2022 HYUNDAI I20 climate control

6-63
06
Automatic heating and air
conditioning
The Automatic Climate Control System
is controlled by setting the desired
temperature.
OBI3050116OBI3050116
1. Press the AUTO button.
The modes, fan speeds, air intake and
air-conditioning will be controlled
automatically by the temperature setting
you select.
OBI3050114OBI3050114
2. Push the temperature control switch
to set the desired temperature. If
the temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.To turn the automatic operation off,
select any button of the following:
- Mode selection button
- Front windshield defrost button (Press
the button one more time to deselect
the front windshield defroster function.
- Fan speed control button
The selected function will be controlled
manually while other functions operate
automatically.
For your convenience and to improve
the effectiveness of the climate control,
use the AUTO button and set the
temperature to 23°C (73°F).
i Information
OBI3050027OBI3050027
Never place anything near the sensor
located to ensure better control of the
heating and cooling system.

6-66
Convenient features
OBI3050103OBI3050103
Instrument panel vents
You can adjust the direction of air
delivered from these vents using the
vent control lever as shown.
Temperature control
OBI3050114OBI3050114
The temperature will increase by
pushing the switch to up.
The temperature will decrease by
pushing the switch to down.
The temperature will increase or
decrease by 0.5°C (1°F) for each
incremental location. When set to the
lowest temperature setting, the air
conditioning will operate continuously.
Temperature conversion
If the battery has been discharged or
disconnected, the temperature mode
display will reset to Centigrade.
To change the temperature unit from °C
to °F or °F to °C :
- Automatic climate control system
Press the AUTO button for 3 seconds
while pressing the OFF button.
- Instrument cluster
Go to User Settings o Units o
Temperature Unit.
The temperature unit on both the cluster
LCD display and the climate control
screen will change.

6-67
06
Air intake control
OBI3050108OBI3050108
The air intake control button is used to
select either Fresh mode (outside air) or
Recirculation mode (cabin air).
Recirculated air position
The indicator light on the
button illuminates when
the recirculated air
position is selected.
With the recirculated air
position selected, air from
the passenger
compartment will be
drawn through the climate
control system and heated
or cooled according to the
function selected.
Outside (fresh) air position
The indicator light on the
button will turn off when
the outside (fresh) air
position is selected.
With the outside (fresh) air
position selected, air
enters the vehicle from
outside and is heated or
cooled according to the
function selected.
i Information
Operating the system primarily in Fresh
mode is recommended. Use Recirculation
mode temporarily only when needed.
Prolonged operation of the heater in
Recirculation mode and without the A/C
ON can cause fogging of the windshield.
In addition, prolonged use of the A/C
ON in Recirculation mode may result in
excessively dry, dehumidified air in the
cabin and may promote formation of
musty vent odor due to stagnant air.
WARNING
• Continued use of the climate control
system operation in the recirculated
air position can cause drowsiness
or sleepiness, that may cause loss
of vehicle control resulting in an
accident. Set the air intake control to
the outside (fresh) mode as much as
possible while driving.
• Continued use of the climate
control system operation in the
recirculated air position (without
the air conditioning selected) may
allow humidity to increase inside the
vehicle which may fog the glass and
obscure visibility.
• Do not sleep in a vehicle with air
conditioning or heating system on. It
may cause serious harm or death due
to a drop in the oxygen level and/or
body temperature.

6-68
Convenient features
Fan speed control
OBI3050107OBI3050107
Push the switch to up to increase the fan
speed and airflow. Push the switch to
down to decrease fan speed and airflow.
NOTICE
Operating the fan speed when the
ignition switch is in the ON position
could cause the battery to discharge.
Operate the fan speed when the engine
is running.
Air conditioning
OBI3050106OBI3050106
Push the A/C button to manually turn
the system on (indicator light will
illuminate) and off.
OFF mode
OBI3050117OBI3050117
Push the OFF button to turn off the
climate control system. You can still
operate the mode and air intake buttons
with the ignition switch in the ON
position.

6-71
06
System maintenance
Climate control air filter
OIK047401LOIK047401L
[A] : Outside air, [B] : Recirculated air
[C] : Climate control air filter, [D] : Blower
[E] : Evaporator core, [F] : Heater core
This filter is installed behind the glove
box. It filters the dust or other pollutants
that enter the vehicle through the
heating and air conditioning system.
We recommend that the climate control
air filter be replaced by an authorized
HYUNDAI dealer according to the
maintenance schedule. If the vehicle is
being driven in severe conditions such
as dusty or rough roads, more frequent
climate control filter inspections and
changes are required.
If the air flow rate suddenly decreases,
we recommend the system be checked
at an authorized HYUNDAI dealer.
i Information
• Replace the filter according to the
Maintenance Schedule.
• If the car is being driven in severe
conditions such as dusty, rough roads,
more frequent climate control air filter
inspections and changes are required.
• When the air flow rate suddenly
decreases, we recommend that the
system be checked by an authorized
HYUNDAI dealer.
Checking the amount of air
conditioner refrigerant and
compressor lubricant
When the amount of refrigerant is low,
the performance of the air conditioning
is reduced. Overfilling also has a bad
influence on the air conditioning system.
Therefore, if abnormal operation is
found, we recommend that the system
be inspected by an authorized HYUNDAI
dealer.
NOTICE
It is important that the correct type and
amount of oil and refrigerant is used.
Otherwise, damage to the compressor
and abnormal system operation may
occur. To prevent damage, the air
conditioning system in your vehicle
should only be serviced by trained and
certified technicians.
WARNING
Vehicles equipped with R-134a
Since the refrigerant is
operated at very high
pressure, the air
conditioning system should
only be serviced by trained
and certified technicians.
All refrigerants should be reclaimed
with proper equipment.
Venting refrigerants directly to the
atmosphere is harmful to individuals
and environment. Failure to heed these
warnings can lead to serious injuries.

6-72
Convenient features
WARNING
Do not use the or position
during cooling operation in extremely
humid weather. The difference
between the temperature of the
outside air and that of the windshield
could cause the outer surface of the
windshield to fog up, causing loss of
visibility. Set the mode selection to the
position and fan speed control to a
lower speed.
• For maximum defrosting, set the
temperature control to the extreme
right/hot position and the fan speed
control to the highest speed.
• If warm air to the floor is desired while
defrosting or defogging, set the mode
to the floor-defrost position.
• Before driving, clear all snow and ice
from the windshield, rear window,
outside rear view mirrors, and all side
windows.
• Clear all snow and ice from the hood
and air inlet at the buttom of the
windshield.
i Information
If the engine temperature is still cold after
starting, then a brief engine warm up
period may be required for the vented air
flow to become warm or hot.
Manual climate control system
To defog inside windshield
OBI3050111OBI3050111
1. Select desired fan speed.
2. Select desired temperature.
3. Select the
or position.
4. The outside (fresh) air will be selected
automatically. Additionally, the
air conditioning will automatically
operate if the mode is selected to the
or position.
If the air conditioning and outside (fresh)
mode are not selected automatically,
press the corresponding button
manually.
WINDSHIELD DEFROSTING AND DEFOGGING

6-73
06
To defrost outside windshield
OBI3050112OBI3050112
1. Set the fan speed to the highest
(extreme right) position.
2. Set the temperature to the extreme
hot position.
3. Select the
position.
4. The outside (fresh) mode and
air conditioning will be selected
automatically.
Automatic climate control
system
To defog inside windshield
OBI3050105OBI3050105
1. Select desired blower speed.
2. Select desired temperature.
3. Press the defroster button (
).
4. The air-conditioning will turn on
according to the detected ambient
temperature, fresh mode and higher
blower speed will be selected
automatically.
If the air-conditioning, fresh mode and
higher blower speed are not selected
automatically, adjust the corresponding
button or knob manually.
If the
position is selected, lower
blower speed is controlled to higher
blower speed.

6-74
Convenient features
To defrost outside windshield
OBI3050118OBI3050118
1. Set blower speed to the highest
position.
2. Set temperature to the extreme hot
(HI) position.
3. Press the defroster button (
).
4. The air-conditioning will turn on
according to the detected ambient
temperature and fresh mode will be
selected automatically.
If the
position is selected, lower
blower speed is controlled to higher
blower speed.
Auto defogging system (only
for automatic climate control
system, if equipped)
OBC3050124OBC3050124
Auto defogging helps reduce the
possibility of fogging up the inside of the
windscreen by automatically sensing the
moisture on inside the windscreen.
The auto defogging system operates
when the heater or air conditioning is on.
When the Auto Defogging
System operates, the indicator
will illuminate.
If a high amount of humidity is detected
in the vehicle, the Auto Defogging
System will be enabled.
The following steps will be performed
automatically:
Step 1) The A/C button will turn ON.
Step 2) The air intake control will change
to Fresh mode under low outside
temperature.
Step 3) The mode will be changed to
defrost to direct airflow to the
windscreen.
Step 4) The blower speed will be
increased.