2022 HYUNDAI VENUE lock

08
8-23
WIPER BLADES
Blade Inspection
Contamination of either the windshield
or the wiper blades with foreign matter
can reduce the effectiveness of the
windshield wiper functionality. Common
sources of contamination are insects,
tree sap, and hot wax treatments used
by some commercial car washes. If the
blades are not wiping properly, clean
both the window and the blades with a
clean cloth dampened with washer fluid.
NOTICE
To prevent damage to the wiper blades,
arms or other components, do not:

[Use gasoline, kerosene, paint
thinner, or other solvents on or near
them.

[Attempt to move the wipers
manually.

[Use non-specified wiper blades.
Information
Commercial hot waxes applied by
automatic car washes have been known to
make the windshield difficult to clean.
Blade Replacement
When the wipers no longer clean
adequately, the blades may be worn or
cracked, and require replacement.
NOTICE
To prevent damage to the wiper arms
or other components, do not attempt to
move the wipers manually.
NOTICE
The use of a non-specified wiper blade
could result in wiper malfunction and
failure.
NOTICE

[In order to prevent damage to the
hood and the wiper arms, the wiper
arms should only be lifted when in
the top wiping position.

[Always return the wiper arms to the
windshield before driving.
Front windshield wiper blade
replacement
OGSR076067
1. Put the front windshield wipers into
the service position.
2. Raise the wiper arm and slightly rotate
the wiper blade assembly to expose
the plastic locking clip.

Maintenance
8-26
For Best Battery Service
OQX089042

[Keep the battery securely mounted.

[Keep the battery top clean and dry.

[Keep the terminals and connections
clean, tight, and coated with
petroleum jelly or terminal grease.

[Rinse any spilled acid from the battery
immediately with a solution of water
and baking soda.
Battery Recharging
WARNING
Always follow these instructions when
recharging your vehicle’s battery to
avoid the risk of SERIOUS INJURY or
DEATH from explosions or acid burns:

[Before performing maintenance or
recharging the battery, turn off all
accessories and place the ignition
switch to the LOCK/OFF position.

[Keep all flames, sparks, or smoking
materials away from the battery.

[Always work outdoors or in an area
with plenty of ventilation.

[Wear eye protection when checking
the battery during charging.

[The battery must be removed from
the vehicle and placed in a well
ventilated area.

[Watch the battery during charging,
and stop or reduce the charging
rate if the battery cells begin boiling
violently.
[The negative battery cable must
be removed first and installed last
when the battery is disconnected.
Disconnect the battery charger in the
following order:
1. Turn off the battery charger main
switch.
2. Unhook the negative clamp from
the negative battery terminal.
3. Unhook the positive clamp from
the positive battery terminal.

[Always use a genuine HYUNDAI
approved battery when you replace
the battery.
By jump starting
After a jump start from a good battery,
drive the vehicle for 20-30 minutes
before it is shutoff. The vehicle may
not restart if you shut it off before the
battery had a chance to adequately
recharge. See “Jump Starting” in chapter
7 for more information on jump starting
procedures.
Information
An inappropriately disposed
battery can be harmful to
the environment and human
health. Dispose of the battery
according to your local law(s) or
regulations.
Reset Features
The following items may need to be reset
after the battery has been discharged or
the battery has been disconnected. See
chapter 3 or 4 for:

[Power Windows

[Trip Computer

[Climate Control System

[Clock

[Audio System

[Sunroof

08
8-27
WARNING
Tire failure may cause loss of
vehicle control resulting in an
accident. To reduce risk of SERIOUS
INJURY or DEATH, take the
following precautions:

[Inspect your tires monthly for
proper inflation as well as wear
and damage.

[The recommended cold tire
pressure for your vehicle can be
found in this manual and on the
tire label located on the driver’s
side center pillar. Always use a
tire pressure gauge to measure
tire pressure. Tires with too
much or too little pressure wear
unevenly causing poor handling.

[Check the pressure of the
spare every time you check the
pressure of the other tires on
your vehicle.

[Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, or traction.

[ALWAYS replace tires with
the same type, size, brand,
construction and tread pattern
as each tire that was originally
supplied with this vehicle. Using
tires and wheels other than the
recommended sizes could cause
unusual handling characteristics,
poor vehicle control, or
negatively affect your vehicle’s
Anti-Lock Brake System (ABS)
resulting in a serious accident.
Tire Care
For proper maintenance, safety, and
maximum fuel economy, you must
always maintain recommended
tire inflation pressures and stay
within the load limits and weight
distribution recommended for your
vehicle.
OQX089049N
All specifications (sizes and
pressures) can be found on a label
attached to the driver’s side center
pillar.
Recommended Cold Tire
Inflation Pressures
All tire pressures (including the
spare) should be checked when the
tires are cold. “Cold tires” means the
vehicle has not been driven for at
least three hours or has been driven
for less than one mile (1.6 km).
Warm tires normally exceed
recommended cold tire pressures
by 4 to 6 psi (28 to 41 kPa). Do not
release air from warm tires to adjust
the pressure or the tires will be
under-inflated. For recommended
inflation pressure, refer to “Tire and
Wheels” in chapter 2.
TIRES AND WHEELS

Maintenance
8-30
Tire Replacement
Tread wear indicatorTread wear indicator
OLMB073027
If the tire is worn evenly, a tread wear
indicator will appear as a solid band
across the tread. This shows there is
less than 2/32 inch (1.6 mm) of tread
left on the tire. Replace the tire when
this happens.
Do not wait for the tread surface to
become level with the tread wear
indicators before replacing the tire.
WARNING
To reduce the risk of DEATH or
SERIOUS INJURY:

[Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, and traction.

[Always replace tires with the
same size as each tire that was
originally supplied with this
vehicle. Using tires and wheels
other than the recommended
sizes could cause unusual
handling characteristics, poor
vehicle control, or negatively
affect your vehicle’s Anti-Lock
Brake System (ABS) resulting in a
serious accident.

[Tires degrade over time, even
when they are not being used.
Regardless of the remaining
tread, HYUNDAI recommends
that tires be replaced after six (6)
years of normal service.

[When replacing tires, it is
recommended to replace the
two front or two rear tires as a
pair. Replacing just one tire can
seriously affect your vehicle’s
handling. If only replacing one
pair of tires, it is recommended
to install the pair of new tires on
the rear axle.

[Heat caused by hot climates or
frequent high loading conditions
can accelerate the aging process.
Failure to follow this warning
may cause sudden tire failure,
which could lead to a loss of
vehicle control resulting in an
accident.

Maintenance
8-40
Instrument Panel Fuse
Replacement
OQX089024L
1. Turn the engine off.
2. Turn all other switches OFF.
3. Open the fuse panel cover.
4. Refer to the label on the inside of
the fuse panel cover to locate the
suspected fuse location.
OQXI079022
5. Pull the suspected fuse straight out.
Use the removal tool provided in the
engine compartment fuse panel.
6. Check the removed fuse; replace it if
it is blown. Spare fuses are provided in
the instrument panel fuse panels (or in
the engine compartment fuse panel).7. Push in a new fuse of the same
rating, and make sure it fits tightly in
the clips. If it fits loosely, consult an
authorized HYUNDAI dealer.
In an emergency, if you do not have a
spare fuse, use a fuse of the same rating
from a circuit you may not need for
operating the vehicle.
If the headlamps or other electrical
components do not work and the fuses
are undamaged, check the fuse panel
in the engine compartment. If a fuse is
blown, it must be replaced with the same
rating.
Fuse switch
OQX089036L
Always, place the fuse switch to the ON
position.
If you move the switch to the OFF
position, some items such as the audio
system and digital clock must be reset
and the smart key may not work properly.

08
8-45
Driver’s side fuse panel
Fuse Name (A) Circuit Protected
S/HEATER 20A Front Seat Warmer Control Module
MODULE 1 7.5A Stop Lamp Switch, ATM Shift Lever
MEMORY 2 7.5A SRS Control Module
AIR BAG 10A Passenger Occupant Detection Sensor, SRS Control Module
DOOR LOCK 20A Tail Gate Relay, T/Turn Unlock Realy, Door Lock/Unlock Realy
ECU 6 10A ECM, PCM
DRL 10A DRL Relay
MODULE 6 10A Data Link Connector, Key Interlock Solenoid
T/SIGNAL LAMP 15A IBU
MODULE 2 10ACrash Pad Switch, Multifunction Camera Unit, Blind Spot
Collision Warning Unit LH/RH
SUNROOF 15A Sunroof Motor
MODULE 3 7.5AConsole Switch, ATM Shift Lever Indicator, A/C Control Module,
Audio, Front Seat Warmer Control Module

Maintenance
8-46
Driver’s side fuse panel
Fuse Name (A) Circuit Protected
WIPER RR 15A E/R Junction Block (Wiper RR Relay), Rear Wiper Motor
WASHER 15A Multifunction Switch
A/BAG IND 7.5A Center Facia Switch, Instrument Cluster
IBU 2 7.5A IBU
ABS3 7.5AE/R Junction Block (Multipurpose Check Connector), ESC
Module
WIPER FRT 25A E/R Junction Block (Wiper FRT Low Relay), Front Wiper Motor
A/C 2 7.5A E/R Junction Block (Blower Relay), A/C Control Module
HEATED
STEERING15A Not Used
CLUSTER 7.5A Instrument Cluster
MODULE 7 10APower Outlet Relay, Power Outside Mirror Switch, IBU, Audio,
A/V & Navigation Head Unit
MDPS 2 7.5A MDPS Unit
MODULE 5 10A IBU, Front Seat Warmer Control Module
MODULE 4 7.5A IBU
A/C 3 7.5A Blower Motor, A/C Control Module

Maintenance
8-48
Engine compartment fuse panel
Fuse Name (A) Circuit Protected
MULTI
FUSEALT 125AAlternator, Multi Fuse - MDPS 1, Fuse - Rear Heated,
Blower, ABS 1, ABS 2
MDPS 1 80A MDPS Unit
FUSEREAR
HEATED40A ICU Junction Block (Rear Heated Relay)
ABS 1 40A Multipurpose Check Connector, ESC Module
ABS 2 40A ESC Module
BLOWER 40A Blower Relay
WIPER 10A Wiper FRT LO Realy, IBU
ECU2 15A ECM/PCM
ECU4 15A ECM/PCM
ECU5 15A ECM/PCM
IGN COIL 20A Ignition Coil #1~#4
INJECTOR 15A ECM/PCM, Injector #1~#4, Fuel Pump Relay
PTC HEATER 50A PTC Heater Relay
B+3 50AICU Junction Block (Fuse - DOOR LOCK, S/HEATER,
SAFETY P/WINDOW, SUNROOF, Power Window Relay)
IG2 40A Start Relay, PDM Relay Box (IG2 Relay), Ignition Switch