2022 HYUNDAI ELANTRA sensor

08
8-11
If either telltale illuminates, immediately
reduce your speed, avoid hard cornering
and anticipate increased stopping
distances. You should stop and check
your tires as soon as possible. Inflate the
tires to the proper pressure as indicated
on the vehicle’s placard or tire inflation
pressure label located on the driver’s
side center pillar outer panel.
If you cannot reach a service station or
if the tire cannot hold the newly added
air, replace the low pressure tire with the
spare tire.
The Low Tire Pressure Telltale will remain
on and the TPMS Malfunction Indicator
may blink for one minute and then
remain illuminated (when the vehicle
is driven approximately 10 minutes at
speed above 15.5 mph (25km/h)) until
you have the low pressure tire repaired
and replaced on the vehicle.
Information
The spare tire is not equipped with a tire
pressure sensor.
CAUTION
In winter or cold weather, the Low Tire
Pressure Telltale may be illuminated if
the tire pressure was adjusted to the
recommended tire inflation pressure
in warm weather. It does not mean
your TPMS is malfunctioning because
the decreased temperature leads to a
proportional lowering of tire pressure.
When you drive your vehicle from a
warm area to a cold area or from a cold
area to a warm area, or the outside
temperature is greatly higher or lower,
you should check the tire inflation
pressure and adjust the tires to the
recommended tire inflation pressure.
WARNING
Low pressure damage
Significantly low tire pressure makes
the vehicle unstable and can contribute
to loss of vehicle control and increased
braking distances.
Continued driving on low pressure tires
can cause the tires to overheat and fail.

Emergency Situations
8-12
TPMS (Tire Pressure
Monitoring System)
malfunction indicator
The TPMS Malfunction Indicator
will illuminate after it blinks for
approximately one minute when there
is a problem with the Tire Pressure
Monitoring System.
We recommend that the system be
checked by an authorized HYUNDAI
dealer.
NOTICE
If there is a malfunction with the TPMS,
the Low Tire Pressure Position Telltale
will not be displayed even though the
vehicle has an under-inflated tire.
NOTICE
The TPMS Malfunction Indicator may
illuminate after blinking for one minute
if the vehicle is near electric power
supply cables or radio transmitters
such as police stations, government
and public offices, broadcasting
stations, military installations, airports,
transmitting towers, etc.
Additionally, the TPMS Malfunction
Indicator may illuminate if snow chains
are used or electronic devices such as
computers, chargers, remote starters,
navigation, etc. This may interfere with
normal operation of the TPMS.
Changing a tire with TPMS
If you have a flat tire, the Low Tire
Pressure and Position telltales will come
on. We recommend that the flat tire be
repaired by an authorized HYUNDAI
dealer as soon as possible or replace the
flat tire with the spare tire.
NOTICE
It is recommended that you do not use a
puncture-repairing agent not approved
by a HYUNDAI dealer to repair and/or
inflate a low pressure tire. Tire sealant
not approved by a HYUNDAI dealer may
damage the tire pressure sensor.
The spare tire (if equipped) does not
come with a tire pressure monitoring
sensor. When the low pressure tire or
the flat tire is replaced with the spare
tire, the Low Tire Pressure Telltale will
remain on. Also, the TPMS Malfunction
Indicator will illuminate after blinking
for one minute if the vehicle is driven
at speed above 15.5 mph (25km/h) for
approximately 10 minutes.
Once the original tire equipped with
a tire pressure monitoring sensor is
reinflated to the recommended pressure
and reinstalled on the vehicle, the
Low Tire Pressure Telltale and TPMS
Malfunction Indicator will go off within a
few minutes of driving.
If the indicators do not extinguish after a
few minutes, please visit an authorized
HYUNDAI dealer.

08
8-13
Each wheel is equipped with a tire
pressure sensor mounted inside the tire
behind the valve stem (except for the
spare tire). You must use TPMS specific
wheels. It is recommended that you
always have your tires serviced by an
authorized HYUNDAI dealer.
You may not be able to identify a tire
with low pressure by simply looking at it.
Always use a good quality tire pressure
gauge to measure the tire’s inflation
pressure. Please note that a tire that is
hot (from being driven) will have a higher
pressure measurement than a tire that is
cold.
A cold tire means the vehicle has been
sitting for 3 hours and driven for less
than 1 mile (1.6 km) in that 3 hour period.
Allow the tire to cool before measuring
the inflation pressure. Always be sure
the tire is cold before inflating to the
recommended pressure.
WARNING

[The TPMS cannot alert you to severe
and sudden tire damage caused by
external factors such as nails or road
debris.

[If you feel any vehicle instability,
immediately take your foot off
the accelerator, apply the brakes
gradually with light force, and slowly
move to a safe position off the road.
WARNING
Tampering with, modifying, or disabling
the Tire Pressure Monitoring System
(TPMS) components may interfere
with the system’s ability to warn the
driver of low tire pressure conditions
and/or TPMS malfunctions. Tampering
with, modifying, or disabling the Tire
Pressure Monitoring System (TPMS)
components may void the warranty for
that portion of the vehicle.
Information
This device complies with Part 15 of the
FCC rules.
Operation is subject to the following three
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any
interference received, including
interference that may cause undesired
operation.
3. Changes or modifications not expressly
approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.

08
8-21
WARNING
If your vehicle is equipped with a
rollover sensor, place the ignition
switch in the LOCK/OFF or ACC position
when the vehicle is being towed.
The side impact and curtain air bag
may deploy if the sensor detects the
situation as a rollover.
OCN7070095L
When towing your vehicle in an
emergency without wheel dollies:
1. Place the ignition switch in the ACC
position.
2. Place the shift button in N (Neutral).
3. Release the parking brake.
CAUTION
Failure to place the shift button in N
(Neutral) when being towed with the
front wheels on the ground can cause
internal damage to the transmission.
Emergency Towing
If towing is necessary, we recommend
you have it done by an authorized
HYUNDAI dealer or a commercial tow
truck service.
Removable towing hook
OCN7070013
1. Open the trunk, and remove the
towing hook from the tool case.
OCN7070014
2. Remove the hole cover by pressing
the lower part of the cover on the
bumper.
3. Install the towing hook by turning it
clockwise into the hole until it is fully
secured.
4. Remove the towing hook and install
the cover after use.

09
9-51
(QJLQHFRPSDUWPHQWIXVHSDQHO
Type Fuse NameFuse Rating Circuit Protected
FUSEPOWER
OUTLET220A
Front Power Outlet
POWER
OUTLET320A Not Used
COOLING
FAN140ACooling Fan (Smartstream G 2.0 Atkinson
only)
DCT140A [G4FP] TCM
DCT240A [G4FP] TCM
REAR
HEATED40A Rear glass heated
B+440AICU Junction Block (Fuse - AIR BAG2,
IBU1, BRAKE SWITCH, DOOR LOCK, IAU,
MODULE1, SUNROOF,Power Window Relay)
AMS10A Battery Sensor
TCU110A [DCT] TCM, [M/T] Ignition Lock
FUEL PUMP20AFuel Pump Control Module (T-GDI), Fuel
Pump Motor (NU MPI AKS)
CVVD40A [G4FP] CVVD Actuator
ABS140AABS Control Module, ESC Control Module,
Multipurpose Check Connector
ABS230AABS Control Module, ESC Control Module,
Multipurpose Check Connector
EOP130AElectronic Oil Pump (Smartstream G 2.0
Atkinson ISG only)
POWER
OUTLET140A P/OUTLET FRT
CN7 HMA 9.indd 9-512020-12-03 9:42:31

Maintenance
9-52
(QJLQHFRPSDUWPHQWIXVHSDQHO
Fuse NameFuse Rating Circuit Protected
WIPER25A Wiper Motor
ECU415A PCM/ECM
A/C10A[G4FM] A/C Compressor (Smartstream G 2.0 Atkinson
only)
HORN15A Horn
IGN COIL20A Ignition Coil #1~#4
ECU315A PCM/ECM
SENSOR310A E/R Junction Block (Fuel Pump Relay)
ECU210A PCM/ECM (Smartstream G1.6 T-GDi only)
SENSOR210A[G4NS] Variable Intake Solenoid Valve, Oil Pump
Solenoid Valve, Oil Control Valve #1/#2, Canister Close
Valve, Purge Control Solenoid Valve,
PCB Block (A/C Relay), E/R Junction Block (Cooling
Fan1/2 Relay)
[G4FP] Variable Oil Pump Solenoid, Oil Control Valve
#1/#2, Purge ControL Solenoid Valve, RCV Control
Solenoid Valve, CanisteR Close Valve
ECU510ACVVD Actuator (Smartstream G1.6 T-GDi only), ECM/
PCM, Ignition Lock
SENSOR115A Oxygen Sensor (UP/DOWN)
ABS310AABS Control Module, ESC Control Module, Multipurpose
Check Connector
INJECTOR15A[G4FM/G4FG/G4NA] Injector #1~#4 (Smartstream G 2.0
Atkinson only)
ECU120A PCM/ECM
TCU215ATransaxle Range Switch, [G4FP] TCM (Smartstream G1.6
T-GDi & DCT only)
CN7 HMA 9.indd 9-522020-12-03 9:42:31

Maintenance
9-62
APPEARANCE CARE
Exterior Care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
High-pressure washing
• When using high-pressure washers,
make sure to maintain sufficient
distance from the vehicle. Insufficient
clearance or excessive pressure can
lead to component damage or water
penetration.
• Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.
• Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
• Do not use any high-pressure nozzles,
which induce either one-direct water
stream or water swirling.
Protecting your vehicle’s finish
:DVKLQJ
To help protect your vehicle’s finish from
rust and de
terioration, wash it thoroughly
and frequently at least once a month
with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to the
removal of any accumulation of salt, dirt,
mud, and other foreign materials. Make
sure the drain holes in the lower edges
of the doors and rocker panels are kept
clear and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, should be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish.
+LJKSUHVVXUHZDVKLQJ
• When using high-pressure washers,
make sure to maintain sufficient
distance from the vehicle. Insufficient
clearance or excessive pressure can
lead to component damage or water
penetration.
• Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.
• Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
CN7 HMA 9.indd 9-622020-12-03 9:42:37

I
I-5
E
Emission Control System .................................................................................... 9-71
Engine Compartment ..................................................................................... 2-8/ 9-3
Engine Coolant .................................................................................................... 9-17
Changing Engine Coolant ................................................................................ 9-19
Checking the Engine Coolant Level................................................................. 9-17
Engine Number .................................................................................................... 2-16
Engine Oil ............................................................................................................ 9-15
Checking the Engine Oil and Filter .................................................................. 9-16
Checking the Engine Oil Level ........................................................................ 9-15
Engine specification............................................................................................... 2-9
Explanation of Scheduled Maintenance Items .................................................... 9-13
Dual clutch transmission fluid ......................................................................... 9-14
Exterior Lights ..................................................................................................... 5-68
Battery saver function ...................................................................................... 5-71
Headlamp delay function ................................................................................. 5-71
High beam operation ........................................................................................ 5-69
Lighting control ................................................................................................ 5-68
Turn signals and lane change signals ............................................................... 5-70
Exterior Overview ................................................................................................. 2-2
F
Forward Collision–Avoidance Assist (FCA) (front view camera only) ............... 7-2
Function malfunction and limitations ................................................................ 7-7
Function operation.............................................................................................. 7-5
Function settings ................................................................................................ 7-3
Forward Collision–Avoidance Assist (FCA) (sensor fusion) ............................. 7-14
Function malfunction and limitations .............................................................. 7-22
Function operation............................................................................................ 7-18
Function settings .............................................................................................. 7-16
Fuel filler door ..................................................................................................... 5-66
Fuel Requirements ................................................................................................. 1-5
Detergent Fuel Additives.................................................................................... 1-7
Gasoline containing alcohol or methanol ........................................................... 1-6
Gasoline containing MMT ................................................................................. 1-6
Operation in foreign countries............................................................................ 1-7
Using Fuel Additives (except Detergent Fuel Additives)................................... 1-6