2022 KIA CARNIVAL light

†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPED12CARNIVAL FEATURES & FUNCTIONS GUIDE
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
L ANE KEEPING ASSISTL ANE KEEPING ASSISTL ANE KEEPING ASSIST
(Located on Driver ’s Panel to the left of the steering wheel)
Lane Keeping Assist is not a substitute for safe driving and may not always warn the driver if the vehicle is driven outside of its lane. Always drive safely and use caution.
For illustrative purposes only. Your actual display, but tons and/or features may var y.
Actual User Set tings steps may var y by model. Refer to section 5 in the Owner ’s Manual for more information.
Lane Keeping Assist (LKA)†6
Lane Keeping Assist is designed to detect the lane markers on the road with a front view camera on the windshield, and may assist the driver ’s steering to help keep the vehicle in the lane. When turned on, the instrument cluster indicator will initially illuminate white. It will remain white when the vehicle is traveling slower than 40 mph or when the system does not detect the lane markers. When the system detects the lane markers and can assist the steering, the LK A icon will illuminate green.
If LK A detects that you are moving outside of your lane, the system may give an audible warning and display Lane Departure Warning on the instrument cluster. If the vehicle continues to move outside of the lane, LK A may provide steering, trying to prevent the vehicle from moving outside its lane.
LK A is the operating mode by default when the Lane Safety button* A is depressed to ON (press and hold to turn LK A on/off).
There are three available modes:
•Assist: LK A will automatically assist the driver ’s steering when lane departure is detected to help prevent the vehicle from moving out of its lane
•Warning Only: LK A will warn the driver with an audible warning when lane departure is detected. The driver must steer the vehicle
•Off: LK A will turn off. The B indicator light will turn off on the cluster
All systems will operate under the following conditions:
•The vehicle speed exceeds approximately 40 mph
•
LK A recognizes both sides of the lane markers the vehicle is traveling in
•
The vehicle is between the lane markers
When the front-view camera does not detect the lane traveling in, the lanes are not illuminated gray
When the front-view camera detects the lane traveling in, both lanes are illuminated gray
L ANE KEEPING ASSIST
When the front-view camera detects the vehicle moving outside of the lane it is traveling in, a vehicle crossing lane indicator will blink, either on the left or right lane (as shown in both images above)
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Lane Keeping Assist (LK A) Video
QR CODE
A
B

ADAS
†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
19
Images are for illustrative purposes only and may not reflect actual feature or operation.
60mph
Highway Driving Assist (HDA)*†6 a
Highway Driving Assist is designed to adjust the speed of the vehicle when driving on limited/controlled access highways.
To enable HDA on some models, go to User Settings in the Instrument Cluster or, on other models, go to the Vehicle Settings* in the audio head unit. Go to Setup > Vehicle > Driver Assistance > Driving Convenience > Highway Driving Assist.
To activate HDA , press the Driving Assist button A on the Steering Wheel controls.
HDA will operate only when these conditions are met:
•SCC and LFA are operating
•The vehicle is traveling slower than 110 mph
•
When driving on limited access highways, such as Interstate, Federal and State freeways
When HDA is activated and the conditions are met, the Instrument Cluster indicator light B will illuminate green. If the conditions are not met, HDA will be in standby mode and the indicator light B will illuminate white.
When in operation, and if both lanes are recognized, a display C will show the lanes illuminated white and the steering wheel indicator illuminated green.
REMINDER: Current highway speeds and controlled or limited access roads information may var y. Future navigation updates may change this information. See Owner ’s Manual for more information.
Highway Driving Assist is not a substitute for safe driving, may not detect all objects around the vehicle, and only functions on cer tain federal highways. Always drive safely and use caution.
See section 5 in the Owner ’s Manual for more detailed information, limitations and conditions.
MODE
MODE
MODE
MODE
MODE
MODE MODE
MODE
MODE
OKOK
OK
OK
OK
OK
OK
OK
Drive mode (Return button)Cruise Control
Bluetooth Eco L FA
User Settings
HDA
Audio LV DA MSLA - ISLA
MODE
Smart Cruise Control
OK
ROA
MODE
HDA
OK
OK
(Type B Steering Wheel controls)
A
B
C
D
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Highway Driving Assist (HDA) Video
QR CODE

*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 21
Electronic Stability Control (ESC)†8
The ESC system is designed to help stabilize the vehicle during certain cornering maneuvers. It is a good idea to keep the ESC turned on for daily driving whenever possible.
Press the ESC OFF button B to turn Traction Control OFF/ON. Press again to turn on.
To turn OFF both the Traction Control and Stability Control, press and hold for more than 3 seconds. Press again to turn ON.

Hill-Start Assist Control (HAC)†8
HAC helps prevent the vehicle from rolling backwards when accelerating from a stop while on a steep incline. HAC automatically activates whether the ESC is OFF or ON but does NOT activate when the ESC has malfunctioned.
HOLD
HOLDPOWER
DOOR OFFHOLD
#VU UPO
QBOFM
MPDBUFE
MFGU
PG
4UFFSJOH
8IFFM

Instrument Cluster Control
With parking lights/headlights ON, press button A (+) or (-) to adjust the brightness of the instrument panel illumination.
REMINDER: The Instrument Cluster Control does not adjust brightness on the audio head unit screens. Use the display set tings in the Setup menu to adjust the brightness on the screen.
HOLD
HOLDPOWER
DOOR OFFHOLD
DRIVER’SPANEL
DRIVER’S PANEL
AB
•HAC provides a t wo second delay before the vehicle may star t rolling backwards
•When HAC is active (e.g., during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator — this is normal HAC operation
QUICK TIPS
REMINDERS:
•
HAC does not operate when the gear shift is in the P (Park) or the N (Neutral) position
•
HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
Refer to section 5 in the Owner ’s Manual for more information.

†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 23
LRLRLRLR
(But ton/switch panel located on Driver's Door )
(But ton located above center console)
ENGINESTART
STOP
Reverse Parking Aid Function*
The left or right mirror buttons A need to be depressed for the Reverse Parking Aid Function to operate.
When the gear shift lever is moved into R (Reverse) and while the vehicle is moving backwards, the outside rearview mirrors B will rotate downward to aid in reverse parking.
To turn OFF the function, press the L or R buttons again.
The outside rearview mirrors will automatically return to their original positions when:
•The Engine Start/Stop Button is in the OFF position
•The gear shift lever is moved to any position except R (Reverse)
•
Outside rearview mirror switches are not depressed
Engine Start/Stop Button†9
To start the engine:
•Press the brake pedal
•
Press the ENGINE START/STOP button
while the gear shift is in P (Park)
To turn the engine OFF:
•Press the ENGINE START/STOP button
To use the ENGINE START/STOP button, you must have the Smart Key fob inside the vehicle.
REMINDER: When the outside rear view mirror but tons (L or R) A are not depressed, the Reverse Parking Aid Function will not operate and the outside rear view mirrors will not rotate downward
Refer to section 4 in the Owner ’s Manual for more information.
To use electrical accessories:
ACC position
•When in the OFF position and without depressing the brake pedal, press the ENGINE START/STOP but ton once (amber light)
ON position
•When already in the ACC position (orange light) and without depressing the brake pedal, press the ENGINE START/STOP but ton again (reddish orange light)

When in the OFF position and without depressing the brake pedal, press the ENGINE START/STOP but ton t wice (reddish orange light)
Keeping the vehicle in ACC or the ON position for extended periods of time without turning the engine on may discharge the vehicle’s battery
QUICK TIPS
REMINDERS:
•
In an emergency situation while the vehicle is in motion, you are able to turn the engine off and to the ACC position by pressing the ENGINE START/STOP but ton for more than 2 seconds or 3 times successively within 3 seconds
•
If Smar t Key fob bat ter y is dead, with the lock but ton facing the ENGINE START/STOP but ton, hold the fob up against the ENGINE START/STOP but ton and press to star t the engine while pressing the brake pedal
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Engine Start/Stop Button Video
QR CODE
Refer to section 4 in the Owner ’s Manual for more information.
AB
DRIVER’SPANEL
DRIVER’S PANEL

*IF EQUIPPED24CARNIVAL FEATURES & FUNCTIONS GUIDE
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
HOLD
HOLDPOWER
DOOR OFFHOLD
OFFOFF
AUTO
OFFOFF
AUTO
Headlight position
Parking light position
AUTOAuto Light / HBA / DRL
OFFOFF position
Tilt/Telescoping Steering Wheel†2 5
To adjust the Steering Wheel, press the Lock-Release Lever A down and adjust B to the desired angle and C distance.
When finished, pull the Lock-Release Lever A up to lock the Steering Wheel in place.
Headlights & High Beams
To operate:
•Rotate the switch to change the Headlight function
•Push the lever to turn High Beams ON
•Pull the lever to flash Headlights / High Beams
AUTO Light function – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically depending on the amount of light outside the vehicle.
Daytime Running Lights (DRL) - DRL may help others to see the front of your vehicle during
the day. The lights will turn on automatically when the ignition or Engine Start/Stop button is ON and the headlight switch is in the AUTO position, unless one of the following occurs:
•Headlights are on
•Parking brake is applied
•Engine is turned off
•Headlight switch is in the OFF position
High Beam Assist (HBA) - The High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from oncoming vehicles and road conditions.
To enable HBA , toggle the light switch to the AUTO Light position and turn on the high beams by pushing the lever away from you. The High Beam Assist indicator will illuminate.
REMINDERS:
•HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously. If the lever is pulled toward you while HBA is operational, HBA will turn off
•
If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuouslyRefer to section 4 in the Owner ’s Manual for more information.Refer to section 4 in the Owner ’s Manual for more information.
A
B
C
It may be helpful to pull/push the bot tom of the Steering Wheel towards/away from you to adjust the desired distance prior to adjusting the angle.
QUICK TIP

†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 25
MIST: Single wipe
OFF: Wiper off
I N T: Intermittent wipe
LO: Slow wipe
HI: Fast wipe
MISTOFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
HI: Fast wipe
LO: Slow wipe
OFF: Wiper off
OFFOFF
AUTO
OFFOFF
AUTO
*MMVTUSBUJPOT
BSF
GPS
EFNPOTUSBUJPO
QVSQPTFT
POMZ
"DUVBM
GFBUVSFT
PO
WFIJDMF
NBZ
WBS Z
3FGFS
UP
TFDUJPO

JO
UIF
0XOFS sT
.BOVBM
GPS
NPSF
JOGPSNBUJPO5IFTF
JMMVTUSBUJPOT
BSF
GPS
EFNPOTUSBUJPO
QVSQPTFT
POMZ
"DUVBM
GFBUVSF
PO
WFIJDMF
NBZ
WBS Z
3FGFS
UP
TFDUJPO

JO
UIF
0XOFS sT
.BOVBM
GPS
NPSF
JOGPSNBUJPO
Windshield Wipers & Washers
To operate:
•Move lever Up/Down to change wiper modes
•Press button B Up/Down to adjust Intermittent Wipe Speed
•Pull lever to spray and wipe
Rear Wiper & Washer
To operate:
•Rotate Rear Wiper switch to change Wiper modes
•Push to spray and wipe
Turn Signals & Fog Lights*
To operate:
•Turn Signals - Move lever Up/Down for Right/Left Turn Signal
•Fog Lights - Press switch A up/down to turn Fog Lights ON/OFF
REMINDER: Headlights must be ON for Fog Light operation.
The One-Touch Lane Change Signal is activated by briefly pressing the Turn Signal Lever slightly for less than 1 second and then releasing. The lane change signal will blink 3 times.
To change how many times (3/5/7) the Lane Change Signal blinks, go to the User Settings Mode in the LCD Instrument Cluster modes.
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
Refer to section 4 in the Owner ’s Manual for more information.
•Pressing but ton B up increases Intermit tent wipe frequency and wipe speed. Pressing the but ton down decreases the frequency of wipes
•Set the wiper to the OFF position when the wiper is not in use
QUICK TIPS
LO and HI sets the wiper speed. There is no intermit tent wipe function on the Rear Wipers
QUICK TIP
B
A
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Wipers and Wiper Stalk Video
Wiper Service ModeVideo
QR CODE
Headlight position
Parking light position
AUTOAuto Light / HBA / DRL
OFFOFF position

USB
USBC
*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 35
USB Charger Ports, Multimedia USB Port, Power Outlets,
& AC Inverter
USB Charger Ports* B are located in the center panel and in the back of the seats D and center console.
Multimedia USB Port C: Use the Aux port to connect audio devices and the Multimedia USB port to connect USB audio devices and smartphones.
AC Inverter*: 115V/100 watt power inverters are located in the back of the center console and in the luggage zone* (See page 8 for ON/OFF button information).
REMINDERS:
•
Using the power outlets (accessor y plugs) and AC Inver ter for prolonged periods of time with the ENGINE START/STOP but ton in the ACC position (Engine OFF) may cause the bat ter y to discharge
•
Use only the charging cables that your device manufacturer supplied. Third par t y cables may cause damage to your device
•
The USB data por t (Multimedia USB por t) is located next to the Power Outlets. The USB Charger por ts do not suppor t data transfer
Refer to section 4 in the Owner ’s Manual for more information.
Digital Clock*
Audio Head Unit:
Press the SETUP key A then press GENER AL, then DATE/TIME button to display the Time and Date setting screen. Then use the onscreen buttons to adjust time and date.
(Located in the center console in front of gear shift)
For more information, refer to the Car Infotainment System Quick Reference Guide.
USB
POWERPUSHVOL
MAPENGINESTARTSTOPN AV RADIO MEDIASETUP
SEEK
TRACK
ENTER
TUNE
FILE
•
Press the RETURN but ton on the navigation screen to ensure changes are saved
•When needed, Daylight Savings must be enabled in the Set tings screen
•
To access manual date and time set ting, turn GPS time OFF in the Clock Set tings (UVO eSer vices with Premium Navigation System*)
QUICK TIPS
The power outlets are inactive when the Engine Star t/Stop* but ton is OFF.
QUICK TIP
A
BB
D
CENTER PANEL
CENTER PANEL

*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 39
Wireless Smartphone Charging System*
1. Enable Wireless Smartphone Charging System in the User Settings Mode on the Instrument Cluster ’s LCD
2. Place a compatible smartphone on the center of the charging pad A
3. The indicator light B may change to amber once the wireless charging begins
4. Once charging is complete, the amber light may change to green
USB
USB
Requires QI-enabled device or QI-enabled case
Refer to section 4 in the Owner ’s Manual for more information.
CENTER PANEL
CENTER PANEL
B
A
•The smar tphone must be a compatible phone with QI function available
•Wireless charging must be enabled in user set tings
•
If wireless charging does not work, move the smar tphone around the pad until the charging indicator turns amber. Avoid placing other metal items in the bin while charging as to not impede the charging area
•
For wireless charging to occur, all doors (excluding rear hatch) must be closed & the Smar t Key Fob must be detected inside the vehicle
QUICK TIPS
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Wireless Charging Video
QR CODE
REMINDERS:
•
Avoid placing other metal items in the bin while charging as to not impede the charging area
•
This vehicle is equipped with wireless charging technology which allows for a device to be charged using inductive charging; however, device compatibilit y varies. See your Owner ’s Manual for more detailed information and the back page for legal disclaimers
•
Inductive charging systems are less ef ficient than conventional charging through cable. As a result, higher device operating temperatures may be experienced during use
•
Charging Per formance – Device position on the wireless charging system can affect charging per formance. Other factors that may affect the charging rate includes foreign objects, such as coins or pens, and phone case thickness
•If the driver door is opened, charging will be disabled