2022 HYUNDAI GENESIS G70 ESP

09
9-53
Engine compartment fuse panel
Fuse NameFuse Rating Circuit Protected
ALT175A
225AAlternator, Fuse - F2,
Multi Fuse 1 - F4, F6, F7, F8, F9, F10, F11, F12, F13
C/FAN3
125A[G6DP - BLDC Motor] Cooling Fan Controller
GLOW[D4HB] Glow Relay Unit
START30A RLY. 7 (Start Relay)
C/FAN180A [BLDC Motor] Cooling Fan Controller
B+350AICU Junction Block (Fuse - F5, Leak Current Autocut
Device Fuse - F2, F4, F13, F14, F21, F22)
B+250A ICU Junction Block (Fuse - F27, F35, F43, F51, F52)
B+150A ICU Junction Block (Fuse - F28, F29, F37, F45, F53)
EOP50A [With ISG] Electric Oil Pump Module
ESP140A ESP Control Module
ESP240A ESP Control Module
BLOWER40A RLY. 6 (Blower Relay)
IG230A PCB Block (IG2 Relay)
MDPS100A MDPS Unit
B+460APCB Block
(Engine Control Relay, Fuse - F4, F5, F13, F22)
C/FAN260A [DC Motor] RLY. 9 (Cooling Fan Relay)
E-CVVT140A [G4KL] RLY. 8 (E-CVVT Relay)
TRAILER40A Trailer Connector
FUEL HEATER40A Diesel Junction Block (RLY.1 (Fuel Filter Heater Relay))
PTC HEATER130A Diesel Junction Block (RLY.2 (PTC Heater #1 Relay))
PTC HEATER230A Diesel Junction Block (RLY.3 (PTC Heater #2 Relay))
PTC HEATER330A Diesel Junction Block (RLY.4 (PTC Heater #3 Relay))

09
9-55
Engine compartment fuse panel
Fuse NameFuse Rating Circuit Protected
ESC310A ESP Control Module
ECU310A ECM
ECU215A ECM
HORN20A Horn Relay
WIPER130A Wiper Power Relay
TCU215A P/N Relay, TCM
SENSOR410AElectronic Oil Pump Module, Brake Vacuum Switch, E/R
Junction Block (RLY.1 (Brake Vacuum Relay))
TCU120A TCM
WIPER210A IBU, ECM
SENSOR115ARear Sub Junction Block (Fuel Pump Relay),
[D4HB] Rail Pressure Regulating Valve, DieseL Junction
Block (RLY.1 (Fuel Filter Heater Relay))
SENSOR520A[G4KL] Ignition Coil #1/#2/#3/#4
[G6DP] Ignition Coil #1/#2/#3/#4/#5/#6
[D4HB] Electronic Water Pump
MODULE10A Active Air Flap LH
ACTIVE HOOD10A Active Hood Lift Control Module
SENSOR110A[D4HB] Glow Relay Unit, Fuel Heater & Water Separator
Sensor
ECU120A ECM
SENSOR315A[G4KL] Oxygen Sensor (Up/Down)
[G6DP] Oxygen Sensor #1/#2/#3/#4
[D4HB] Lambda Sensor #1/#2, Electronic VGT Actuator,
Fuel Metering Unit, EGR Cooing Bypass Solenoid
Vlave, PTC Heater, Mid Nox Sensor, PM Sensor,
Rear Nox Sensor

09
9-61
Consult an authorized retailer of
Genesis Branded products to replace
most vehicle light bulbs. It is difficult
to replace vehicle light bulbs because
other parts of the vehicle must be
removed before you can get to the bulb.
This is especially true for removing the
headlamp assembly to get to the bulb(s).
Removing/installing the headlamp
assembly can result in damage to the
vehicle.
WARNING

[Prior to working on a light, depress
the foot brake, shift to P (Park), apply
the parking brake, press the Engine
Start/Stop button to the OFF position
and take the key with you when
leaving the vehicle to avoid sudden
movement of the vehicle and to
prevent possible electric shock.

[Be aware the bulbs may be hot and
may burn your fingers.
NOTICE
Be sure to replace the burned-out bulb
with one of the same wattage rating.
Otherwise, it may cause damage to the
fuse or electrical wiring system.
NOTICE
To prevent damage, do not clean the
headlamp lens with chemical solvents
or strong detergents.
Information
The headlamp and tail lamp lenses could
appear frosty if the vehicle is washed after
driving or the vehicle is driven at night in
wet weather. This condition is caused by
temperature difference between the lamp
inside and outside and, it does not indicate
a problem with your vehicle. When
moisture condenses in the lamp, it will be
removed after driving with the headlamp
on. The removable level may differ
depending on lamp size, lamp position
and environmental condition. However, if
moisture is not removed, have the vehicle
inspected by an authorized retailer of
Genesis Branded products.
Information

[A normally functioning lamp may
flicker momentarily to stabilize the
vehicle’s electrical control system.
However, if the lamp goes out after
flickering momentarily, or continues to
flicker, have the system checked by an
authorized retailer of Genesis Branded
products.

[The parking lamp may not turn on
when the parking lamp switch is turned
on, but the parking lamp and headlamp
switch may turn on when the headlamp
switch is turned on. This may be caused
by network failure or vehicle electrical
control system malfunction. If this
occurs, have the system checked by an
authorized retailer of Genesis Branded
products.
Information
The headlamp aiming should be adjusted
after an accident or after the headlamp
assembly is reinstalled at an authorized
retailer of Genesis Branded products.
LIGHT BULBS

09
9-67
NOTICE

[Do not use strong soap, chemical
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.

[Be careful when washing the side
windows of your vehicle.

[Especially, with high-pressure water,
water may leak through the windows
and wet the interior.

[To prevent damage to the plastic
parts, do not clean with chemical
solvents or strong detergents.
NOTICE
OIK090045

[Water washing in the engine
compartment including high
pressure water washing may cause
the failure of electrical circuits
located in the engine compartment.

[Never allow water or other liquids
to come in contact with electrical/
electronic components inside the
vehicle as this may damage them.
NOTICE
Matte paint finish vehicle
Automatic car wash which uses rotating
brushes should not be used as this can
damage the surface of your vehicle. A
steam cleaner which washes the vehicle
surface at high temperature may cause
the oil to adhere and leave stains that is
difficult to remove.
Use a soft cloth (e.g. microfiber towel or
sponge) when washing your vehicle and
dry with a microfiber towel. When you
handwash your vehicle, you should not
use a cleaner that finishes with wax.
Waxing
A good coat of wax is a barrier between
your paint and contamination. Keeping
a good coat of wax on your vehicle will
help protect it.
Wax the vehicle until water will no longer
bead on the paint.
Always wash and dry the vehicle before
waxing. Use a good quality liquid or
paste wax, and follow the manufacturer’s
instructions. Wax all metal trim to protect
it and to maintain its luster.
Removing oil, tar, and similar materials
with a spot remover will usually strip the
wax from the finish. Be sure to re-wax
these areas even if the rest of the vehicle
does not yet need waxing.