2022 CITROEN DS7 CROSSBACK check oil

163
Practical information07
appropriate for the temperature conditions
must be used in order to protect the system's
components (pump, tank, ducts, jets).
Filling with pure water is prohibited in all
circumstances (risk of freezing, limescale,
etc.).
Diesel fuel additive (Diesel with
particle filter)
On reaching the minimum level in the
particle filter additive tank, this warning
lamp comes on fixed, accompanied by an audible
signal and a warning message.
Topping up
The topping up of this additive must be carried
out quickly.
Visit a dealer or a qualified workshop.
AdBlue® (BlueHDi)
An alert is triggered when the reserve level is
reached.
For more information on the Indicators and in
particular the AdBlue range indicators, refer to
the corresponding section.
To avoid the vehicle being immobilised in
accordance with regulations, you must top up the
AdBlue tank.
For more information on AdBlue
® (BlueHDi), and
in particular the supply of AdBlue, refer to the
corresponding section.
Checks
Unless otherwise indicated, check these
components in accordance with the
Manufacturer's service schedule and according to
your engine.
Otherwise, have them checked by a dealer or a
qualified workshop.
Only use products recommended by the
Manufacturer or products of equivalent
quality and specification.
In order to optimise the operation of
components as important as those in the
braking system, the Manufacturer selects and
offers very specific products.
12 V battery
The battery does not require any
maintenance.
Check regularly that the terminals are correctly
tightened (versions without quick-release
terminals) and that the connections are clean.
For more information on the precautions
to take before any work on the 12 V
battery, refer to the corresponding section.
Versions equipped with Stop & Start are
fitted with a 12 V lead-acid battery with
special technology and specifications.
Its replacement should be carried out only by a
dealer or a qualified workshop.
Passenger compartment filter
Depending on the environment and the use
of the vehicle (e.g. dusty atmosphere, city
driving), change it twice as often, if necessary.
A clogged passenger compartment filter
can adversely affect air conditioning
system performance and generate undesirable
odours.
Air filter
Depending on the environment and the use
of the vehicle (e.g. dusty atmosphere, city
driving), change it twice as often, if necessary.
Oil filter
Change the oil filter each time the engine
oil is changed.
Particle filter (Diesel)
The start of clogging of the particle filter is
indicated by the temporary lighting of this
warning lamp, accompanied by an alert message.
As soon as traffic conditions allow, regenerate
the filter by driving at a speed of at least 37 mph
(60 km/h), with an engine speed above 2,500
rpm, for about 15 minutes (until the warning lamp
goes out).
If it is not possible to reach 37 mph (60 km/h),
leave the engine running at idle for about 15
minutes, then drive with an engine speed above
2,500 rpm for 15 minutes.

164
Practical information07
Do not switch off the engine until the filter
is fully regenerated; repeated intervals
can degrade the engine oil prematurely.
Regenerating the filter while the vehicle is
stationary is not recommended.
Following prolonged operation of the
vehicle at very low speed or at idle, you
may, in exceptional circumstances, notice
water vapour coming from the exhaust while
accelerating. These emissions have no impact
on the vehicle’s behaviour and the
environment.
New vehicle
During the first few particle filter
regeneration operations, you may notice a
"burning" smell. This is perfectly normal.
Automatic gearbox
The gearbox does not require any
maintenance (no oil change).
Electric parking brake
This system does not require any routine
servicing. However, in the event of a
problem, do not hesitate to have the system
checked by a dealer or a qualified workshop.
For more information on the Electric
parking brake, refer to the corresponding
section.
Brake pads
Brake wear depends on the style of driving,
particularly in the case of vehicles used in
town, over short distances. It may be necessary to
have the condition of the brakes checked, even
between vehicle services.
Unless there is a leak in the circuit, a drop in the
brake fluid level indicates that the brake pads are
worn.
After washing the vehicle, moisture, or in
wintry conditions, ice can form on the
brake discs and pads: braking efficiency may
be reduced. Gently dab the brakes to dry and
defrost them.
Brake disc wear
For information on checking brake disc
wear, contact a dealer or a qualified
workshop.
Wheels and tyres
The inflation pressure of all tyres,
including the spare wheel, must be
checked on "cold” tyres.
The pressures indicated on the tyre pressure label
are valid for "cold" tyres. If you have driven for
more than 10 minutes or more than 6 miles (10
kilometres) at over 31 mph (50 km/h), add 0.3 bar
(30 kPa) to the values indicated on the label.
Under-inflation increases energy
consumption. Non-compliant tyre
pressures cause tyres to wear prematurely and
have an adverse effect on the vehicle's road
holding - risk of accident!
Driving with worn or damaged tyres reduces the
braking and road holding performance of the
vehicle. Regularly check the condition of the tyres
(tread and sidewalls) and rims as well as the
presence of the valve caps.
When the wear indicators no longer appear set
back from the tread, the depth of the grooves is
less than 1.6 mm; replace the tyres as soon as
possible.
Using different size wheels and tyres from those
specified can affect the lifetime of tyres, wheel
rotation, ground clearance, the speedometer
reading and have an adverse effect on road
holding.
Fitting different tyres on the front and rear axles
can cause the ESC to mistime.
Always mark the direction of rotation on the tyres
that will be stored when fitting winter or summer
tyres. Store them in a cool, dry place and away
from direct exposure to the sun's rays.
Winter or 4-seasons tyres can be identified
by this symbol on their sidewalls.
Shock absorbers
It is not easy for drivers to detect when
shock absorbers are worn. Nevertheless,

173In the event of a breakdown08
power supply for long enough to repair a tyre
after a puncture.
Tyre inflation pressures are indicated on
this label.
For more information on Identification
markings, particularly this label, refer to the
corresponding section.
For more information on the Tool kit, refer
to the corresponding section.
Repair procedure
Do not remove any foreign body (e.g. nail,
screw) which has penetrated the tyre.
►  Park the vehicle without obstructing traffic
and apply the parking brake.
►  Follow the safety instructions (hazard warning
lamps, warning triangle, high visibility jacket,
etc.) according to the legislation in force in the
country in which you are driving.
►  Switch the ignition off.


► Remove the transparent cap from the bottle
of sealant.
►  Lift the protective cover before installing the
bottle of sealant on the compressor.
►  Turn the bottle of sealant over and screw it a
quarter turn into the compressor.
►  Remove the valve cap from the tyre to be
repaired, and place it in a clean place.


►  Uncoil the pipe stowed under the compressor.
►  Connect the pipe from the compressor to the
valve of the tyre to be repaired and tighten firmly.
►  Check that the compressor switch is in
position "O".
►  Fully uncoil the electric cable stowed under
the compressor.
►  Connect the compressor's electric plug to the
vehicle's 12 V socket.
►  Affix the speed limit sticker.
The speed limit sticker must be affixed
inside the vehicle in the area close to the
driver, to remind them that a wheel is in
temporary use.
►  Switch the ignition on.


► Switch on the compressor by moving the
switch to position "I" until the tyre pressure
reaches 2 bar. The sealant product is injected
under pressure into the tyre; do not disconnect
the pipe from the valve during this operation (risk
of blowback).
If after approximately 7 minutes, the
pressure of 2 bar is not reached, this
indicates that the tyre is not repairable;
contact a dealer or a qualified workshop for
assistance.

174In the event of a breakdown08
► Move the switch to position "O".
►  Disconnect the compressor's electric plug
from the vehicle's 12 V socket.
►  Remove the kit.
►  Refit the cap on the valve.
►  Remove and store the bottle of sealant.
The sealant product is harmful if
swallowed and causes irritation to the
eyes.
Keep this product out of the reach of children.
The use-by date of the fluid is marked on the
bottle.
After use, do not discard the bottle into
the environment; take it to a dealer or an
authorised waste disposal site.
Do not forget to obtain a new bottle of
sealant, available from a dealer or a qualified
workshop.


►  Drive immediately for approximately 3 miles
(5 kilometres) at reduced speed (between 12 and
37 mph (20 and 60 km/h)) to plug the puncture.
►  Stop to check the repair and the tyre pressure
using the kit:
• If the tyre pre ssure is incorrect, contact a
dealer to have the tyre changed.
•

If the tyre pre
ssure is correct, drive a second
time for approximately 3 miles (5 kilometres)
at reduced speed (between 12 and 37 mph (20
and 60 km/h)), stop then check again the tyre
pressure using the kit to confirm the effective
repair of the tyre.
With a tyre repaired using this type of kit,
do not exceed a speed of 50 mph
(80 km/h) and do not drive more than
125 miles (200 km).
You must contact a dealer or a qualified
workshop to have the repair checked and the
tyre changed.
Checking/adjusting tyre
pressures
The compressor can be used, without injecting
sealant, to check and, if necessary, adjust the
tyre pressures.
►  Remove the valve cap from the tyre and keep it
in a clean place.
►  Uncoil the pipe stowed under the compressor.
►  Screw the pipe onto the valve and tighten
firmly.
►  Check that the compressor switch is in
position "O".
►  Fully uncoil the electric cable stowed under
the compressor.
►  Connect the compressor's electric plug to the
vehicle's 12 V socket.
►  Switch the ignition on.
►  Start the compressor by placing the switch
at position "I" and adjust the pressure to the
value shown on the vehicle's tyre pressure label.
To deflate: press the black button located on the
compressor pipe, near the valve connection.
If after 7 minutes the pressure of 2 bar is
not reached, the tyre is damaged; contact
a dealer or a qualified workshop for
assistance.
►  Once the correct pressure is reached, put the
switch in position "O".
►  Remove the kit and stow it.
►  Refit the cap on the valve.
Should the pressure of one or more tyres
be adjusted, it is necessary to reinitialise
the under-inflation detection system.
For more information on Tyre under-inflation
detection, refer to the corresponding section.

214Alphabetical index
Charging connector
(Rechargeable hybrid)
146, 153–154
Charging flap
(Rechargeable hybrid)

146, 153–154
Charging the traction battery
(Rechargeable hybrid)

20, 145, 153–154
CHECK

21
Checking the engine oil level

18
Checking the levels

161–162
Checking tyre pressures (using the kit)

172, 174
Checks

161, 163–165
Checks, routine

163–164
Child lock

95
Children

83, 89–91, 94
Children (safety)

95
Child seats

83, 86–89
Child seats, conventional

88–89
Child seats, i-Size

94
Child seats, ISOFIX

90–92
Cigar lighter

56
Cleaning (advice)

146, 167–169
Clock

23
Closing the boot

29, 33
Closing the doors

29, 32
Collision Risk Alert

128–129
Comfort mode

108
Configuration, vehicle

10, 24
Connection, Bluetooth

202
Connectivity

207
Consumptions

24
Container, AdBlue®

165–166
Control, emergency boot release

33Control, emergency door 30–31
Control, heated seats
46
Controls, steering mounted

101–103
Control stalk, lighting

63–64
Control stalk, wipers

72–74
Control unit

147–149, 154
Courtesy lamp, front

59
Courtesy lamps

59
Cruise control

116, 118–120
Cruise control, adaptive

120
Cruise control, adaptive with Stop function

116
Cruise control by speed limit recognition

116
Cup holder

56
D
Date (setting) 208
Daytime running lamps
64, 179
Deactivating the passenger airbag

84, 87–88
Deadlocking

27, 29
Deferred charging

24, 155
Deferred charging
(Rechargeable hybrid)

24–25, 146, 153
Defrosting

47, 53
Defrosting, front

53
Defrosting, rear screen

54
Demisting

47, 53
Demisting, front

53
Demisting, rear

54
Diagnosis, vehicle

21
Dials and gauges 10
Digital instrument panel
10
Dimensions

193
Dipstick

18, 161
Direction indicators (turn signals)

64, 179
Display screen, instrument panel

10
Domestic charging

149
Domestic charging (Rechargeable hybrid)

154
Door pockets

56
Doors

32
Driver’s attention warning

131–132
Driving

42–43, 96–97
Driving aids camera (warnings)

112
Driving aid shortcuts

113
Driving aids (recommendations)

112
Driving economically

8
Driving modes

106
Driving positions (storing)

45
DS Drive Assist

120
Dynamic stability control (DSC)

80
E
EBFD 79
Eco-driving (advice)
8
ECO mode

106
Electric automatic gearbox
(Rechargeable hybrid)

104
Electronic brake force distribution (EBFD)

79
Emergency braking assistance (EBA)

80

216Alphabetical index
Indicator, AdBlue® range 19
Indicator, coolant temperature
19
Indicator, engine oil level

18
Indicators, direction

64
Indicator, service

17
Inflating tyres

164, 193
Inflating tyres and accessories
(using the kit)

172, 174
Information, vehicle

10, 210
Infrared camera

70, 112
Instrument panel

10, 22, 113
ISOFIX mountings

90
J
Jack 171–172, 175
Jump starting
181
K
Key 26–27, 30–31
Key, electronic
28–29
Keyless Entry and Starting

26, 28–29, 97–98
Key not recognised

99
Key with remote control

26, 97
Kit, hands-free

202
Kit, puncture repair

171–172
Kit, temporary puncture repair

171–174
Klaxon

77
L
Labels, identification 193
Lamps, parking
64
Lamps, rear

179
Lane assist

120, 124–126
Lane keeping assist

133
Leather (care)

169
LEDs - Light-emitting diodes

64, 178–179
Level, AdBlue®

163
Level, brake fluid

162
Level, Diesel additive

163
Level, engine coolant

19, 162
Level, engine oil

18, 161
Levels and checks

161–162
Level, screenwash fluid

73, 162
Light-emitting diodes - LEDs

64, 178–179
Lighting, boot

62
Lighting dimmer

21
Lighting, directional

69
Lighting, exterior

63, 66
Lighting, guide-me home

65–66
Lighting, interior

59
Lighting, mood

59
Lighting, welcome

65–66
Loading

61, 157–158
Load reduction mode

159
Load space cover

60
Locating your vehicle

27
Locking

27, 29
Locking from the inside

30
Locking the doors 30
Log, alerts
21
Long objects, transporting

60
M
Mains socket (domestic network) 147–148
Maintenance (advice)
146, 167
Maintenance, routine

113, 163–165
Manoeuvring aids (recommendations)

112
Map reading lamps

59
Markings, identification

193
Massage function

46
Massage, multi-point

46
Mat

59, 113
Menu, shortcuts

24
Mirror, rear view

47
Mirrors, door

47, 54, 135
Mirror, vanity

56
Misfuel prevention

144
Mobile application

24–25, 54, 153, 155
Motor, electric

107, 145, 192
Motorised tailgate

33–34
Mountings, ISOFIX

90
N
Net, high load retaining 61
Night vision
70