2022 HYUNDAI I10 instrument cluster

4-22
Instrument cluster
Door, Bonnet, Tailgate open
indicator
OAC3079037R
This warning is displayed indicating
which door, bonnet, or tailgate is
open.
CAUTION
Before driving the vehicle, you
should confirm that the door/ bon-
net/tailgate is fully closed. Also,
check there is no door/bonnet/tail-
gate open warning light or mes-
sage displayed on the instrument
cluster.
Turn on FUSE SWITCH
This warning message is displayed if
the fuse switch located on the fuse
box under the steering wheel is OFF.
You should turn the fuse switch on.
For more details, refer to “Fuses”
in chapter 8.

4-24
Instrument cluster
Low engine oil (if equipped)
This warning message is displayed
when the engine oil level should be
checked.
If this warning message is displayed,
check the engine oil level as soon as
possible and add engine oil as
required.
Slowly pour the recommended oil lit-
tle by little into a funnel. (Oil refill
capacity : approximately 0.15 ~ 0.26
gal. (0.6 ~ 1.0 l)
Use only the specified engine oil.
(Refer to "Recommended lubricants
and capacities" in chapter 8.)
Do not overfill the engine oil. Make
sure the oil level is not above F (Full)
mark on the dipstick.
NOTICE
If the message is displayed contin-
uously after adding the engine oil
and travelling approximately
50~100 km after the engine warms
up, we recommend that the system
be checked by a HYUNDAI autho-
rised repairer.
Engine has overheated
(if equipped)
This warning message is displayed
when the engine coolant temperature
is above 120°C (248°F). This means
that the engine is overheated and
may be damaged.
If your vehicle is overheated, refer
to “Overheating” in chapter 7.
Check headlight (if equipped)
This warning message is displayed if
the headlamps are not operating
properly.
In addition, if a specific lamp(turn sig-
nal lamp etc.) is not operating proper-
ly, the warning message according to
a specific lamp (turn signal lamp etc.)
is displayed. A corresponding bulb
may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same watt-
age rating.
Check brake light (if equipped)
This warning message is displayed if
the stop lamps are not operating
properly. A lamp may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same watt-
age rating.

4-26
Instrument cluster
LCD DISPLAY
LCD display control
The LCD display modes can be changed by using the control buttons.
(1)
: MODE button for changing modes
(2)
, : MOVE switch for changing items
(3) OK : SELECT/RESET button for setting or resetting the selected item
OAC3059002TU

4-28
Instrument cluster
Trip computer mode
OAC3069039R
The trip computer mode displays
information related to vehicle driving
parameters including fuel economy,
tripmeter information and vehicle
speed.
For more details, refer to "Trip
Computer" in this chapter.
Driving Assist mode
OAC3069013TU
L.A/'AW/ISLW
This mode displays the state of the
Lane Keeping Assist, Driver Attention
Warning and Intelligent Speed Limit
Warning.
For more details, refer to each sys-
tem information in chapter 6.
Master warning mode
OAC3069028TU
This warning light informs the driver
the following situations.
- Forward Collision-Avoidance Assist
system malfunction (if equipped)
- Forward Collision-Avoidance Assist
radar blocked (if equipped)
- Lamp malfunction (if equipped)
- High Beam Assist malfunction (if
equipped)
- Tyre Pressure Monitoring System
(TPMS) malfunction (if equipped)
The Master Warning Light illuminates
if one or more of the above warning
situations occur.
At this time, a Master Warning icon (
)
will appear beside the User Settings
icon (
), on the LCD display.
If the warning situation is solved, the
master warning light will be turned off
and the Master Warning icon will dis-
appear.

4-29
04
User settings mode
In this mode, you can change the set-
tings of the instrument cluster, doors,
lamps, etc.
1. Driver Assistance
2. Lights
3. Door
4. Convenience
5. Service interval
6. Other Features
7. Language
8. Reset
The information provided may dif-
fer depending on which functions
are applicable to your vehicle.
(ngage parking brake to edit set-
tings
This warning message illuminates if
you try to select an item from the User
Settings mode whilst driving.
For your safety, change the User
Settings after parking the vehicle,
applying the parking brake and press-
ing the P (Park) button.
4uick guide (+elp)
This mode provides quick guides for
the systems in the User Settings
mode.
Select an item, press and hold the
OK button.
For more details about each sys-
tem, refer to this Owner’s Manual.

4-30
Instrument cluster
1. 'river Assistance
ItemsExplanation
Driver Assist

4-32
Instrument cluster
5. Service interval
ItemsExplanation
Enable Service
IntervalTo activate or deactivate the service interval function.
Adjust IntervalIf the service interval menu is activated, you may adjust the time
and distance.
If the service interval is activated and the time and distance is adjusted, mes-
sages are displayed in the following situations each time the vehicle is turned
on.
- Service in: Displayed to inform the driver the remaining mileage and days to
service.
- Service required: Displayed when the mileage and days to service has been
reached or passed.
i Information
If any of the following conditions occur, the mileage and number of days to service
may be incorrect.
- 7he battery cable is disconnected.
- 7he fuse switch is turned off.
- 7he battery is discharged.
Ú
The information provided may differ depending on which functions are applica-
ble to your vehicle.

4-34
Instrument cluster
Trip computer
The trip computer is a microcomput-
er-controlled driver information sys-
tem that displays information related
to driving.
i Information
Some driving information stored in the
trip computer (for e[ample Average
9ehicle Speed) resets if the battery is
disconnected.
Trip modes
Fuel Economy