2022 HYUNDAI I20 Headlight

10-50
Maintenance
NOTICE
If you connect unauthorized electronic
devices to the battery, the battery may
be discharged. Never use unauthorized
devices.
Battery capacity label
OQXI079062OQXI079062
„„ Example Example
 The actual battery label in the vehicle
may differ from the illustration.
1. CMF45L-DIN : The HYUNDAI model
name of battery
2. 12V : The nominal voltage
3. 45Ah(20HR) : The nominal capacity (in
Ampere hours)
4. RC 80min : The nominal reserve
capacity (in min.)
5. CCA410 : The cold-test current in
amperes by SAE
6. 410A : The cold-test current in
amperes by EN
Battery recharging
Your vehicle has a maintenance-free,
calcium-based battery.
• If the battery becomes discharged in a
short time (because, for example, the
headlights or interior lights were left
on while the vehicle was not in use),
recharge it by slow charging (trickle)
for 10 hours.
• If the battery gradually discharges
because of high electric load while the
vehicle is being used, recharge it at
20-30A for two hours.
WARNING
Recharging battery
When recharging the battery, observe
the following precautions:
• The battery must be removed from
the vehicle and placed in an area with
good ventilation.
• Do not allow cigarettes, sparks, or
flame near the battery.
• Watch the battery during charging,
and stop or reduce the charging
rate if the battery cells begin
gassing (boiling) violently or if the
temperature of the electrolyte of any
cell exceeds 49°C (120°F).
• Wear eye protection when checking
the battery during charging.
• Disconnect the battery charger in the
following order.
1. Turn off the battery charger main
switch.
2. Unhook the negative clamp from the
negative battery terminal.
3. Unhook the positive clamp from the
positive battery terminal.

10-57
10
Compact spare tire replacement
(if equipped)
A compact spare tire has a shorter tread
life than a regular size tire. Replace
it when you can see the tread wear
indicator bars on the tire. The replaced
compact spare tire should be the same
size and design tire as the one provided
with your new vehicle and should be
mounted on the same compact spare
tire wheel. The compact spare tire is not
designed to be mounted on a regular
size wheel, and the compact spare tire
wheel is not designed to mount a regular
size tire.
Wheel replacement
When replacing the metal wheels for any
reason, make sure the new wheels are
equivalent to the original factory units in
diameter, rim width and offset.
WARNING
A wheel that is not the correct size may
adversely affect wheel and bearing life,
braking and stopping abilities, handling
characteristics, ground clearance,
body-to-tire clearance, snow chain
clearance, speedometer and odometer
calibration, headlight aim and bumper
height.
Tire traction
Tire traction can be reduced if you drive
on worn tires, tires that are improperly
inflated or on slippery road surfaces.
Tires should be replaced when tread
wear indicators appear. Slow down
whenever there is rain, snow or ice on
the road, to reduce the possibility of
losing control of the vehicle.

10-64
Maintenance
Instrument panel fuse
replacement
OBI3090014OBI3090014
1. Turn the vehicle off.
2. Turn all other switches OFF.
3. Open the fuse panel cover.
4. Refer to the label on the inside of
the fuse panel cover to locate the
suspected fuse location.
OBI3090016OBI3090016
5. Pull the suspected fuse straight out.
Use the removal tool provided in the
engine compartment fuses panel.
6. Check the removed fuse; replace it if
it is blown. Spare fuses are provided in
the instrument panel fuse panels (or in
the engine compartment fuse panel).
7. Push in a new fuse of the same rating,
and make sure it fits tightly in the
clips.If it fits loosely, we recommend
that you consult an authorized
HYUNDAI dealer.
In an emergency, if you do not have
a spare fuse, use a fuse of the same
rating from a circuit you may not need
for operating the vehicle, such as the
cigarette lighter fuse.
If the headlights or other electrical
components do not work and the fuses
are undamaged, check the fuse panel
in the engine compartment. If a fuse
is blown, it must be replaced with the
same rating.

10-77
10
We recommend that you consult an
authorized HYUNDAI dealer to replace
most vehicle light bulbs. It is difficult
to replace vehicle light bulbs because
other parts of the vehicle must be
removed before you can get to the bulb.
This is especially true for removing the
headlight assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to the
vehicle.
WARNING
Prior to replacing a light, depress the
foot brake, move the shift lever into the
N (Neutral, for Automatic transmission
vehicle) or neutral (for manual
transmission vehicle), apply the parking
brake, place the ignition switch in the
LOCK/OFF position, and take the key
with you when leaving the vehicle to
avoid sudden movement of the vehicle
and to prevent possible electric shock.
Be aware the bulbs may be hot and may
burn your fingers.
NOTICE
Be sure to replace the burned-out bulb
with one of the same wattage rating.
Otherwise, it may cause damage to the
fuse or electric wiring system.
i Information
The headlight and tail lamp lenses could
appear frosty if the vehicle is washed after
driving or the vehicle is driven at night
in wet weather. This condition is caused
by temperature difference between the
lamp inside and outside and, it does not
indicate a problem with your vehicle.
When moisture condenses in the lamp,
it will be removed after driving with the
headlight on. The removable level may
differ depending on lamp size, lamp
position and environmental condition.
However, if moisture is not removed, we
recommend that your vehicle is inspected
by an authorized HYUNDAI dealer.
LIGHT BULBS

10-78
Maintenance
Headlight, Position Light,
Turn signal Light bulb
replacement
Type A
OBI3090023OBI3090023
(1) Headlight(Low/High)
(2) Turn signal light
(3) Position light(if equipped)
(4) Daytime running light
(5) Fog light
*1 : MFR (Multi Focus Reflector) Headlight
OLMB073042LOLMB073042L
WARNING
• Handle halogen bulbs with care.
Halogen bulbs contain pressurized
gas that will produce flying pieces
of glass that could cause injuries if
broken.
• Wear eye protection when changing
a bulb. Allow the bulb to cool down
before handling it.• Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids.
• Never touch the glass with bare
hands. Residual oil may cause the bulb
to overheat and burst when lit.
• A bulb should be operated only when
installed in a headlight.
• If a bulb becomes damaged or
cracked, replace it immediately and
carefully dispose of it.
i Information
We recommend that the headlight aiming
be adjusted after an accident or after the
headlight assembly is reinstalled.

10-79
10
Headlight (Low/High) & Position
Light
1. Turn the front wheel at inwards.
OAC3089042TUOAC3089042TU
OAC3089043TUOAC3089043TU
OBC3090055OBC3090055
2. Remove retainers available on under
cover bottom area in the respective
side of headlight for bulb A/S.
3. Remove Wheel guard clips (B),
bumper cover bolt (A) and bumper
upper cover blot (C1) & retainer (C2).
OBC3090038OBC3090038
4. Pushing the Wheel guard aside & pull
front bumper near fender to unlock
front bumper with bumper bracket
near to headlight.
5. Remove the headlight bulb cover by
turning it counter-clockwise from bulb
assembly.
6. Remove the bulb from the headlight
assembly.
7. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8. Connect the headlight bulb socket
connector.
9. Install the headlight bulb cover by
turning it clockwise.
10. Install the wheel guard in the reverse
order.

10-81
10
Type B
OBI3090024OBI3090024
(1) Headlight(Low/High)
(2) Static Bending Light
(3) Daytime running light & Position light
(4) Turn signal light
(5) Front fog light
Headlight, Position light, Daytime
running light replacement
If not LED lamp does not operate,
we recommend that the system be
inspected by an authorized HYUNDAI
dealer. The LED lamps cannot be
replace as a single unit because it is an
integrated unit. The LED lamp has to be
replaced with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.
Low beam assist static light
1. Turn the front wheel at inwards.
OAC3089042TUOAC3089042TU
OAC3089043TUOAC3089043TU
OBC3090055OBC3090055
2. Remove retainers available on under
cover bottom area in the respective
side of headlight for bulb A/S.
3. Remove Wheel guard clips (B),
bumper cover bolt (A) and bumper
upper cover blot (C1) & retainer (C2).

10-82
Maintenance
OBC3090038OBC3090038
4. Pushing the Wheel guard aside & pull
front bumper near fender to unlock
front bumper with bumper bracket
near to headlight.
5. Remove the headlight bulb cover by
turning it counter-clockwise from bulb
assembly.
6. Remove the bulb from the headlight
assembly.
7. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8. Connect the headlight bulb socket
connector.
9. Install the headlight bulb cover by
turning it clockwise.
10. Install the wheel guard in the reverse
order.
„„Front Fog lightFront Fog light
OBI3090025OBI3090025
Fog light (if equipped)
1. Remove the under cover by rotating
the screws and bolts.
2. Reach your hand into the back of the
front bumper.
3. Disconnect the power connector from
the socket.
4. Remove the bulb-socket from
the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the
socket.
7. Reinstall the front bumper under
cover.