
•Visit the phone manufactures website for Android Auto™ / Apple CarPlay® app concerns
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED38TELLURIDE FEATURES & FUNCTIONS GUIDE

CENTER PANEL
CENTER PANEL
*IF EQUIPPED42TELLURIDE FEATURES & FUNCTIONS GUIDE
Press the SETUP key on the audio head unit, then press the GENER AL button then date/time button to enter the clock settings . Then use the onscreen buttons to navigate through setup and return to exit .
REMINDERS:
•
Daylight Saving must be enabled or disabled in the Clock Set tings screen
•To access manual date and time set ting, turn GPS Time OFF in the Clock Set tings (UVO link with Navigation*)
Refer to the Car Infotainment System Quick Reference Guide for more information .
Clock
The AC Inverter supplies 115V/100W electrical power to operate accessories or equipment . Press the AC Inverter button to activate .
AC Inverter*
(Located behind center console)
See section 4 in the Owner’s Manual for more information .
•The power outlets are inactive when the ignition is in the OFF position
•The Multimedia USB data por t is located next to the Power Outlets A
•USB Charger does not suppor t data transfer
QUICK TIPS
REMINDERS:
•
Using the power outlets (accessor y plugs) for prolonged periods of time with the Engine Star t/Stop but ton in the ACC position (Engine OFF) may cause the bat ter y to discharge
•Only use manufacturer cables that came with your device as third par t y cables may cause damage to the device
•The Multimedia USB Por t B in the center panel charges more slowly than the USB Chargers C throughout the vehicle
Power Outlets A : Use the power outlets for mobile phones and other devices designed to operate on a 12V (180W max) power outlet .
Multimedia USB Port B : Use the USB port to connect USB audio devices and smartphone devices .
USB Charger Ports C : Devices can be recharged using a USB cable . The Engine Start/Stop button needs to be in the ACC/ON/START position to operate the USB Charger .
12V180WUSB
(Located in center panel in front of gearshift)
Multimedia USB Ports, Power Outlets & USB Charger Ports
CBA
See section 4 in the Owner’s Manual for more information .

CENTER PANEL
CENTER PANEL
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wireless Charging Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED43
•For wireless charging to occur, all doors (excluding rear hatch) must be closed and the Smar tKey Fob must be detected inside the vehicle
•For best results, place the smar tphone on the center of the charging pad
•If wireless charging does not work, move the smar tphone around the pad until the charging indicator turns amber
•Avoid placing other metal items in the bin while charging as to not impede the charging area
QUICK TIPS
REMINDERS:
•If any door is opened, charging will be disabled
•The smar tphone must be a compatible phone with QI function available
•Avoid placing other metal items in the bin while charging as to not impede the charging area
•
This vehicle is equipped with wireless charging technology which allows for a device to be charged using inductive charging; however, device compatibilit y varies . See the Owner ’s Manual for more detailed information and the back page for legal disclaimers
•
Inductive charging systems are less ef ficient than conventional charging through cable . As a result, higher device operating temperatures may be experienced during use
•
Charging Per formance – Your device’s position on the wireless charging system can affect charging per formance . Other factors that may affect the charging rate includes foreign objects, such as coins or pens, and phone case thickness
CB
A
Wireless Smartphone Charging System*
1 .
Enable Wireless Charging in the User Settings mode, select Convenience then Wireless Charging System
2 . Lift open the tray cover (center console, in front of gear shift) A
3 .
Place a compatible smartphone on the center of the charging pad B
4 .
The indicator light C may change to amber once wireless charging begins
5 .
Once charging is complete, the amber light C may change to green
See section 4 in the Owner’s Manual for more information .

SHIFT
LOCK
RELEASE
P•R•N•D•
+
•-
SHIFT
LOCK
RELEASE
P•
R•
N•
D•
+
•
-
CENTER PANEL
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED45
B
•
The instrument cluster and the light beside the shift lever identifies the gear the vehicle is currently in
•Press brake pedal and depress release but ton to move gear shift from N to P, N to R or from P to any gear
•Manual mode downshifts are made automatically when the vehicle slows down . When the vehicle stops, 1st gear is automatically selected
QUICK TIPSREMINDERS:
•
When in P (Park), if the Release but ton is not pressed while shifting, the transmission does not shift
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the power liftgate lid control, turn off the auto rain sensing wipers and fold in the mirrors
CENTER PANEL
See section 5 in the Owner’s Manual for more information .
To shift into any gear from Park, depress the brake pedal, then press the Release button A, located on the side of the gear shift lever, and shift .
P: Park – To shift into Park from any gear, press the Release button B on the gear shift while the vehicle is stationary and the brake pedal is depressed, and shift .
R: Reverse – To shift into Reverse, depress the brake pedal, press the Release button A, and move the shift lever into Reverse .
N: Neutral
D: Drive
[+]: Manual Mode Upshift
[–] : Manual Mode Downshift
Manual Mode: To enter the Manual mode, move the shift lever from D to the left gate B .
To shift while in Manual mode, move the shift lever up [+] to upshift or down [–] to downshift B .
Automatic Transmission and Manual Mode
A

CENTER PANEL
See section 5 in the Owner’s Manual for more information .
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED47
CENTER PANEL
REMINDERS:
•
As a bulb check, the EPB malfunction indicator will illuminate for approximately 3 seconds when the ignition switch is turned ON
•
If the warning light does not illuminate temporarily or remains continuously lit, take your vehicle to an authorized Kia dealer and have the system checked
•
The EPB should not be operated while the vehicle is moving
•
A click or electric brake motor sound may be heard while operating or releasing the EPB . These conditions are normal and indicate that the EPB is functioning properly
The Electronic Parking Brake (EPB) system utilizes an electric motor to engage the parking brake .
Applying the Parking Brake
Depress the brake pedal and pull up the EPB switch A . Ensure that the indicator light is illuminated on the instrument cluster .
Releasing the Parking Brake
The EPB will automatically release when the shifter is placed in Reverse or Drive . To release EPB manually, depress the brake pedal, then press the EPB switch A , with the ignition switch in the ON position . Ensure that the indicator light is OFF .
Electronic Parking Brake (EPB)
•Pull up and hold the EPB switch again to increase brake pressure if parked on a decline or incline
•When leaving your keys with parking lot at tendants or valet, make sure to inform them how to operate the EPB
•If parked on a steep incline, pull up the EPB switch for more than 3 seconds for a firmer EPB application vehicle slows down . When the vehicle stops, 1st gear is automatically selected
QUICK TIPS
A
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electric Parking Brake / Auto Hold Video
QR CODE

OTHER KEY FEATURES
OTHER KEY

FEATURES
Smart Power Liftgate*† 16 (continued)
See section 4 in the Owner’s Manual for more information .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Kia Smart & Folding Key Fobs Video
QR CODE
E
•The liftgate must be unlocked before it can be opened by the liftgate Release but ton
•The liftgate unlocks automatically and then can be opened manually when the Smar t Key is within close proximit y to the vehicle
QUICK TIPS
REMINDERS:
•
Smar t Power Liftgate may be damaged if at tempting to open or close manually
•When not in use, keep the Liftgate Lid Control but ton in the OFF position
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the Smar t Power Liftgate lid control using the but ton inside the glove compar tment, turn off the auto rain-sensing wipers and fold in the mirrors
•
Ensure all obstacles are out of the way of the liftgate lid when operating the Smar t Power Liftgate
•The default liftgate opening/closing speed is set to fast
•
The liftgate opening/closing speed set ting cannot be changed when the Power Liftgate function is turned off or if the liftgate is not completely closed
Opening with no-touch activation:
When the Smart Key fob is on your person and you are near the back of the
vehicle, within close proximity, the hazard lights will blink and a chime will sound for about 3 seconds as an alert that the Smart Power Liftgate* is about to open .
Then the alert system will blink and chime two additional times before opening the Smart Power Liftgate* .
The Smart Power Liftgate* feature is OFF by default . To enable the Smart Power Liftgate*, go to User Settings in the LCD Instrument Cluster modes .
Smart Key:
To open the Smart Power Liftgate*, press and hold the Smart Key Liftgate button E until the Liftgate begins opening . Press again and hold to close .
Power Liftgate Height Adjustment:
For your convenience, the liftgate opening height is adjustable . To program the opening height, per form the following:
1 . Open liftgate and manually position the liftgate to your preferred opening height
2 . Depress and hold the close button on the liftgate for 3 seconds or more
3 . Once the system sounds the alert that the programming is complete, manually close the liftgate
Power Liftgate Opening/Closing Speed Setting:
Go to the User Settings in the Instrument Cluster . Select Door, then Power Liftgate Speed, and select Fast or Normal .
HOLDHOLD
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED57

UVO
FRONTREAR
ONOFFDOOR
Automatic Turn Off Function
The interior lights automatically turn off approximately 20 seconds after the Engine Start/Stop button is
turned OFF
.
Map/Room Lamp Operation
Map Lamps – These lights produce spot beams for convenient use as map lamps or as personal lamps for the driver or the front passenger . Press the buttons A to turn the map lamps ON/OFF .
Room button – Press the button B to turn the front and rear lamps ON/OFF .
Door button – When the Door button C is pressed the front and rear lamps will turn ON as follows:
•When a door is opened or doors are unlocked with the Smart Key, the lamps will turn ON for approximately 30 seconds
•If the Engine Start/Stop button is in the ACC/OFF position and a door is open, the lamps will stay ON for approximately 20 minutes
•If the Engine Start/Stop button is in the ACC/ON position and a door is open, the lamps will stay ON
The lamps will turn OFF immediately if the Engine Start/Stop button is turned ON or all doors are locked .
OTHER KEY FEATURES
Map/Room Lamps
See section 4 in the Owner’s Manual for more information .
*IF EQUIPPED58TELLURIDE FEATURES & FUNCTIONS GUIDE
A
BC
A
OTHER KEY

FEATURES
•
When doors are unlocked by the Smar t Key, the lamp turns ON for approximately 30 seconds
•
If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 3 seconds after the system is in armed stage
•
Using interior lights for an extended period of time may cause bat ter y discharge
QUICK TIPS
REMINDER: When room lamp lens is pressed ON it will remain ON, even when the map lamp switch is in the OFF position .
(Overhead lamp console)