2022 KIA NIRO PHEV warning lights
[x] Cancel search: warning lightsPage 24 of 66
The BCW system uses radar sensors to help alert the driver in certain situations, such as if it detects an approaching vehicle in the driver ’s blind spot before changing lanes The light on the BCW button A will illuminate when turned ON The outside rearview mirror warning lights will also illuminate for 3 seconds
The system will become active when the vehicle is traveling more than approximately 20 mph and will alert the driver if another vehicle is detected by the radar sensor
1st-stage alert: When another vehicle is detected within the BCW system boundary B, or when a vehicle is detected within the boundary C approaches at a high speed, a yellow
indicator will illuminate on the outside rearview mirrors
2nd-stage alert: When 1st-stage alert is on and the driver activates a turn signal, a flashing yellow indicator will illuminate on the outside rearview mirrors and the system will sound an alert
REMINDERS:
•
The BCW Warning Volume can be adjusted in the Vehicle Set tings on the audio head unit Adjusting this volume set ting may also change other Driver Assistance systems’ volume set ting
•
If the BCW is turned OFF and the ignition is cycled, the BCW system returns to ON
AUTOOFF # V U U P O M P D B U F E M F G U P G U I F 4 U F F S J O H 8 I F F M
% S J W F S " U U F O U J P O 8 B S O J O H J T O P U B T V C T U J U V U F G P S T B G F E S J W J O H B O E N B Z O P U E F U F D U B M M J O T U B O D F T P G J O B U U F O U J W F E S J W J O H Q S B D U J D F T ' B J M V S F U P Q B Z B U U F O U J P O U P U S B W F M D P O E J U J P O T B O E W F I J D M F P Q F S B U J P O D P V M E S F T V M U J O M P T T P G W F I J D M F D P O U S P M " M X B Z T E S J W F T B G F M Z B O E V T F D B V U J P O
# $ 8 J T B T V Q Q M F N F O U B M T Z T U F N % P O P U S F M Z T P M F M Z P O U I J T T Z T U F N
B O E B M X B Z T E S J W F T B G F M Z 3 F G F S U P T F D U J P O T J O U I F 0 X O F S s T . B O V B M G P S N P S F J O G P S N B U J P O
% " 8 N P O J U P S T U I F E S J W J O H T U Z M F P G U I F E S J W F S B O E
J O D F S U B J O T J U V B U J P O T
D B O H J W F B X B S O J O H T J H O B M G P S U I F E S J W F S U P U B L F B C S F B L G S P N E S J W J O H
% " 8 J T T F U U P 0 / C Z E F G B V M U 5 P U V S O % " 8 0 ' '
U V S O U I F J H O J U J P O P O B O E U I F O T F M F D U 6 T F S 4 F U U J O H T J O U I F - $ % % J T Q M B Z P O U I F * O T U S V N F O U $ M V T U F S 5 I F O H P U P % S J W J O H " T T J T U B O E T F M F D U % S J W F S " U U F O U J P O 8 B S O J O H 4 F U % " 8 U P / P S N B M P S ) J H I 4 F O T J U J W J U Z
Driver Attention Warning (DAW) modes:
Off: The DAW is deactivated D
Normal: The DAW alerts the driver of his/her fatigue level or inattentive driving practices
High Sensitivity: The DAW alerts the driver of his/her fatigue level or inattentive driving practices faster than Normal mode
If the DAW is activated, the DAW information will appear on the Instrument Cluster LCD E when you select the Driving Assist / Assist mode A message, “Consider taking a break,” appears on the LCD display and a warning sounds to suggest that the driver take a break when the driver ’s attention level is below one bar F
22†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDNIRO HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Blind-Spot Collision Warning (BCW) Video
Driver Attention Warning (DAW) Video
QR CODEBlind-Spot Collision Warning (BCW)*†4Driver Attention Warning (DAW)*†5
REMINDERS:
•
The setup of DAW will be maintained, as selected, when the ignition is cycled
•
When activated, DAW does not display “Consider taking a break ” message when the total trip driving time is less than 10 minutes
•
DAW will enter a standby mode if the camera does not detect the lanes and/or the driving speed remains under 40 mph
Driver Attention Warning
System Off
L ast Break ——:—— Attention Level
LOW
HIGHLast Break 05:27
Attention Level
LOWHIGHLast Break 05:27
Consider taking a break
Driver Attention Warning
System Off
L ast Break ——:—— Attention Level
LOW
HIGHLast Break 05:27
Attention Level
LOWHIGHLast Break 05:27
Consider taking a breakIllustrations are for demonstration purposes only Actual images or but tons on vehicle may var y
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
BA
C
DEF
Page 35 of 66
33*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
Refer to section 4 in the Owner ’s Manual for more information
Headlight position
Parking light position
AUTO*Auto Light Position / DRL / HBA*
OFFOFF position
To operate:
•Rotate lever to change the Headlight function
•Push lever to turn High Beams ON
•Pull lever to flash Headlights/High Beams
High Beam Assist (HBA)* – The High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from oncoming vehicles and road conditions
When switch is in the AUTO position and the vehicle’s ignition or the Engine Start/Stop button* is on, the High Beam Assist will operate To turn HBA off, change the switch setting
AUTO Light position – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically depending on the amount of light outside the vehicle
Daytime Running Lights (DRL) – DRL may help others to see the front of your vehicle during the day The lights will be on automatically when the ignition or Engine Start/Stop button* is ON and the headlight switch is in the AUTO position, unless one of the following occurs:
•Headlights are on
•Parking brake is applied
•Fog lights are on
•Engine is turned off
Turn Signals & Fog Lights*
To operate:
•Tu r n Signals - Move lever Up/Down for Right/
Left Turn Signal
•Fog Lights - Press switch A to turn Fog Lights ON/OFF
One-Touch Lane Change Signal is activated by briefly pressing the Turn Signal Lever slightly for less than 1 second and then releasing The lane change signal will blink 3 times
To change how many times (3/5/7) the Lane Change Signal blinks, go to User Settings Mode in the LCD Instrument Cluster modes REMINDERS:
•
High Beam Assist does not operate below cer tain speeds, or in some lighting and driving conditions Please be aware of your surroundings and exercise proper road etiquet te when operating a vehicle while using the high beams
•HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously If the lever is pulled toward you while HBA is operational, HBA will turn off
•If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
•DRL only operates during the day time
•
The DRL system turns off when the headlights are ON, parking brake is applied or the front fog lights are turned on
REMINDER: Headlights must be ON for Fog Light operation
Headlights & High Beams
STEERING WHEEL CONTROLS
STEERING
WHEEL CONTROLSA