2022 KIA STINGER lights

STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS
(GT steering wheel illustration shown)
(GT steering wheel illustration shown)
Manual Tilt/Telescoping Steering Wheel*† 26
To adjust the Steering Wheel manually, push the lock-release lever D down and adjust to the desired angle B and distance C .
When finished, pull the lock-release lever D up to lock Steering Wheel in place .
Do not adjust the steering wheel while driving as this may cause you to lose control of the vehicle . See section 4 in the Owner’s Manual for more information .
Do not adjust the steering wheel while driving as this may cause you to lose control of the vehicle . See section 4 in the Owner’s Manual for more information .
Adjust the steering wheel angle B and position C with the switch A on the steering column . Move the steering wheel so it points towards your chest, not toward your face . Make sure
you can see the instrument panel warning lights and gauges .
After adjusting, push the steering wheel both up and down to be certain it is locked in position . Always adjust the position of the steering wheel before driving .
See section 4 in the Owner’s Manual for more information .
Power Tilt/Telescoping Steering Wheel*† 26
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED32STINGER FEATURES & FUNCTIONS GUIDE
C
A
D
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFF
OFF
P
Heated Steering Wheel*
While the Engine Start/Stop button is in the ON position, press E to turn the steering wheel heater ON . The button indicator will illuminate .
The steering wheel heater will turn off automatically in 30 minutes, or when the button is pressed again
to deactivate .E
B
REMINDER: To prevent discharge from the bat ter y, do not adjust when the engine is OFF .
REMINDER: If the steering wheel becomes too warm, turn the system off . The heated steering wheel may cause burns even at low temperatures, especially if used for long periods of time .
•
It may be helpful to pull/push the bot tom of the Steering Wheel towards/away from you to adjust desired distance prior to adjusting the angle
QUICK TIP

OTHER KEY

FEATURES
OTHER KEY FEATURES
How to Sync Transmitter with HomeLink®
If programming for the first time, begin with Step 1 (repeating this step will delete all information) .
To program non-rolling and rolling code garage door openers and other devices:
1 . Press and hold the left A and center C buttons simultaneously until the indicator light G begins to flash (to reprogram buttons, skip this step)
2 . Press and hold the desired button A B C and hold the button on the transmitter while it is approximately 1 to 3 inches away from the mirror . The HomeLink® Indicator light F will flash rapidly once the frequency signal has been successfully programmed
To finish programming rolling code garage door openers, complete these steps:
3 . Locate the “learn” or “smart ” button on the garage door ’s motor head unit . Press and release the button and complete Step 4 within 30 seconds
4 . Firmly press and release the programmed HomeLink® button up to three times
Operating HomeLink®:
Press one of the programmed HomeLink® buttons .
Erasing programmed buttons:
Press and hold the A and C buttons simultaneously for approximately 20 seconds, and then release both buttons within 30 seconds .
The HomeLink® / Auto-Dimming Rearview Mirror* is designed to reduce glare from a vehicle’s headlights located in the rear and also connect up to three electronic transmitters into one location .
HomeLink® with Auto-Dimming Rearview Mirror*† 14
A HomeLink® Channel 1
B HomeLink® Channel 2
C HomeLink® Channel 3
D Garage Door Opener Status Indicator: Closing or Closed
E HomeLink® Operation Indicator
F Garage Door Opener Status Indicator: Opening or Open
G HomeLink® User Interface Indicator
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
HomeLink® Support
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED50STINGER FEATURES & FUNCTIONS GUIDE
•
You can reprogram a single HomeLink but ton by repeating Step 2
•Erasing the programmed but tons will delete all trained transmit ters
QUICK TIPS
ABC
D
EF
G

Smart Power Liftgate*† 18 (Continued)
HOLD
See section 4 in the Owner’s Manual for more information .
Opening with no-touch activation:
When the Smart Key fob is on your person and you are within close proximity
of the back of the vehicle, the hazard lights will blink and a chime will sound for about 3 seconds as an alert that the Smart Power Liftgate is about to open .
Then the alert system will blink and chime two additional times before opening the Smart Power Liftgate .
The Smart Power Liftgate feature is OFF by default . To enable the Smart Power Liftgate, go to User Settings in the LCD Instrument Cluster modes .
Smart Key:
Using the Smart Key fob to automatically to open the Smart Power Liftgate*, press and hold the Smart Key Liftgate button A . Press again and hold to close .
OTHER KEY FEATURES
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Kia Smart & Folding Key Fobs Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED53
OTHER KEY

FEATURES
A
•
The Liftgate must be unlocked before it can be opened by the Liftgate Release but ton
•
The Liftgate unlocks automatically and then can be opened manually when the Smar t Key is within close proximit y to the back of the vehicle
QUICK TIPS
REMINDERS:
•
Smar t Power Liftgate may be damaged if at tempting to open or close manually
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the Smar t Power Liftgate lid control using the but ton inside the glove compar tment, turn off the auto rain-sensing wipers and fold in the mirrors
•
When not in use, keep the Liftgate Lid Control but ton in the OFF position
•
Ensure all obstacles are out of the way of the Liftgate lid when operating the Smar t Power Liftgate

Automatic Turn Off Function
The interior lights automatically turn off approximately 20 seconds after the Engine Start/Stop button is
turned OFF .
Map/Room Lamp Operation
Map Lamps – These lights produce spot beams for convenient use as map lamps or as personal lamps for the driver or the front passenger . Press the buttons A to turn the map lamps ON/OFF .
Room button – Press the button B to turn the front and rear lamps ON/OFF .
Door button – When the Door button C is pressed the front and rear lamps will turn ON as follows:
•When a door is opened or doors are unlocked with the Smar t Key, the lamps will turn ON for approximately 30 seconds
•If the Engine Start/Stop button is in the ACC/OFF position and a door is open, the lamps will stay ON for approximately 20 minutes
•If the Engine Start/Stop button is in the ACC/ON position and a door is open, the lamps will stay ON
The lamps will turn OFF immediately if the Engine Start/Stop button is turned ON or all doors are locked .
OTHER KEY FEATURES
Map/Room Lamps
See section 4 in the Owner’s Manual for more information .
*IF EQUIPPED54STINGER FEATURES & FUNCTIONS GUIDE
ABC
A
OTHER KEY

FEATURES
•
When doors are unlocked by the Smar t Key, the lamp turns ON for approximately 30 seconds
•
If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 3 seconds after the system is in armed stage
•
Using interior lights for an extended period of time may cause bat ter y discharge
QUICK TIPS
REMINDER: When room lamp lens is pressed ON it will remain ON, even when the map lamp switch is in the OFF position .
(Overhead lamp console)