2022 KIA TELLURIDE engine

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED21
Lane Following Assist is designed to help ensure that the vehicle stays centered in its lane A by monitoring the detected lane markings ahead and adjust the steering . When driving, LFA can be switched on and off
by pressing the Driving Assist button B . When turned on, the instrument cluster indicator will initially illuminate white when turned ON . It will remain white when the system does not detect the lane markers . When LFA detects the lane markers and can assist the steering, the LFA icon will illuminate green C .
LFA will operate only when these conditions are met:
•LFA recognizes both sides of the lane markers the vehicle is traveling in
•The vehicle is traveling slower than 120 mph
LFA User Settings:
•
To go to User Settings in the Instrument Cluster, press the Mode button D on the Steering Wheel when the vehicle is at a standstill, gear shift is in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To enable LFA , when in User Settings, press the Move (OK) button E up/down and Select Driver Assistance then Driving Assist, and select Lane Following Assist . Press the OK button E
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings
•
Some vehicles have a Lane Driving Assist / Lane Safety button* on the Driver ’s Panel or the Steering Wheel B . Press to activate Lane Following Assist
Lane Following Assist (LFA)†4
Images are for illustrative purposes only and may not reflect actual feature or operation .
LFA is supplemental . Do not solely rely on this system and always pay attention to the road and its conditions .
See section 5 in the Owner’s Manual for more detailed information, limitations and conditions .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Lane Following Assist (LFA) Video
QR CODE
A
C
REMINDER: LFA is not a substitute for safe and proper driving . Always drive safely and use caution .
CRUISE
CANCEL
RES
OK SET
(But ton layout on right of steering wheel)
D
E
B

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED23
Rear View Monitor (RVM)†4
Rear View Monitor is a supplemental system that displays the view behind the vehicle through the Navigation screen* while the vehicle is in Reverse .
Rear View Monitor activates when the:
•Engine Start/Stop button is in the ON position
•Gear Shift Lever is in the R (Reverse) position
REMINDERS:
•
Rear View Monitor is not a substitute for proper and safe backing-up procedures
•
Rear View Monitor may not display ever y object behind the vehicle
•
Always drive carefully and use caution when backing up
•
Through normal use and after inclement weather or washing, the rear camera may become dir t y . Use a clean, microfiber cloth to remove any dir t, debris or spots that may have accumulated on the lens
•
While the Rear View Monitor is active the volume will be lowered on all audio modes
See section 4 in the Owner’s Manual for more information . Images are for illustrative purposes only and may not reflect actual feature or operation .P
R
N
DSHIFTL OCK
RELEASE

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED25
CRUISE
MODE
CRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
MODE CRUISE
CANCEL
RES
OK SET
MODE
CANCEL
RES
OK SET
MODECRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
Watch for traffic
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) is designed to warn the driver under certain conditions . It may activate the Electronic Stability Control (ESC) and temporarily apply braking if it detects cross traffic
approaching the vehicle when the vehicle is in reverse .
When the RCCA rear-corner radar sensors detect approaching vehicles from the rear left or rear right side of the vehicle A, RCCA will sound a warning, the warning indicators on the outside rearview mirror will illuminate and a message will appear on the Instrument Cluster LCD B and the audio head unit .* If RCCA detects that the collision risk has increased, RCCA automatically applies the brakes to reduce your speed, potentially helping to minimize the effects of a possible collision .
RCCA is designed to operate under the following conditions:
•When the gear shift is in Reverse
•When the vehicle is moving slower than 6 mph
RCCA User Settings:
•To go to the User Settings menu in the Instrument Cluster, press the Mode button C on the Steering Wheel when the vehicle is at a standstill, gear shift in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To turn RCCA on when in User Settings , press the Move (OK) button D up/down, select Driver Assistance, Parking Safety, Rear Cross-Traffic Safety and then press OK D
•
To set the warning timing, go to User Settings , press the Move (OK) button D up/down, then go to Driver Assistance, Warning Timing and press the OK button D
•Select one of the settings:
–
Early/Normal/Standard: Maximizes the amount of distance between the vehicles before the initial warning occurs
– L a t e : Reduces the amount of distance between the vehicles before the initial warning occurs
•The default Warning Timing is set to Normal . If the Warning Timing is changed, the warning time of other Driver Assistance systems may also change
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings
Rear Cross-Traffic Collision-Avoidance Assist (RCCA)†4
See section 5 in the Owner’s Manual for more information .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) Video
QR CODE
A
B
C
D
REMINDERS:
•
The RCCA feature can be activated or deactivated in User Set tings, under Driver Assistance, Parking Safet y
•
When vehicle power is cycled, RCCA will remain in the previous state
•
When a vehicle is approaching within the sensing range, and traveling faster than 3 mph, the RCCA system will show a warning
•
RCCA is a supplemental system . Do not solely rely on this system and always pay at tention to the road and its conditions
•RCCA Warning Volume can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings on the audio head unit . Go to Driver Assistance, then Warning Volume
QUICK TIP
(But ton layout on right of steering wheel)

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED26TELLURIDE FEATURES & FUNCTIONS GUIDE
Forward/Reverse Parking Distance Warning (PDW)†4
PDW A is a supplemental system that is designed to assist the driver by chiming if an object is detected within the sensing areas in the front or rear of the vehicle when parking or backing up .
When the Engine Start/Stop button is ON and the shift lever is in R (Reverse), PDW is activated and the PDW button indicator is illuminated .
(Rear sensors shown)
Forward*/Reverse Parking Distance Warning is not a substitute for proper and safe backing-up procedures . Always drive safely and use caution when backing up . Forward*/Reverse Parking Distance Warning (PDW) may not detect every object in front of or behind the vehicle .
See section 4 in the Owner’s Manual for more information .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Forward/Reverse Parking Distance Warning (PDW) Video
QR CODE
REMINDERS:
•
If the vehicle is moving at speeds over 6 mph, the system may not activate
•
When more than t wo objects are sensed at the same time, the closest one will be recognized first
•
PDW is not a substitute for proper and safe backing-up procedures . Always drive safely and use caution when backing up . PDW may not detect ever y object behind or in front of the vehicle
A
(But ton below gear shift oncenter console)

†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED28TELLURIDE FEATURES & FUNCTIONS GUIDE
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electronic Stability Control Video
QR CODE
REMINDERS:
•
ESC is active by default at vehicle star tup . When ignition is cycled, ESC will turn ON again
•
The ESC indicator light in the instrument cluster will be lit momentarily whenever ESC is active
REMINDERS:
•
HAC does not operate when the gear shift is in P (Park) or N (Neutral) position
•
HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
•
In the event of HAC system malfunction, see an Authorized Kia Dealer for ser vice
•When HAC is active (e .g ., during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator
•HAC provides a t wo-second delay before the vehicle may star t rolling backwards
QUICK TIPS
Electronic Stability Control (ESC)†6 /
Traction Control System (TCS)†6
Electronic Stability Control (ESC) is designed to help stabilize the vehicle during certain cornering maneuvers . The Traction Control System (TCS) can help improve traction . It is a good idea to keep both ESC and TCS turned on for daily driving whenever possible .
Press the ESC button B to turn the Traction Control System OFF/ON .
To turn both Electronic Stability Control and the Traction Control System OFF, press and hold the ESC button for more than 3 seconds . Press again to turn ON .
Instrument Cluster Control (Instrument Panel Dimmer)
With the Engine Start/Stop button on or the parking lights/headlights on, press A (+) or (-) to adjust the brightness of the instrument panel illumination .
(But ton located on driver ’s panel, left of the steering wheel)
See section 4 in the Owner’s Manual for more information .
See section 5 in the Owner’s Manual for more information .
See section 5 in the Owner’s Manual for more information .
Hill-Start Assist Control (HAC)†6
Hill-Start Assist Control (HAC) is designed to prevent the vehicle from rolling backwards when accelerating from a stop while on a steep incline .
HAC automatically activates whether ESC is OFF or ON but does NOT activate when ESC has malfunctioned .
AB
DRIVER’S PANEL
DRIVER’S PANEL

ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED29
DRIVER’S PANEL
DRIVER’S PANEL
REMINDER: When the but tons are not pressed, the Reverse Parking Aid Function will not operate and the outside rear view mirrors will not rotate downward .See section 4 in the Owner’s Manual for more information .
For illustrative purposes only . Your actual display, buttons and/or features may vary .
Reverse Parking Aid Function†4
When the gear shift lever is moved into R (Reverse) and the vehicle is moving backwards, the outside rearview mirrors will rotate downward to aid in reverse parking .
To turn Reverse Parking Aid Function ON, move switch A to either the right or to the left . To turn OFF, move switch to the center position .
The outside rearview mirrors will automatically return to their original positions when:
•The Engine Start/Stop button is in the OFF position
•The gear shift lever is moved out of R (Reverse)
•
The outside rearview mirror switch is in the center position
R
L
A
REMINDERS:
•The Engine Star t/Stop but ton needs to be on
•The Gear Shift needs to be in (P) Park
See section 4 in the Owner’s Manual for more information .
For illustrative purposes only . Your actual display, buttons and/or features may vary .(But ton located on driver ’s panel, left of the steering wheel)
Power Liftgate Open/Close Button*
Press and hold the Power Liftgate Open/Close button B to open or close the Liftgate automatically .
B
Manual Folding Mirrors*
To fold the mirrors in manually, pull the mirror towards the window .
Refer to section 4 in the Owner’s Manual for more information .
For illustrative purposes only . Your actual display, buttons and/or features may vary .
If needed, pull the mirror firmly until it folds .
QUICK TIP

DRIVER’S PANEL
DRIVER’S PANEL
REMINDER: When activated or but ton is pressed, the rear passenger windows will not operate from the rear controls .
See section 4 in the Owner’s Manual for more information .
Press C to lock the rear passenger doors . An indicator will illuminate G showing the system is active .
This system is enabled by default, and then activated once the button C is pressed . To deactivate, press the button again .
Electronic Child Safety Lock System
•To use electrical accessories
–ACC position
–When in the OFF position and without depressing the brake pedal, press the ENGINE START/STOP but ton once
–ON position
–When already in the ACC position and without depressing the brake pedal, press the ENGINE START/STOP but ton again
•When in the OFF position and without depressing the brake pedal, press the ENGINE START/STOP but ton t wice
•Keeping the vehicle in the ACC or ON position for extended periods of time without turning the engine on may discharge the vehicle’s bat ter y opening
QUICK TIPS
REMINDERS:
•
If the Smar t Key fob bat ter y is dead, you can still star t the engine by pressing the ENGINE START/STOP but ton with the Lock-but ton end of the Smar t Key . The Smar t Key must contact the ENGINE START/STOP but ton directly, at a right angle
•
In an emergency situation while the vehicle is in motion, you are able to turn the engine off and to the ACC position by pressing the ENGINE START/STOP but ton for more than 2 seconds or 3 times successively within 3 seconds
Engine Start/Stop Button†7
To start the engine:
1 . Depress the brake pedal
2 .
Press the ENGINE START/STOP button while the gear shift is in P (Park) or N (Neutral)
To turn the engine OFF, press the ENGINE START/STOP button while the gear shift is in P (Park) .
To use the ENGINE START/STOP button, you must have the Smart Key on your person or
inside the vehicle .
ENGINE
START
STOP
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Engine Start/Stop Button Video
QR CODE
See section 5 in the Owner’s Manual for more information .
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED31
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electronic Child Safety Lock System Video
QR CODE

AUTO Light – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically depending on the amount of light outside the vehicle .
Daytime Running Lights (DRL) – DRL may help others to see the front of your vehicle during the day . The lights will turn on automatically when the ignition or Engine Start/Stop button is ON and the headlight switch is in the AUTO position, unless one of the following occurs:
• Headlights are on
• Parking brake is applied
• Engine is turned off
• Switch is in the DRL OFF position
Headlight / High Beam Lever Operation
•Rotate lever switch to change the headlight function:
•
Press lever away from you to turn high beam headlights ON
•
Pull lever to flash headlights/high beams or to turn off the high beams
High Beam Assist (HBA)* – High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from other vehicles and road conditions .
To enable HBA , toggle the light switch to the AUTO Light position and turn on the high beams by pushing the lever away from you . The High Beam Assist indicator will illuminate .
*IF EQUIPPED32TELLURIDE FEATURES & FUNCTIONS GUIDE
REMINDERS:
•
High Beam Assist does not operate below cer tain speeds, or in some lighting and driving conditions . Please be aware of your surroundings and exercise proper road etiquet te when operating a vehicle using the high beams
•HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously . If the lever is pulled toward you while HBA is operational, HBA will turn off
•If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
•
When the HBA indicator illuminates on the instrument cluster, the HBA is not working properly . See an authorized Kia dealer for ser vice
OFF
OFF
)FBEMJHIU
QPTJUJPO
1BSLJOH
-JHIU
\
QPTJUJPO
AUTOAuto Light /DRL/ High Beam Assist*
OFFOFF position
Headlights & High Beams
See section 4 in the Owner’s Manual for more information .
A
To operate Turn Signals: Move lever up/down for right/left turn signal .
One-touch lane change signal is activated by briefly pressing the turn signal lever slightly for less than 1 second and then releasing . The lane change signal will blink 3 times .
To change how many times the lane change signal blinks (3/5/7), go to User Settings in the LCD instrument cluster modes .
To operate Fog Lights: Press switch A up/down to turn on/off the Fog Lights .
Turn Signals & Fog Lights*
REMINDER: Headlights must be on for fog light operation .
See section 4 in the Owner’s Manual for more information . For illustrative purposes only . Your actual display, buttons and/or features may vary .
STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS