2022 HYUNDAI ELANTRA N window

06
6-65
The severe weather conditions of winter
quickly wear out tires and cause other
problems. To minimize winter driving
problems, you should take the following
suggestions:
Snow or Icy Conditions
You need to keep sufficient distance
between your vehicle and the vehicle in
front of you.
Apply the brakes gently. Speeding, rapid
acceleration, sudden brake applications,
and sharp turns are potentially
very hazardous practices. During
deceleration, use engine braking to the
fullest extent. Sudden brake applications
on snowy or icy roads may cause the
vehicle to skid.
To drive your vehicle in deep snow, it
may be necessary to use snow tires or to
install tire chains on your tires.
Always carry emergency equipment.
Some of the items you may want to carry
include tire chains, tow straps or chains,
a flashlight, emergency flares, sand, a
shovel, jumper cables, a window scraper,
gloves, ground cloth, coveralls, a blanket,
etc.
Snow tires
WARNING
Snow tires should be equivalent in size
and type to the vehicle’s standard tires.
Otherwise, the safety and handling of
your vehicle may be adversely affected.
If you mount snow tires on your vehicle,
make sure to use radial tires of the same
size and load range as the original tires.
Mount snow tires on all four wheels
to balance your vehicle’s handling in
all weather conditions. The traction
provided by snow tires on dry roads
may not be as high as your vehicle's
original equipment tires. Check with
the tire dealer for maximum speed
recommendations.
Information
Do not install studded tires without
first checking local, state and municipal
regulations for possible restrictions against
their use.
WINTER DRIVING
CN7 N HMA 6.indd 6-652021-09-14  9:42:41

Driving Your Vehicle6-68
Use approved window washer anti-
freeze in system
To keep the water in the window washer
system from freezing, add an approved
window washer anti-freeze solution in
accordance with instructions on the
container.
Window washer anti-freeze is available
from an authorized HYUNDAI dealer
and most auto parts outlets. Do not
use engine coolant or other types of
antifreeze as these may damage the
paint finish.
Do not let your parking brake freeze
Under some conditions your parking
brake can freeze in the engaged position.
This is most likely to happen when
there is an accumulation of snow or
ice around or near the rear brakes or
if the brakes are wet. If there is a risk
the parking brake may freeze, apply
it only temporarily while you put the
gear selector lever in P and block the
rear wheels so the car cannot roll. Then
release the parking brake.
Do not let ice and snow accumulate
underneath
Under some conditions, snow and ice
can build up under the fenders and
interfere with the steering. When driving
in severe winter conditions where this
may happen, you should periodically
check underneath the car to be sure the
movement of the front wheels and the
steering components is not obstructed.
Don't place foreign objects
or materials in the engine
compartment
Placement of foreign object or materials
which prevent cooling of the engine, in
the engine compartment, may cause a
failure or combustion. The manufacturer
is not responsible for the damage caused
by such placement.
To keep locks from freezing
To keep the locks from freezing, squirt
an approved de-icer fluid or glycerine
into the key opening. If a lock is covered
with ice, squirt it with an approved de-
icing fluid to remove the ice. If the lock
is frozen internally, you may be able to
thaw it out by using a heated key. Handle
the heated key with care to avoid injury.
CN7 N HMA 6.indd 6-68 2021-09-14  9:42:42

Maintenance9-28
Blade Inspection
Contamination of either the windshield
or the wiper blades with foreign matter
can reduce the effectiveness of the
windshield wipers.
Common sources of contamination are
insects, tree sap, and hot wax treatments
used by some commercial car washes. If
the blades are not wiping properly, clean
both the window and the blades with a
good cleaner or mild detergent, and rinse
thoroughly with clean water.
NOTICE
To prevent damage to the wiper blades,
arms or other components, do not:
• Use gasoline, kerosene, paint
thinner, or other solvents on or near
them.
• Attempt to move the wipers
manually.
• Use non-specified wiper blades.
Information
Commercial hot waxes applied by
automatic car washes have been known to
make the windshield difficult to clean.
Information
Wiper blades are consumable items.
Normal wear of the wipers may not be
covered by your vehicle warranty.
Blade Replacement
When the wipers no longer clean
adequately, the blades may be worn or
cracked, and require replacement.
NOTICE
• In order to prevent damage to the
hood and the wiper arms, the wiper
arms should only be lifted when in
the top wiping position.
• Always return the wiper arms to the
windshield before driving.
NOTICE
The use of a non-specified wiper blade
could result in wiper malfunction and
failure.
WIPER BLADES
CN7 N HMA 9.indd 9-28 2021-09-08  9:30:21

Maintenance9-32
Battery Recharging
WARNING
Always follow these instructions when
recharging your vehicle’s battery to
avoid the risk of SERIOUS INJURY or
DEATH from explosions or acid burns:
• Before performing maintenance or
recharging the battery, turn off all
accessories and place the ignition
switch to the LOCK/OFF position.
• Keep all flames, sparks, or smoking
materials away from the battery.
• Always work outdoors or in an area
with plenty of ventilation.
• Wear eye protection when checking
the battery during charging.
• The battery must be removed from
the vehicle and placed in a well
ventilated area.
• Watch the battery during charging,
and stop or reduce the charging
rate if the battery cells begin boiling
violently.
• Vehicle is equipped with the
Absorbent Glass Mat (AGM) battery.
Do not charge the AGM battery with
a general charger. It may damage
or explode the AGM battery. Only
charge the AGM battery with a
charger that has AGM battery
setting.
• The negative battery cable must
be removed first and installed last
when the battery is disconnected.
Disconnect the battery charger in the
following order:
1. Turn off the battery charger main
switch.
2. Unhook the negative clamp from the negative battery terminal.
3. Unhook the positive clamp from the positive battery terminal.
• Always use a genuine HYUNDAI
approved battery when you replace
the battery.
NOTICE
AGM battery (if equipped)
• Absorbent Glass Matt (AGM)
batteries are maintenance-free and
have the AGM battery be serviced
by an authorized HYUNDAI dealer.
For charging your AGM battery, use
only fully automatic battery chargers
that are specially developed for AGM
batteries.
• When replacing the AGM battery,
have you use parts for replacement
from an authorized HYUNDAI dealer.
• Do not open or remove the cap on
top of the battery. This may cause
leaks of internal electrolyte that
could result in severe injury.
By jump starting
After a jump start from a good battery,
drive the vehicle for 20-30 minutes
before it is shutoff. The vehicle may
not restart if you shut it off before the
battery had a chance to adequately
recharge. See “Jump Starting” in chapter
7 for more information on jump starting
procedures.
Information
An inappropriately disposed
battery can be harmful to
the environment and human
health. Dispose of the battery
according to your local law(s) or
regulations.
Reset Items
Items should be reset after the battery
has been discharged or the battery has
been disconnected.
• Auto up/down window (See chapter 5)
• Sunroof (See chapter 5)
• Trip computer (See chapter 4)
• Climate control system (See chapter 5)
CN7 N HMA 9.indd 9-32 2021-09-08  9:30:22

09
9-51
Driver’s side fuse panel
Fuse NameFuse Rating Circuit Protected
MEMORY1 10
ADriver/Passenger Power Outside Mirror, Instrument
Cluster, A/C Controller, A/C Control Module
AIR BAG2 10A SRS Control Module
MODULE4 10AFront View Camera, Crash Pad Switch, IBU, Front Console
Switch, E-LSD Controller, ECS Controller
MODULE7 7.5A Rear Seat Warmer Control Module, IAU
START 7.5A PCM/ECM IBU, E/R Junction Block(RLY.5)
CLUSTER 7.5A Instrument Cluster
IBU2 7.5A IBU
A/C1 7.5AE/R Junction Block(RLY.13), A/C Control Module, A/C
Controller, PTC HEATER RLY
TRUNK 10A Trunk Lid Latch
S/HEATER FRT 20AFront Air Ventilation Seat Control Module, Front Seat
Warmer Control Module
P/WINDOW LH 25A
Power Window Main Switch, Passenger Power Window
Switch
MULTIMEDIA 15A Audio, A/V & Navigation Head Unit
CN7 N HMA 9.indd 9-51
2021-09-08  9:30:27

Maintenance9-52
Driver’s side fuse panel
Fuse Name Fuse Rating Circuit Protected
MDPS1 7
.5A MDPS Unit
MODULE6 7.5A IBU
S/HEATER RR 20A Rear Seat Warmer Control Module
SAFETY P/
WINDOW DRV 25A Driver Safety Power Window Module
P/WINDOW RH 25A
Power Window Main Switch, Passenger Power Window
Switch
BRAKE
SWITCH 10A Stop Lamp Switch, IBU
IBU1 15A IBU
MODULE2 10AE/R Junction Block(RLY.2), Power Outside Mirror Switch,
AMP, IBU, Audio, A/V & Navigation Head Unit, IAU
AIR BAG1 15A SRS Control Module, ODS(Occupant Detection System)
MODULE5 10AFront Wirelesscharger, Crash Pad Switch, Electro Chromic
Mirror, A/C Controller, A/C Control Module, Audio, A/V &
Navigation Head Unit, Data Link Connector, AMP, Rear
Seat Warmer Control Module, Front Air Ventilation Seat
Control Module, Front Seat Warmer Control Module, Head
Lamp Leveling Device LH/RH, TGS Indicator
AMP 25A AMP
HEATED
MIRROR 10A
Driver/Passenger Power Outside Mirror, A/C Control
Module, A/C Controller
CN7 N HMA 9.indd 9-52
2021-09-08  9:30:27

Maintenance9-56
Engine compartment fuse panel
Type Fuse Name Fuse Rating Circuit Protected
FUSE POWER
OUTLET2 20
A Front Power Outlet
POWER
OUTLET3 20A Cigarette Lighter
VACUUM PUMP1 20A VACUUM PUMP, ESC
VACUUM PUMP2 10A Electronic Vacuum Pump
ECS 15A ECS Unit
E-LSD 20A LSD Control Module
E-CVVT3 20A ECM
E-CVVT2 20A ECM
E-CVVT1 40A E/R Junction Block (RLY.14)
DCT2 10A [G4FP] TCM
B+4 40AICU Junction Block (Fuse - F2, F25, F26, F34,
F43, F35 (IAU), F44, Power Window Relay)
AMS 10A Battery Sensor
TCU1 10A [M/T] Ignition Lock & Clutch Switch
FUEL PUMP 20A FUEL PUMP Motor
ABS1 40A ABS Control Module, ESP Control Module
ABS2 30AABS Control Module, ESP Control Module,
Multipurpose Check Connector
POWER
OUTLET1 40A E/R Junction Block (RLY.2)
WIPER 25A Wiper Motor
CN7 N HMA 9.indd 9-56
2021-09-08  9:30:27

Maintenance9-66
High-pressure washing
• When using high-pressure washers, mak
e sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors or its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.
• Do not bring the nozzle tip close to boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by water
before getting on the road. If braking
performance is impaired, dry the
brakes by applying them lightly while
maintaining a slow forward speed.
NOTICE
• Do not use strong soap, chemical
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.
• Be careful when washing the side
windows of your vehicle.
• Especially, with high-pressure water,
water may leak through the windows
and wet the interior.
• To prevent damage to the plastic
parts, do not clean with chemical
solvents or strong detergents.
NOTICE
OCN7N091016NOCN7N091016N
• Water washing in the engine
compartment including high
pressure water washing may cause
the failure of electrical circuits
located in the engine compartment.
• Never allow water or other liquids
to come in contact with electrical/
electronic components inside the
vehicle as this may damage them.
NOTICE
Matte paint finish vehicle (if equipped)
Automatic car wash which uses rotating
brushes should not be used as this can
damage the surface of your vehicle. A
steam cleaner which washes the vehicle
surface at high temperature may result
the oil to adhere and leave stains that is
difficult to remove.
Use a soft cloth (for example, microfiber
towel or sponge) when washing your
vehicle and dry with a microfiber towel.
When you hand wash your vehicle, you
should not use a cleaner that finishes
with wax. If the vehicle surface is too
dirty (sand, dirt, dust, contaminant,
etc.), clean the surface with water
before washing the car.
CN7 N HMA 9.indd 9-66 2021-09-08  9:30:32