2022 HYUNDAI I20 change time

6-60
Convenient features
Air conditioning system operation tips
• If the vehicle has been parked in direct
sunlight during hot weather, open the
windows for a short time to let the hot
air inside the vehicle escape.
• After sufficient cooling has been
achieved, switch back from
recirculation mode to fresh mode.
• To help reduce moisture inside of
the windows on rainy or humid
days, decrease the humidity inside
the vehicle by operating the air
conditioning system with the windows
and sunroof closed.
• During air conditioning system
operation, you may occasionally
notice a slight change in engine speed
as the air conditioning compressor
cycles. This is a normal system
operation characteristic.
• Use the air conditioning system
every month only for a few minutes
to ensure maximum system
performance.
• When using the air conditioning
system, you may notice clear water
dripping (or even puddling) on the
ground under the passenger side of
the vehicle. This is a normal system
operation characteristic.
• If you operate the air conditioner
excessively, the difference between
the temperature of the outside air and
that of the windshield could cause the
outer surface of the windshield to fog
up, causing loss of visibility. In this
case, set the mode selection button to
the
position and set the fan speed
control knob to the lowest speed
setting.
System maintenance
Climate control air filter
OIK047401LOIK047401L
[A] : Outside air, [B] : Recirculated air
[C] : Climate control air filter, [D] : Blower
[E] : Evaporator core, [F] : Heater core
This filter is installed behind the glove
box. It filters the dust or other pollutants
that enter the vehicle through the
heating and air conditioning system.
We recommend that the climate control
air filter be replaced by an authorized
HYUNDAI dealer according to the
maintenance schedule. If the vehicle is
being driven in severe conditions such
as dusty or rough roads, more frequent
climate control filter inspections and
changes are required.
If the air flow rate suddenly decreases,
we recommend the system be checked
at an authorized HYUNDAI dealer.
i Information
• Replace the filter according to the
Maintenance Schedule.
• If the car is being driven in severe
conditions such as dusty, rough roads,
more frequent climate control air filter
inspections and changes are required.
• When the air flow rate suddenly
decreases, we recommend that the
system be checked by an authorized
HYUNDAI dealer.

6-70
Convenient features
NOTICE
• The refrigerant system should only
be serviced by trained and certified
technicians to insure proper and safe
operation.
• The refrigerant system should be
serviced in a well-ventilated place.
• The air conditioning evaporator
(cooling coil) shall never be repaired
or replaced with one removed from
a used or salvaged vehicle and new
replacement MAC evaporators shall
be certified (and labeled) as meeting
SAE Standard J2842.
i Information
• When using the air conditioning system,
monitor the temperature gauge closely
while driving up hills or in heavy traffic
when outside temperatures are high.
Air conditioning system operation may
cause engine overheating. Continue
to use the blower fan but turn the
air conditioning system off if the
temperature gauge indicates engine
overheating.
• When opening the windows in humid
weather, air conditioning may create
water droplets inside the vehicle. Since
excessive water droplets may cause
damage to electrical equipment, air
conditioning should only be used with
the windows closed.
Air conditioning system operation tips
• If the vehicle has been parked in direct
sunlight during hot weather, open the
windows for a short time to let the hot
air inside the vehicle escape.
• After sufficient cooling has been
achieved, switch back from
recirculation mode to fresh mode.
• To help reduce moisture inside of
the windows on rainy or humid
days, decrease the humidity inside
the vehicle by operating the air
conditioning system with the windows
and sunroof closed.
• During air conditioning system
operation, you may occasionally
notice a slight change in engine speed
as the air conditioning compressor
cycles. This is a normal system
operation characteristic.
• Use the air conditioning system
every month only for a few minutes
to ensure maximum system
performance.
• When using the air conditioning
system, you may notice clear water
dripping (or even puddling) on the
ground under the passenger side of
the vehicle. This is a normal system
operation characteristic.
• If you operate the air conditioner
excessively, the difference between
the temperature of the outside air and
that of the windshield could cause the
outer surface of the windshield to fog
up, causing loss of visibility. In this
case, set the mode selection button to
the
position and set the fan speed
control knob to the lowest speed
setting.

6-96
Convenient features
System layout – steering wheel
remote control
(Bluetooth® equipped model)
ÃThe system’s actual appearance and
layout may differ depending on the
car model and specification.
(1) MUTE button
• Press to mute or unmute the
system.
• During a call, press to mute or
unmute the microphone.
• While playing media, press to pause
or resume playback. (if equipped)
(2) MODE button
• Press to switch between radio and
media modes.
• If no media is connected, each time
this is pressed, it toggles between
the radio modes (FM X AM X FM).
• Press and hold to turn the system
on or off.
(3) Volume lever
• Push up or down to adjust the
volume.(4) Up/Down lever
• Change the station/track/file.
• While listening to the radio, push
to listen to the previous/next saved
radio station.
• While listening to the radio, push
and hold to search for a station.
• While playing media, push and hold
to rewind or fast forward (except for
the Bluetooth audio mode).
• While playing media push to listen
to the previous/next song.
(5) Call/Answer button
• Press to start connecting a mobile
phone via Bluetooth.
• After a Bluetooth phone connection
is made, press to access your call
history. Press and hold to dial the
most recent phone number. When
a call comes in, press to answer the
call.
• During a call, press to switch
between the active call and the held
call. Press and hold to switch the
call between the system and the
mobile phone.
• In 3-way call, swaps between calls.
(6) Call end button
• When a call comes in, reject the call.
• During a call, end the call.

6-98
Convenient features
i Information
- About handling the system
• Do not apply excessive force to the
system. Excessive pressure on the
screen may damage the LCD panel or
the touch panel.
• When cleaning the screen or button
panel, make sure to stop the engine
and use a soft, dry cloth. Wiping the
screen or buttons with a rough cloth or
using solvents (alcohol, benzene, paint
thinner, etc.) may scratch or chemically
damage the surface.
• If you attach a liquid-type air freshener
to the fan louvre, the surface of the
louvre may become deformed due to
the flowing air.
• If you want to change the position of
the installed device, please inquire
with your place of purchase or service
maintenance centre. Technical expertise
is required to install or disassemble the
device.
NOTICE
• If you experience any problems with
the system, contact your place of
purchase or dealer.
• Placing the audio system within an
electromagnetic environment may
result in noise interference.
Turning the system on or off
To turn on the system, start the engine.
• If you do not want to use the system
while driving, you can turn off the
system by pressing the [POWER]
button on the control panel. To use
the system again, press the [POWER]
button again.
After you have turned off the engine, the
system will automatically turn off after a
while or as soon as you open the driver’s
door.
• Depending on the vehicle model or
specifications, the system may turn
off as soon as you turn off the engine.
• When you turn back on the system,
the previous mode and settings will
remain intact.
WARNING
• Some functions may be disabled for
safety reasons while the vehicle is
moving. They work only when the
vehicle stops. Park your vehicle in
a safe location before using any of
them.
• Stop using the system if it
malfunctions, such as no audio
output or display. If you continue
using the system when it is
malfunctioning, it may lead to a fire,
electric shock, or system failure.
i Information
You can turn on the system when the key
ignition switch is placed in the “ACC”
or “ON” position. Using the system for
an extended period without the engine
running drains the battery. If you plan on
using the system for a long time, start the
engine.

6-100
Convenient features
5$',2
Turning on the radio
1. On the control panel, press the
[AUDIO] button.
2. When the mode selection window
displays, turn the [TUNE] knob to
select the desired radio mode and
then press the knob.
FM/AM Mode
(1) Current radio mode
(2) Radio station information
(3) Preset list
Press the [MENU/CLOCK] button on the
control panel to access the following
menu options:
• Autostore: Save radio stations to the
preset list.
• Scan: The system searches for radio
stations with strong radio signals and
plays each radio station for about five
seconds.
• Sound settings: You can change
the settings related to sounds, such
as location where sound will be
concentrated and the output level for
each range.
-Position: Select a location where
sound will be concentrated in the
vehicle. Select Fader or Balance,
turn the [TUNE] knob to select the
desired position, and then press the
knob. To set sound to be centred in
the vehicle, select Centre.
-Equaliser: Adjust the output level
for each sound tone mode.
-Sound experience: Select the
location where sound is focused
in the vehicle between the driver’s
seat and all other seats.
-Speed dependent vol.: Set the
volume to be adjusted automatically
according to your driving speed.
NOTICE
• Depending on vehicle models or
specifications, available options may
vary.
• Depending on the system or
amplifier specifications applied to
your vehicle, available options may
vary.
• Mode popup: Set to display mode
selection window when the [AUDIO]
button is pressed on the control panel.
• Bluetooth remote lock: Even if
Bluetooth remote control application
is connected, if Set Bluetooth remote
lock is enabled. System cannot be
operated via smart phone application.
• Date/Time: You can change the
date and time that are shown on the
system display.
-Set date: Set date to display on the
system display.
-Set time: Set time to display on the
system display.
-Time format: Select to display time
in the 12 hour format or the 24 hour
format.
- Display (Power Off): Set to display
the clock when the system power is
off.
• Language: You can change the
display language.

6-101
06
Changing the radio mode
1. On the control panel, press the
[AUDIO] button.
2. When the mode selection window
displays, turn the [TUNE] knob to
select the desired radio mode and
then press the knob.
• Each time you press the [MODE]
button on the steering wheel, the
radio mode switches to FM X AM
in order.
NOTICE
When the Mode popup is not selected
in [MENU/CLOCK] X Mode popup, press
the [AUDIO] button on the control panel
to change the radio mode.
Each time you press the [AUDIO] button
on the control panel, the radio mode
switches to FM X AM in order.
Scanning for available radio
stations
You can listen to each radio station for
a few seconds to test the reception and
select the one you want.
1. From the radio screen, press the
[MENU/CLOCK] button on the control
panel.
2. When the option selection window
displays, turn the [TUNE] knob to
select Scan, and then press the knob.
• The system searches for radio
stations with strong radio signals
and plays each radio station for
about five seconds.
3. When you find the radio station you
want to listen to, press the [TUNE]
knob.
• You can continue listening to the
selected station.
•
Searching for radio stations
To search for the previous or next
available radio station, press the
[< SEEK] button / [TRACK >] button on
the control panel.
• You can also press and hold the
[< SEEK] button / [TRACK >] button
to search for frequencies quickly.
When you release the button, a radio
station with a strong signal is selected
automatically.
If you know the exact frequency of the
radio station you want to listen to, turn
the [TUNE] knob on the control panel to
change the frequency.

6-103
06
0(',$3/$<(5
Using the media player
You can play music stored in various
media storage devices, such as USB
storage devices, smartphones.
1. Connect a device to the USB port in
your vehicle.
• Playback may start immediately
depending on the device that you
connect to the system.
2. On the control panel, press the
[AUDIO] button.
3. When the mode selection window
displays, turn the [TUNE] knob to
select the desired mode and then
press the knob.
NOTICE
• To start the media player, press the
[AUDIO] button on the control panel.
• You can also change the mode by
press the [MODE] button repeatedly
on the steering wheel.
• Make sure to connect or disconnect
external USB devices with the system
power turned off.
• When the Mode popup is not
selected in [MENU/CLOCK] X Mode
popup, press the [AUDIO] button
on the control panel to change the
media player.
Each time you press the [AUDIO]
button on the control panel, the
media mode switches to USB X
Bluetooth audio in order.
• Depending on vehicle models and
specifications, available buttons or
the appearance and layout of the
USB port in your vehicle may vary.• Do not connect a smartphone or
an MP3 device to the system via
multiple methods such as USB and
Bluetooth simultaneously. Doing
so may cause a distorted noise or a
system malfunction.
• When the equaliser function of the
connected device and Equaliser
settings of the system are both
activated, the effects may interfere
with each other and may lead to
sound degradation or distortion.
Deactivate the device’s equaliser
function if possible.
Using the USB mode
You can play media files stored in
portable devices, such as USB storage
devices and MP3 players. Check
compatible USB storage devices and
file specifications before using the USB
mode.
Connect your USB device to the USB port
in the vehicle.
• Playback starts immediately.
• Press the [AUDIO] button on the
control panel to display the mode
selection window, turn the [TUNE]
knob to select USB and then press the
knob.

6-104
Convenient features
(1) Current file number and total number
of files
(2) Playback time
(3) Information about the song currently
playing
Press the [MENU/CLOCK] button on the
control panel to access the following
menu options:
• List: Access the file list.
• Folder list: Access the folder list.
• Information: Display information
about the song currently playing.
• Sound settings: You can change
the settings related to sounds, such
as location where sound will be
concentrated and the output level for
each range.
-Position: Select a location where
sound will be concentrated in the
vehicle. Select Fader or Balance,
turn the [TUNE] knob to select the
desired position, and then press the
knob. To set sound to be centred in
the vehicle, select Centre.
-Equaliser: Adjust the output level
for each sound tone mode.
-Sound experience: Select the
location where sound is focused
in the vehicle between the driver’s
seat and all other seats.
-Speed dependent vol.: Set the
volume to be adjusted automatically
according to your driving speed.
NOTICE
• Depending on vehicle models or
specifications, available options may
vary.
• Depending on the system or
amplifier specifications applied to
your vehicle, available options may
vary.
• Song information: Select information
such as Folder/File or Artist/Title/
Album to display when playing MP3
files.
• Mode popup: Set to display mode
selection window when the [AUDIO]
button is pressed on the control panel.
• Bluetooth remote lock: Even if
Bluetooth remote control application
is connected, if Set Bluetooth remote
lock is enabled. System cannot be
operated via smart phone application.
• Date/Time: You can change the
date and time that are shown on the
system display.
-Set date: Set date to display on the
system display.
-Set time: Set time to display on the
system display.
-Time format: Select to display time
in the 12 hour format or the 24 hour
format.
-Display (Power Off): Set to display
the clock when the system power
is off.
• Language: You can change the
display language.
Rewinding/Fast forwarding
On the control panel, press and hold the
[< SEEK] button / [TRACK >] button.
• You can also push and hold the Up/
down lever on the steering wheel.