2022 KIA STINGER steering wheel

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
REMINDER: Cruise Control will not activate until the brake pedal has been depressed at least once after the ignition is ON or engine starting
Your vehicle’s steering wheel buttons may differ from those in the illustrations .
Refer to section 5 in the Owner’s Manual for more information .
CRUISE
RESOKSET
CANCEL
OK
RESOKSET
A Driving Assist button: Press the button to turn the cruise control ON/OFF
B RES+ button: Press up to resume or increase cruising speed
B SET– button: Press down to set or decrease cruising speed
C PAUSE/RESUME button: Press to pause Cruise Control . Press again to resume Cruise Control
Cruise Control (CC)
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED17
A
B
C
•
Cruise Control is designed to function above approximately 20 mph only
•
Cruise Control will not activate until the brake pedal has been depressed at least once after ignition ON or engine star t
QUICK TIPS

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Smart Cruise Control is designed to maintain a predetermined distance from vehicles detected ahead by automatically adjusting the driving speed as needed . When traffic is detected, the vehicle will slow down to maintain a
set distance behind traffic without depressing the accelerator or brake pedal .
With SCC on and activated, the vehicle distance set, and the system detects a vehicle slowing or stopping, the system can bring the vehicle to a complete stop . When the vehicle ahead starts to move forward, SCC re-engages . If the vehicle ahead stops for more than 3 seconds, the accelerator pedal or the RES+ button must be pressed to start moving the vehicle .
Smart Cruise Control will adjust acceleration based on the drive mode selected in the Drive Mode Integrated Control system .
Press the Driving Assist button* on the Steering Wheel A to activate and the speed will be set to the current vehicle speed . SCC may decrease the speed to maintain the distance with the vehicle in front .
To set/adjust the SCC speed:
•Press the Driving Assist button A to turn the system ON . The CRUISE indicator will illuminate on the instrument cluster
•Accelerate/decelerate to the desired speed
•Press the R E S + / S E T– button B to set the speed . Press the R E S + / S E T– button B up/down to increase/decrease the set speed
To set the vehicle distance:
•Press the Vehicle Distance button C on the steering wheel
•
Each time you press C the vehicle distance will change D, indicated by the number of bars that appear on the display E
To pause/resume SCC operation: Depress the brake pedal or press the Pause/Resume button* B . The
cruise indicator on the instrument cluster will change .
To turn SCC OFF: Press the Driving Assist button A . The CRUISE indicator on the instrument cluster will turn OFF .
To adjust the sensitivity of SCC: Press the mode button F on the Steering Wheel . With the OK button H, select Drive Assistance, then SCC Response . Then select Fast, Normal or Slow .
Images are for illustrative purposes only and may not reflect actual feature or operation .
See section 5 in the Owner’s Manual for more information .
CRUISE
CANCEL
RESOKSET
RESOKSETCRUISE60MPH
(Distances are approximate and var y depending on vehicle speed)
(Display on LCD screen)
172ft130ft
82ft
106ft
Smart Cruise Control (SCC)†6
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Smart Cruise Control with Stop & Go Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED18STINGER FEATURES & FUNCTIONS GUIDE
AD
E
F
HB
CF

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Lane Following Assist is designed to help ensure that the vehicle stays centered in its lane A by monitoring the detected lane markings ahead and adjust the steering . When driving, LFA can be switched on and off
by pressing the Driving Assist button B . When turned on, the instrument cluster indicator will initially illuminate white when turned ON . It will remain white when the system does not detect the lane markers . When LFA detects the lane markers and can assist the steering, the LFA icon will illuminate green C .
LFA will operate only when these conditions are met:
•LFA recognizes both sides of the lane markers the vehicle is traveling in
•The vehicle is traveling slower than 120 mph
LFA User Settings:
•
To go to User Settings in the Instrument Cluster, press the Mode button D on the Steering Wheel when the vehicle is at a standstill, gear shift is in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To enable LFA , when in User Settings, press the Move (OK) button E up/down and Select Driver Assistance then Driving Assist, and select Lane Following Assist . Press the OK button E
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings
•
Some vehicles have a Lane Driving Assist / Lane Safety button* on the Driver ’s Panel or the Steering Wheel B . Press to activate Lane Following Assist
Lane Following Assist (LFA)†6
RESOKSET
RESOKSET
Images are for illustrative purposes only and may not reflect actual feature or operation .
LFA is supplemental . Do not solely rely on this system and always pay attention to the road and its conditions .
See section 5 in the Owner’s Manual for more detailed information, limitations and conditions .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Lane Following Assist (LFA) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED20STINGER FEATURES & FUNCTIONS GUIDE
A
C
D
E
B
REMINDER: LFA is not a substitute for safe and proper driving . Always drive safely and use caution .

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
116mi
R5643mi80°F
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) is designed to warn the driver under certain conditions . It may activate the Electronic Stability Control (ESC) and temporarily apply braking if it detects cross traffic
approaching the vehicle when the vehicle is in reverse .
When the RCCA rear-corner radar sensors detect approaching vehicles from the rear left or rear right side of the vehicle A, RCCA will sound a warning, the warning indicators on the outside rearview mirror will illuminate and a message will appear on the Instrument Cluster LCD B and the audio head unit .* If RCCA detects that the collision risk has increased, RCCA automatically applies the brakes to reduce your speed, potentially helping to minimize the effects of a possible collision .
RCCA is designed to operate under the following conditions:
•When the gear shift is in Reverse
•When the vehicle is moving slower than 6 mph
RCCA User Settings:
•To go to the User Settings menu in the Instrument Cluster, press the Mode button C on the Steering Wheel when the vehicle is at a standstill, gear shift in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To turn RCCA on when in User Settings , press the Move (OK) button D up/down, select Driver Assistance, Parking Safety, Rear Cross-Traffic Safety and then press OK D
•
To set the warning timing, go to User Settings , press the Move (OK) button D up/down, then go to Driver Assistance, Warning Timing and press the OK button D
•Select one of the settings:
–
Early/Normal/Standard: Maximizes the amount of distance between the vehicles before the initial warning occurs
– L a t e : Reduces the amount of distance between the vehicles before the initial warning occurs
•The default Warning Timing is set to Normal . If the Warning Timing is changed, the warning time of other Driver Assistance systems may also change
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings
Rear Cross-Traffic Collision-Avoidance Assist (RCCA)†6
RESOKSET
See section 5 in the Owner’s Manual for more information .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED22STINGER FEATURES & FUNCTIONS GUIDE
A
B
C
D
REMINDERS:
•
The RCCA feature can be activated or deactivated in User Set tings, under Driver Assistance, Parking Safet y
•
When vehicle power is cycled, RCCA will remain in the previous state
•
When a vehicle is approaching within the sensing range, and traveling faster than 3 mph, the RCCA system will show a warning
•
RCCA is a supplemental system . Do not solely rely on this system and always pay at tention to the road and its conditions
•RCCA Warning Volume can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings on the audio head unit . Go to Driver Assistance, then Warning Volume
QUICK TIP

Headlight position
Parking light position
AUTO*Auto Light* / LBA position
DRL/OFFOFF or DRL OFF position
Headlight position
Tail Light position
AUTOAuto Light / LBA-D* / High Beam Assist*
OFFOFF position
Headlights & High Beams
AUTO Light – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically depending on the amount of light outside the vehicle .
Low Beam Assist-Dynamic (LBA-D) / Dynamic Bending Light (DBL)* – LBA can help improve visibility during nighttime driving by aiming the low-beam headlights toward the direction the vehicle is moving . LBA controls the aiming direction based on steering angle and speed .
When the light switch is in the AUTO light position, LBA will activate .
High Beam Assist (HBA) – High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from other vehicles and road conditions .
To enable HBA , toggle the light switch to the AUTO Light position and turn on the high beams by pushing the lever away from you . The High Beam Assist indicator will illuminate .
Daytime Running Lights (DRL) – DRL can make it easier for others to see the front of your vehicle during the day . The lights will be on automatically unless one of the following occurs:
•Headlights are on
•Parking brake is applied
•Switch is in the DRL OFF position
•Engine is turned off
Headlight / High Beam Lever Operation
•
Rotate lever switch to change the headlight function:
•
Press lever away from you to turn high beam headlights ON
•
Pull lever to flash headlights/high beams
See section 4 in the Owner’s Manual for more information .
STEERING WHEEL
CONTROLS
STEERING WHEEL CONTROLS
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED29
REMINDERS:
•
High Beam Assist does not operate below cer tain speeds, or in some lighting and driving conditions . Please be aware of your surroundings and exercise proper road etiquet te when operating a vehicle using the high beams .
•
HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously . If the lever is pulled toward you while HBA is operational, HBA will turn off
•
If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
•
DRL only operates during the day time
REMINDER: When the LBA indicator illuminates on the instrument cluster, the LBA is not working properly . See authorized Kia dealer for ser vice .

STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS
One-touch Lane Change Signal
To operate:
•Move lever up/down for right/left turn signal
•Slightly move lever up/down to activate one-touch lane change signal
Turn Signals
For more information on the User Settings Mode, please refer to your Owner’s Manual .
*IF EQUIPPED30STINGER FEATURES & FUNCTIONS GUIDE
REMINDERS:
•
One-touch lane change signal is activated by briefly pressing the turn signal lever slightly for less than 1 second and then releasing . The lane change signal will blink 3 times
•
To change how many times the lane change signal blinks (3/5/7), go to User Set tings in the LCD instrument cluster modes

To operate:
•Move lever up/down to change wiper modes
–MIST: Single wipe
–OFF: Wiper off
–AUTO: Auto Rain Sensing
–LO: Slow wipe
–HI: Fast wipe
•
Pull to spray and wipe
Auto Rain Sensing
The rain sensor located on the upper end of the windshield glass is designed to sense the amount of rainfall and control the wiping cycle for the proper interval . The more it rains, the faster the wiper operates . When the rain stops, the wiper stops .
To turn ON the auto rain sensing wipers, move lever up/down to AUTO .
To adjust the auto rain sensing wiper speed setting, move the speed control switch A up/down .STEERING WHEEL
CONTROLS
STEERING WHEEL CONTROLS
MIST
OFF
AUTO LOHIAUTO
Lifting Wipers (Wiper Service Mode)
To lift the windshield wipers to clean windshield, inspect or replace wiper blades or raise wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the service position C .
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch to the MIST position B and hold the switch for more than two seconds until the wiper blade is in the fully up position .
To return wipers to normal position, turn the ignition ON, then activate MIST .See section 4 in the Owner’s Manual for more information .
Windshield Wipers & Washers
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wipers and Wiper Stalk Video
Wiper Service Mode Video
QR CODES
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED31
•
When the Engine Star t/Stop but ton is in the ON position and the wiper switch is in AUTO mode, the wiper will automatically operate once to per form a self-check of the system
•
Set the wiper to the OFF position when the wiper is not in use
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the Smar t Power Liftgate* lid control, turn off the auto rain sensing wipers and fold in the mirrors
•
Moving lever to HI increases Intermit tent wipe frequency and wipe speed . Moving lever to LO decreases frequency of wipes
•
Pressing but ton A up increases Intermit tent wipe frequency and wipe speed . Pressing but ton down decreases frequency of wipes
QUICK TIPS
A
C
B

STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS
(GT steering wheel illustration shown)
(GT steering wheel illustration shown)
Manual Tilt/Telescoping Steering Wheel*† 26
To adjust the Steering Wheel manually, push the lock-release lever D down and adjust to the desired angle B and distance C .
When finished, pull the lock-release lever D up to lock Steering Wheel in place .
Do not adjust the steering wheel while driving as this may cause you to lose control of the vehicle . See section 4 in the Owner’s Manual for more information .
Do not adjust the steering wheel while driving as this may cause you to lose control of the vehicle . See section 4 in the Owner’s Manual for more information .
Adjust the steering wheel angle B and position C with the switch A on the steering column . Move the steering wheel so it points towards your chest, not toward your face . Make sure
you can see the instrument panel warning lights and gauges .
After adjusting, push the steering wheel both up and down to be certain it is locked in position . Always adjust the position of the steering wheel before driving .
See section 4 in the Owner’s Manual for more information .
Power Tilt/Telescoping Steering Wheel*† 26
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED32STINGER FEATURES & FUNCTIONS GUIDE
C
A
D
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFF
OFF
P
Heated Steering Wheel*
While the Engine Start/Stop button is in the ON position, press E to turn the steering wheel heater ON . The button indicator will illuminate .
The steering wheel heater will turn off automatically in 30 minutes, or when the button is pressed again
to deactivate .E
B
REMINDER: To prevent discharge from the bat ter y, do not adjust when the engine is OFF .
REMINDER: If the steering wheel becomes too warm, turn the system off . The heated steering wheel may cause burns even at low temperatures, especially if used for long periods of time .
•
It may be helpful to pull/push the bot tom of the Steering Wheel towards/away from you to adjust desired distance prior to adjusting the angle
QUICK TIP