2022 HONDA CIVIC display

140
uuGauges and Driver Information Interface uDriver Information Interface (Right Side Area)
Instrument Panel
Press the right selector wheel to switch between trip meter A and trip meter B.
■Trip meter
Shows the total number of miles or kilomete rs driven since the last reset. Meters A
and B can be used to measure two separate trips.
Resetting a trip meter
To reset the trip meter, display it, press and hold the right selector wheel and then
select Reset.
u The trip meter is reset to 0.0.
■Range / Fuel / Trip Meter
Trip Meter A Range
Average Fuel Economy
Instant Fuel
Economy Trip Meter B

Continued141
uuGauges and Driver Information Interface uDriver Information Interface (Right Side Area)
Instrument Panel
■Average fuel economy
Shows the estimated average fuel economy of each trip meter in mpg or l/100 km.
The display is updated at set intervals. Wh en a trip meter is reset, the average fuel
economy is also reset.
■Instant fuel economy
Shows the instant fuel economy as a bar graph in mpg or l/100 km.
■Range
Shows the estimated distance you can trave l on the remaining fuel. This estimated
distance is based on the vehicle’s current fuel economy.
1 Average fuel economy
You can change when to reset the average fuel
economy.
2 Customized Features P. 363
1Range
The driving range displayed is only an estimate and
may differ to the actual distance the vehicle can
travel.

Continued143
uuGauges and Driver Information Interface uDriver Information Interface (Right Side Area)
Instrument Panel
■Trip meter
2 Trip meter P. 140
■Elapsed time
Shows the time elapsed since Trip A or Trip B was reset.
■Average speed
Shows the average speed in mph or km/h since Trip A or Trip B was reset.
■Compass
Shows the compass screen.
■Turn-by-Turn Directions
When driving guidance is provided by the navigation system, Apple CarPlay or
Android Auto, turn-by-turn directions to your destination appear.
2 Refer to the Navigation System Manual
2 Apple CarPlay P. 319
2 Android Auto P. 258
■Navigation
1Elapsed time
You can change when to reset the elapsed time.
2 Customized Features P. 363
1Average speed
You can change when to reset the average speed.
2 Customized Features P. 363
1Navigation
When the compass or turn-by-turn directions are
displayed, you can contro l some navigation system
functions on the driver information interface by
pressing the right selector wheel.
2 Refer to the Navigation System Manual
You can select whether to have the turn-by-turn
display come on or not dur ing the route guidance.
2 Customized Features P. 363
Turn-by-turn directions may not be available for all
apps.

uuGauges and Driver Information Interface uDriver Information Interface (Right Side Area)
144
Instrument Panel
The Driver Attention Monitor analyzes steer ing inputs to determine if the vehicle is
being driven in a manner consistent with drowsy or inattentive driving. If it
determines that the vehicle is being driven in such a manner, it will display the
degree of the driver’s attention on the driver information interface.
When you select Driver Attention Monitor on
the driver information interface, bars on it
light up in white to indicate the degree of the
driver’s attention.
2 Switching the Display P. 139
■Driver Attention Monitor1Driver Attention Monitor
The Driver Attenti on Monitor cannot always detect if
the driver is tired or inattentive.
Regardless of the system’s feedback, if you are
feeling tired, stop in a safe location and rest for as
long as needed.
Driver Information Interface
Right Selector
Wheel
Level

uuGauges and Driver Information Interface uDriver Information Interface (Right Side Area)
148
Instrument Panel
Indicates the state of the Road Departure Mitigation system, CMBSTM, Low Speed
Braking Control and blind spot information system such as On, Off, or Failure, by
color and letters.
The following colors indica te the state of any of the above mentioned systems:
• Green: The system is on.
• Gray: The system is off.
• Amber: There is a probl em with the system.
■Safety Support1Safety Support
If a system is indicated by the color amber, have your
vehicle checked by a dealer immediately.
To turn on or off each system, first press the right
selector wheel to switch displays. From the next
display you can select which system to turn on or off. 2 Road Departure Mitigation system On and
Off P. 540
2 Blind Spot Information System On and Off
P. 471
2 System On and Off P. 491
2 CMBS
TM On and Off P. 480
You can also confirm the st ate of the each function
by the color of the sa fety support indicator.
2 Safety Support Indicator (Amber) P. 106
2 Safety Support Indicator (Green/Gray)
P. 108
Even when the Low Speed Braking Control icon is
green, if the parking sensor is turned off for the rear
only, the brake assist will not operate when reversing.
2 Turning off All Rear Sensors P. 568

uuGauges and Driver Information Interface uDriver Information Interface (Right Side Area)
150
Instrument Panel
You can check if there are any active warning messages.
Enables you to show another unit on the
driver information interface and set the
displayed measurements to read in either
miles and km, mph and km/h.
Press and hold the right selector wheel when
you select the Blank/Un it change screen on
the driver information interface. Each time you
do this, the unit will change from miles and
mph to km and km/h or vice versa. After this,
a confirmation screen will appear for a few
seconds.
■Warnings
■Speed/Distance Units
1 Warnings
If there are multiple warnings, you can roll the right
selector wheel to see other warnings.

Continued151
uuGauges and Driver Information Interface uDriver Information Interface (Right Side Area)
Instrument Panel
Change the settings to your liking.
■Arrange content on the right side area
You can choose which contents to display on the right side area. 1.Press the right selector wheel when you
select the Customize display on the driver
information interface.
2. Roll the right selector wheel to scroll to
select Hide/show , then press the right
selector wheel.
3. Roll the right selector wheel to scroll
between contents, then press the right
selector wheel to check or uncheck them.
■Customize Display1Arrange content on the right side area
Contents that are gray ca nnot be removed from the
right side area.
When you customize settings, shift to
( P.

uuGauges and Driver Information Interface uDriver Information Interface (Right Side Area)
152
Instrument Panel
■Change gauge design
You can change the design, such as speedometer, tachometer and so on. 1.Press the right selector wheel when you
select the Customize display on the driver
information interface.
2. Roll the right selector wheel to scroll to
select Gauge design , then press the right
selector wheel.
3. Roll the right selector wheel to scroll to
select your desired settings, then press the
right selector wheel.1Change gauge design
You can select the following design.
Round: Shows the speedometer and tachometer for
round type.
Bar: Shows the speedometer and tachometer for bar
type.
Round minimal: Shows the speedometer and
tachometer for round type while ACC with Low
Speed Follow is not in operation.
Bar minimal: Shows the speedometer and
tachometer for bar type while ACC with Low Speed
Follow is not in operation.