2022 HYUNDAI GENESIS GV70 display
[x] Cancel search: displayPage 322 of 647
Driving Your Vehicle
6-48
In the Auto Stop mode, if the engine
hood is opened, ISG system will be
deactivated.
When the system is deactivated, the ISG
off button indicator will illuminate and
a message ‘Auto Stop error. Shift to P or
N to start engine manually’ appears on
the cluster LCD display with a warning
sound.
If this occurs, depress the brake pedal
and restart the engine manually.
Auto start
When the engine stops automatically by
ISG, the engine will restart if one of the
following is done.
- Release the brake pedal.
- When Auto Hold is activated, take
your foot off the brake pedal and then
depress the accelerator pedal.
- While depressing the brake pedal,
shift the gear from N (Neutral) or D
(Drive) to R (Reverse) or P (Park).
- While depressing the brake pedal,
shift the gear from N (Neutral) to D
(Drive).
LCD display messages
The messages are displayed on the
instrument cluster to help use ISG
system.
OJK060068LOJK060068L
Auto stop error. Shift to P or N to start
engine manually
When the system is deactivated, the ISG
off button indicator will illuminate and
a message will appear on the cluster
LCD display with a warning sound in the
following situations.
- When the engine hood is opened.
- When ISG system is not working
normally.
If this occurs, depress the brake pedal
and restart the engine manually. For your
safety, restart the vehicle in the P (Park)
position.
Page 323 of 647
06
6-49
OJK060043OJK060043
AUTO STOP elapsed time
AUTO STOP display shows the elapsed
time of engine stop by the Idle Stop and
Go system.
You may check AUTO STOP elapsed time
in the Utility view on the instrument
cluster.
Refer to “View Modes” section in
chapter 4.
ISG System Off
OJK060016LOJK060016L
Press the ISG OFF button to turn off ISG
system. The ISG OFF button indicator will
illuminate. To use the system, press the
ISG OFF button again.
Page 386 of 647
07
7-37
Collision Warning
• Collision warning will operate when
the turn signal is turned on in the
direction of the detected vehicle.
• If ‘Warning Only’ is selected from the
Settings menu, the collision warning
will operate when your vehicle
approaches the lane the blind spot
vehicle is detected.
• To warn the driver of a collision, the
warning light on the side view mirror
and head-up display (if equipped) will
blink. At the same time, an audible
warning will sound and the steering
wheel will vibrate.
• When the turn signal is turned off or
you move away from the lane, the
collision warning will be canceled and
Blind-Spot Collision-Avoidance Assist
will return to vehicle detection state. : $ 5 1 , 1 *
• The detecting range of the rear
F R U Q H U U D G D U L V G H W H U P L Q H G E \ D
V W D Q G D U G U R D G Z L G W K W K H U H I R U H R Q
D Q D U U R Z U R D G % O L Q G 6 S R W & R O O L V L R Q
$ Y R L G D Q F H $ V V L V W P D \ G H W H F W R W K H U
Y H K L F O H V L Q W Z R O D Q H V R Y H U D Q G Z D U Q
\ R X , Q F R Q W U D V W R Q D Z L G H U R D G
% O L Q G 6 S R W & R O O L V L R Q $ Y R L G D Q F H
$ V V L V W P D \ Q R W E H D E O H W R G H W H F W D
Y H K L F O H G U L Y L Q J L Q W K H Q H [ W O D Q H D Q G
P D \ Q R W Z D U Q \ R X
• : K H Q W K H K D ] D U G Z D U Q L Q J I O D V K H U L V
R Q W K H F R O O L V L R Q Z D U Q L Q J E \ W K H W X U Q
V L J Q D O Z L O O Q R W R S H U D W H
Information
If the driver's seat is on the left side, the
collision warning may occur when you
turn left. Maintain a proper distance with
the vehicles in the left lane. If the driver's
seat is on the right side, the collision
warning may occur when you turn right.
Maintain a proper distance with the
vehicles in the right lane.
Page 387 of 647
Driver Assistance System
7-38
OJK070042LOJK070042L
Collision-Avoidance Assist (while driving)
• To warn the driver of a collision, the
warning light on the side view mirror
will blink and a warning message
will appear on the cluster. At the
same time, an audible warning will
sound, warning light on the head-up
display (if equipped) will blink and the
steering wheel will vibrate.
• Blind-Spot Collision-Avoidance Assist
will operate when your vehicle speed
is between 40~120 mph (60~200
km/h) and both lane markings of the
driving lane are detected.
• Emergency braking will be assisted to
help prevent collision with the vehicle
in the blind spot area.
: $ 5 1 , 1 *
• & R O O L V L R Q $ Y R L G D Q F H $ V V L V W Z L O O
E H F D Q F H O H G X Q G H U W K H I R O O R Z L Q J
circumstances:
- < R X U Y H K L F O H H Q W H U V W K H Q H [ W O D Q H
E \ D F H U W D L Q G L V W D Q F H
- < R X U Y H K L F O H L V D Z D \ I U R P W K H
collision risk
- 7 K H V W H H U L Q J Z K H H O L V V K D U S O \
steered
- 7 K H E U D N H S H G D O L V G H S U H V V H G
- ) R U Z D U G & R O O L V L R Q $ Y R L G D Q F H $ V V L V W
is operating
• $ I W H U % O L Q G 6 S R W & R O O L V L R Q $ Y R L G D Q F H
$ V V L V W R S H U D W L R Q R U F K D Q J L Q J O D Q H
\ R X P X V W G U L Y H W R W K H F H Q W H U R I W K H
O D Q H % O L Q G 6 S R W & R O O L V L R Q $ Y R L G D Q F H
$ V V L V W Z L O O Q R W R S H U D W H L I W K H Y H K L F O H L V
Q R W G U L Y H Q L Q W K H F H Q W H U R I W K H O D Q H
Page 388 of 647
07
7-39
OJK070079LOJK070079L
Collision-Avoidance Assist (while
departing)
• To warn the driver of a collision, the
warning light on the side view mirror
will blink and a warning message
will appear on the cluster. At the
same time, an audible warning will
sound, warning light on the head-up
display (if equipped) will blink and the
steering wheel will vibrate.
• Blind-Spot Collision-Avoidance Assist
will operate when your vehicle speed
is below 2 mph (3 km/h) and the
speed of the vehicle in the blind spot
area is above 3 mph (5 km/h).
• Emergency braking will be assisted to
help prevent collision with the vehicle
in the blind spot area.
OJK070026LOJK070026L
• When the vehicle is stopped due
to emergency braking, the ‘Drive
carefully’ warning message will
appear on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
• Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
Page 408 of 647
07
7-59
OJK071213NOJK071213N
(1) Speed Limit indicator
(2) Set speed
You can set the speed limit when you do
not want to drive over a specific speed.
If you drive over the preset speed limit,
Manual Speed Limit Assist will operate
(set speed limit will blink and chime will
sound) until the vehicle speed returns
within the speed limit.
Manual Speed Limit Assist
Operation
To set speed limit
OJK070082OJK070082
1. Press and hold Driving Assist
() button at the desired speed. The
Speed Limit () indicator will
illuminate on the cluster.
OJX1070152LOJX1070152L
2. Push the + switch up or - switch down,
and release it at the desired speed.
Push the + switch up or - switch down
and hold it. The speed will increase
or decrease to the nearest multiple of
five (multiple of ten in km/h) at first,
and then increase or decrease by 5
mph (10 km/h).
OJK071214NOJK071214N
3. The set speed limit will be displayed
on the cluster.
If you would like to drive over the
preset speed limit, depress the
accelerator pedal beyond the pressure
point to activate the kickdown
mechanism.
The set speed limit will blink and
chime will sound until you return the
vehicle speed within the speed limit.
0 $ 1 8 $ / 6 3 ( ( ' / , 0 , 7 $ 6 6 , 6 7
Page 413 of 647
Driver Assistance System
7-64
OJK071011N OJK071011N
Warning overspeed
When driving at a speed higher than the
displayed speed limit, the red speed limit
indicator will blink.
OJK071183NOJK071183NOJK071190NOJK071190N
Changing set speed
If the speed limit of the road changes
during the operation of Manual Speed
Limit Assist or Smart Cruise Control, an
arrow in the direction of up or down is
displayed to inform the driver that the set
speed needs to be changed. At this time,
the driver can change the set speed
according to the speed limit by using the
+ or – switch on the steering wheel.
: $ 5 1 , 1 *
• , I W K H 2 I I V H W L V D G M X V W H G R Y H U S T W K H
set speed will change to a higher
speed than the speed limit of the
U R D G , I \ R X Z D Q W W R G U L Y H E H O R Z W K H
V S H H G O L P L W D G M X V W W K H 2 I I V H W X Q G H U
'0' or use the – switch on the steering
Z K H H O W R O R Z H U W K H V H W V S H H G
• ( Y H Q D I W H U F K D Q J L Q J W K H V H W V S H H G
according to the speed limit of the
U R D G W K H Y H K L F O H F D Q V W L O O E H G U L Y H Q
R Y H U W K H V S H H G O L P L W , I Q H F H V V D U \
G H S U H V V W K H E U D N H S H G D O W R U H G X F H
\ R X U G U L Y L Q J V S H H G
• If the speed limit of the road is under
P S K N P K W K H V H W V S H H G
F K D Q J H I X Q F W L R Q Z L O O Q R W Z R U N
• Intelligent Speed Limit Assist
operates using the speed unit in the
L Q V W U X P H Q W F O X V W H U V H W E \ W K H G U L Y H U
If the speed unit is set to a unit other
W K D Q W K H V S H H G X Q L W X V H G L Q \ R X U
F R X Q W U \ , Q W H O O L J H Q W 6 S H H G / L P L W
$ V V L V W P D \ Q R W R S H U D W H S U R S H U O \
Information
• For more details on Manual Speed
Limit Assist operation, refer to
“Manual Speed Limit Assist (MSLA)”
section in this chapter.
• For more details on Smart Cruise
Control operation, refer to “Smart
Cruise Control (SCC)” section in this
chapter.
Page 418 of 647
07
7-69
• The driver’s attention level is displayed
on the scale of 1 to 5. The lower the
level is, the more inattentive the driver
is.
• The level decreases when the driver
does not take a break for a certain
period of time.
7 D N L Q J D E U H D N
OTM070105LOTM070105L
• The ‘Consider taking a break’ message
will appear on the cluster and an
audible warning will sound to suggest
that the driver take a break, when the
driver’s attention level is below 1.
• Driver Attention Warning will not
suggest a break when the total driving
time is shorter than 10 minutes or 10
minutes has not passed after the last
break was suggested.
: $ 5 1 , 1 *
) R U \ R X U V D I H W \ F K D Q J H W K H 6 H W W L Q J V
D I W H U S D U N L Q J W K H Y H K L F O H D W D V D I H
O R F D W L R Q
& $ 8 7 , 2 1
• ' U L Y H U $ W W H Q W L R Q : D U Q L Q J P D \
V X J J H V W D E U H D N G H S H Q G L Q J R Q W K H
G U L Y H UT V G U L Y L Q J S D W W H U Q R U K D E L W V
H Y H Q L I W K H G U L Y H U G R H V QT W I H H O I D W L J X H
• ' U L Y H U $ W W H Q W L R Q : D U Q L Q J L V D
V X S S O H P H Q W D O I X Q F W L R Q D Q G P D \ Q R W
E H D E O H W R G H W H U P L Q H Z K H W K H U W K H
G U L Y H U L V L Q D W W H Q W L Y H
• 7 K H G U L Y H U Z K R I H H O V I D W L J X H G V K R X O G
W D N H D E U H D N D W D V D I H O R F D W L R Q H Y H Q
W K R X J K W K H U H L V Q R E U H D N V X J J H V W L R Q
E \ ' U L Y H U $ W W H Q W L R Q : D U Q L Q J
Information
• For more details on setting the
functions in the infotainment system,
refer to “Vehicle Settings” section in
chapter 4.
• Driver Attention Warning will reset the
last break time to 00:00 in the following
situations:
-The engine is turned off
-The driver unfastens the seat belt
and opens the driver’s door
-The vehicle is stopped for more than
10 minutes
• When the driver resets Driver Attention
Warning, the last break time is set to
00:00 and the driver’s attention level is
set to High.