51†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
SEATING
SEATING
3rd-Row Folding Seat*†1 2
One-Touch Slide & Fold 2nd Row Seats*†1 2
Folding 3rd-Row Seat
1 . Fully lower the headrest A
2 . Pull the Seat folding strap B located on the Seatback
3 . Fold the Seat down
To get in and out of the 3rd Row Seat, adjust the 2nd Row Seat by pressing the One-Touch Slide & Fold 2nd Row Seats (located on top C and side D of the 2nd-row seatback):
1 . Set the front seatback to the most upright position, and slide the seat forward, if needed
2 . Lower the 2nd Row Seat Headrest to the lowest position
3 . Insert the seatbelt buckle into the pocket between the
rear seatback and the cushion
4 . Press the One-Touch Slide & Fold buttons to slide the Seat forward
Refer to section 3 in the Owner ’s Manual for more information .
Images are for illustrative purposes only and may not reflect actual feature or operation .
Refer to section 3 in the Owner ’s Manual for more information .
Images are for illustrative purposes only and may not reflect actual feature or operation .
REMINDER: Do not use the One-Touch Slide & Fold but tons while the 2nd-row passenger seat is occupied .
B
CD
AA
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
2nd & 3rd Row Folding Seats Video
One-Touch Slide & Fold 2nd-Row Seats Video
QR CODE
The strap can be used in the back of the 2nd Row Seat to slide and fold the 2nd Row Seats .
QUICK TIP
57†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1 (repeating this step will delete all information) .
To program non-rolling and rolling code garage door openers and other devices:
1 . Press and hold the A and C buttons simultaneously until the indicator light G begins to flash (to reprogram buttons, skip this step)
2 . Press and hold the desired button A B C and hold the button on the transmitter while it is approximately 1 to 3 inches away from the mirror . The HomeLink® Indicator light E will flash rapidly once the frequency signal has been successfully programmed
To finish programming rolling code garage door openers, complete these steps:
3 . Locate the “learn” or “smart ” button on the garage door ’s motor head unit . Press and release the button and complete Step 4 within 30 seconds
4 . Firmly press and release the programmed HomeLink® button up to three times
Operating HomeLink®:
Press one of the programmed HomeLink® buttons .
Erasing programmed buttons:
Press and hold the A and C buttons simultaneously for approximately 20 seconds, and then release both buttons within 30 seconds .
The HomeLink® / Auto-Dimming Rearview Mirror* is designed to reduce glare from a vehicle’s headlights located in the rear and also connect up to three electronic transmitters into one location .
HomeLink®†3 with Auto-Dimming Rearview Mirror*
A HomeLink® Channel 1
B HomeLink® Channel 2
C HomeLink® Channel 3
D Garage Door Opener Status Indicator: Closing or Closed
E HomeLink® Operation Indicator
F Garage Door Opener Status Indicator: Opening or Open
G HomeLink® User Interface Indicator
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit . For more information, go to w w w .HomeLink .com or call (800) 355-3515 .
Images are for illustrative purposes only and may not reflect actual feature or operation .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Homelink® Support Video
QR CODE
•You can reprogram a single HomeLink® but ton by repeating Step 2
•Erasing the programmed but tons will delete all trained transmit ters
QUICK TIPS
OTHER KEY FEATURES
OTHER KEY FEATURES
BC
D
EG
F
A
