2022 CITROEN DS3 CROSSBACK tyre pressure

151In the event of a breakdown08

► Connect the hose from the bottle of sealant
to the valve of the tyre to be repaired and tighten
firmly.
►  Check that the compressor switch is in
position "O".
►  Fully uncoil the electric cable stowed under
the compressor.
►  Connect the compressor's electric plug to the
vehicle's 12 V socket.
►  Affix the speed limit sticker.
The speed limit sticker must be secured to
the interior of the vehicle in the area close
to the driver, to remind the driver that a wheel
is in temporary use.
The tyre inflation pressures are given on
this label.


►  Switch on the ignition.

► Switch on the compressor by moving the
switch to position "I" until the tyre pressure
reaches 2 bar. The sealant product is injected
under pressure into the tyre; do not disconnect
the pipe from the valve during this operation (risk
of blowback).
If after approximately 7 minutes, the
pressure of 2 bar is not reached, this
indicates that the tyre is not repairable;
contact a dealer or a qualified workshop for
assistance.
►  Move the switch to position "O".
►  Disconnect the compressor's electric plug
from the vehicle's 12 V socket.
►  Refit the cap on the valve.
►  Remove the kit.
►  Remove and store the bottle of sealant.
The sealant product is harmful if
swallowed and causes irritation to the
eyes.
Keep this product out of the reach of children.
The use-by date of the fluid is marked on the
bottle.
After use, do not discard the bottle in standard
waste, take it to a dealer or an authorised
waste disposal site.
Do not forget to obtain a new bottle of
sealant, available from a dealer or a qualified
workshop.


►  Drive immediately for approximately 3 miles
(5 kilometres) at reduced speed (between 12 and
37 mph (20 and 60 km/h)) to plug the puncture.
►  Stop to check the repair and the tyre pressure
using the kit.
With a tyre repaired using this type of kit,
do not exceed a speed of 50 mph
(80 km/h) and do not drive more than
125 miles (200 km).
Contact a dealer or a qualified workshop to
have the tyre changed.

152In the event of a breakdown08
Checking / adjusting tyre
pressures
The compressor can be used, without injecting
sealant, to check and, if necessary, adjust the
tyre pressures.
► Remove the valve cap from the tyre and keep it
in a clean place.
►  Uncoil the pipe stowed under the compressor.
►  Screw the pipe onto the valve and tighten
firmly.
►  Check that the compressor switch is in
position "O".
►  Fully uncoil the electric cable stowed under
the compressor.
►  Connect the compressor's electric plug to the
vehicle's 12 V socket.
►  Switch on the ignition.
The tyre inflation pressures are given on
this label.


► Start the compressor by placing the switch
at position "I" and adjust the pressure to the
value shown on the vehicle's tyre pressure label.
To deflate: press the black button located on the
compressor pipe, near the valve connection.
If after 7 minutes the pressure of 2 bar is
not reached, the tyre is damaged; contact
a dealer or a qualified workshop for
assistance.
►  Once the correct pressure is reached, put the
switch in position "O".
►  Remove the kit and stow it.
Should the pressure of one or more tyres
be adjusted, it is necessary to reinitialise
the under-inflation detection system.
For more information on Tyre under-inflation
detection, refer to the corresponding section.
Spare wheel
Scan the QR Code on page 3 to view
explanatory videos.
For more information on the Tool kit, refer
to the corresponding section.
Access to the spare wheel

The spare wheel is stored under the boot carpet.
The spare wheel is a ‘space-saver’ wheel.
Removing the spare wheel

►  Slacken the central nut.
►  Remove the fastening device (nut and bolt).
►  Lift the spare wheel towards you from the rear.
►  Take the wheel out of the boot.
Putting the spare wheel back in place
The punctured wheel cannot be placed in
the boot under the floor.


► Put the spare wheel back in place in its
housing.
►  Slacken the nut on the bolt by a few turns.
►  Position the fastening device (nut and bolt) in
the middle of the wheel.
►  Tighten the central nut sufficiently to retain
the wheel correctly.
►  Depending on version, put the tool box back
in place in the middle of the wheel and clip it in
place.
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
obstruct traffic: the ground must be level,
stable and non-slippery.
With a manual gearbox, engage first gear
to lock the wheels, apply the parking brake,
unless it is programmed to be in automatic
mode, and switch off the ignition.
With an automatic gearbox, select mode P
to lock the wheels, apply the parking brake,
unless it is programmed to be in automatic
mode, and switch off the ignition.

154In the event of a breakdown08
► Extend jack 6 until its head comes into contact
with jacking point A or B; contact area A or B on
the vehicle must be properly inserted into the
central part of the head of the jack.
►  Raise the vehicle until there is sufficient space
between the wheel and the ground to admit the
spare (not punctured) wheel easily.
Ensure that the jack is stable. If the
ground is slippery or loose, the jack may
slip or collapse - risk of injury!
Take care to position the jack strictly at
one of the jacking points A or B under the
vehicle, ensuring that the head of the jack is
centred under the contact area of the vehicle.
Otherwise, there is a risk of damage to the
vehicle and/or of the jack collapsing - risk of
injury!


►  Remove the bolts and store them in a clean
place.
►  Remove the wheel.
Fitting a wheel

Fitting a steel or "space-saver" type spare
wheel
If the vehicle is equipped with alloy wheels, the
washers do not make contact with the steel or
"space-saver" type spare wheel. The wheel is
secured by the conical contact of each bolt.


►  Fit the wheel on the hub.
►  Screw in the bolts by hand as far as possible.
►  Pre-tighten the security bolt using the
wheelbrace 5 equipped with a security socket 2.
►  Pre-tighten the other bolts using the
wheelbrace 5 only.


►  Lower the vehicle again fully.
►  Fold jack 6 and remove it.


► Tighten the security bolt using the
wheelbrace 5 equipped with a security socket 2.
►  Tighten the other bolts using the wheelbrace 5
only.
►  Refit the bolt covers to each of the bolts
(depending on equipment).
►  Store the tools.
After changing a wheel

With a "space-saver" type spare wheel
Deactivate certain driving aid functions
(Active Safety Brake, Adaptive cruise control,
etc.).
Do not exceed the maximum authorised speed
of 50 mph (80 km/h).
Driving with more than one “space-saver” type
spare wheel is prohibited.
Visit a dealer or a qualified workshop as
soon as possible to have the tightness of
the bolts and the pressure of the spare wheel
checked.
Have the punctured tyre examined. After
inspection, the technician will advise you on
whether the tyre can be repaired or if it must
be replaced.
Changing a bulb
In some weather conditions (e.g. low
temperature or humidity), the presence of
misting on the internal surface of the glass of
the headlamps and rear lamps is normal; it

155In the event of a breakdown08
After changing a wheel

With a "space-saver" type spare wheel
Deactivate certain driving aid functions
(Active Safety Brake, Adaptive cruise control,
etc.).
Do not exceed the maximum authorised speed
of 50 mph (80 km/h).
Driving with more than one “space-saver” type
spare wheel is prohibited.
Visit a dealer or a qualified workshop as
soon as possible to have the tightness of
the bolts and the pressure of the spare wheel
checked.
Have the punctured tyre examined. After
inspection, the technician will advise you on
whether the tyre can be repaired or if it must
be replaced.
Changing a bulb
In some weather conditions (e.g. low
temperature or humidity), the presence of
misting on the internal surface of the glass of
the headlamps and rear lamps is normal; it
disappears after the lamps have been on for a
few minutes.
The headlamps have polycarbonate
lenses with a protective coating:
–

Do not clean them with a dry or abrasiv
e
cloth, nor with detergent or solvent products.
–

U

se a sponge and soapy water or a pH
neutral product.
–

When using a high-pre
ssure washer on
persistent marks, do not keep the lance
directed towards the headlamps, lamps or
their edges for too long, so as not to damage
their protective coating and seals.
Changing a bulb must only be done with
the ignition off and after the headlamp /
lamp has been switched off for several
minutes - risk of serious burns!
Do not touch the bulb directly with your
fingers; use a lint-free cloth.
It is essential only to use anti-ultraviolet (UV)
type bulbs, so as not to damage the headlamp.
Always replace a failed bulb with a new bulb
of the same type and specification. To avoid
lighting imbalance, replace the bulbs in pairs.
After changing a bulb
To refit, carry out the operations in
reverse order to removal.
Close the protective cover very carefully to
guarantee the sealing of the lamps.
Light-emitting diode (LED)
headlamps and lamps
Depending on version, the affected types of
headlamps / lamps are:
–

"DS MA
TRIX LED VISION" headlamps.
–

Offset da
ytime running lamps.
–

Direction indic
ator side repeaters.
–

Side spo
tlamps.
–

Full LED t
echnology rear lamps.
–

Third brak
e lamp.
–

Number pla
te lamps.
For the replacement of this type of bulb,
you must contact a dealer or a qualified
workshop.
Do not touch the "Full LED" technology
headlamps - risk of electrocution!

220
Alphabetical index
A
ABS 66
Accessories
63
Active Safety Brake

115–117
AdBlue®

18, 144
AdBlue® tank

145
Additive, Diesel

143
Adjusting headlamps

56
Adjusting head restraints

39
Adjusting seat

38–39
Adjusting the air distribution

44, 46
Adjusting the air flow

44–45
Adjusting the date

193, 215
Adjusting the height and reach of
the steering wheel

40
Adjusting the lumbar support

39
Adjusting the seat angle

38
Adjusting the temperature

44–45
Adjusting the time

180, 193, 216
Advanced Traction Control

67
Advice on care and maintenance

131, 146
Advice on driving

7, 80–81
Airbags

70–72, 74
Airbags, curtain

71–72
Airbags, front

70–71, 74
Airbags, lateral

71–72
Air conditioning

43, 46
Air conditioning, automatic

45
Air conditioning, manual

44
Air intake

47
Air vents

43
Alarm

34–36
Amplifier, audio

50
Android Auto connection

207
Anti-lock braking system (ABS)

66
Antitheft / Immobiliser 31, 81
Apple CarPlay connection
189, 206
Applications

207
Armrest, front

49
Assistance call

64
Assistance, emergency braking

66, 116
Audible warning

64
Audio streaming (Bluetooth)

177–178, 187, 211
B
Battery 138
Battery, 12 V
142, 161–164
Battery, ancillaries

161–162
Battery, charging

130, 134, 163–164
Battery, remote control

32–33
Blind spot monitoring system, active

114
Blind spot sensors

113–114
BlueHDi

18, 142, 148
Bluetooth (hands-free)

178, 190, 212
Bluetooth (telephone)

178, 190, 212–213
Bodywork

147
Bonnet

139
Boot

34, 53
Brake discs

143
Brake lamps

157–158
Brakes

143
Braking

90
Braking assistance system

66
Braking, automatic emergency

115–117
Braking, dynamic emergency

84–85
Brightness

179, 192
Bulbs

156
Bulbs (changing)

155–158
C
Cable, audio 211
Cable, Jack
211
Capacity, fuel tank

129
Cap, fuel filler

129
Care of the bodywork

147
CD

177, 187
CD, MP3

177, 187
Central locking

30
Changing a bulb

155–158
Changing a fuse

159–161
Changing a wheel

149, 152
Changing a wiper blade

61
Changing the remote control battery

32
Charger, induction

50
Charger, wireless

50
CHECK

21
Checking the levels

140–142
Checking tyre pressures
(using the kit)

150, 152
Checks

140, 142–144
Checks, routine

142–143
Child lock

79
Children

69, 75–76
Children (safety)

79
Child seats

69, 72–74
Child seats, conventional

74
Child seats, i-Size

76
Child seats, ISOFIX

75–76
Cleaning (advice)

131, 146–147
Closing the boot

30, 34
Closing the doors

29–30, 33
Collision Risk Alert

115–116
Configuration, vehicle

24
Connected applications

207

223
Alphabetical index
Maintenance (advice) 131, 146
Maintenance, routine
95, 142
Manoeuvring aids (recommendations)

94
Map reading lamps

51–52
Markings, identification

172
Massage function

39–40
Mat

51, 95
Memorising a speed

102
Menu

189
Menu, main

24
Menus (audio)

174–175, 184–185, 196–197
Menu short cuts

24
Messages

214
Messages, quick

214
Mirror, rear view

41
Mirrors, door

41, 47, 113
Mirror, vanity

49
Misfuel prevention

130
Motor, electric

5, 82, 130, 171
Mountings, ISOFIX

75
N
Navigation 202–204
Navigation, connected
204–206
Net, high load retaining

53
O
Obstacle detection 117
Oil change
141
Oil consumption

141
OIl, engine

141
On-board tools 53, 148–150
Opening the bonnet
139
Opening the boot

29, 34
Opening the doors

29, 33–34
Opening the windows

27
P
Pads, brake 143
Paint
147, 172
Paint colour code

172
Parcel shelf, rear

53
Park Assist

121
Parking brake

143
Parking brake, electric

83–85
Parking sensors, audible and visual

117
Parking sensors, front

118
Parking sensors, rear

117
Personalisation

9–10
Plates, identification

172
Player, Apple®

177, 188
Player, Apple®

211
Player, USB

177, 187, 210
Port, USB

49, 177, 187, 206, 210
Power

19
Power indicator

19
Pressures, tyres

143, 152
Pre-tensioning seat belts

69
Priming the fuel system

148
Profiles

192, 215
Protecting children

70, 72–76
Puncture

150, 152
R
Radar (warnings) 94
Radio
175–176, 185, 187, 209
Radio, digital (Digital Audio
Broadcasting - DAB)

176, 187–188, 210
Range, AdBlue

18, 142
RDS

176, 186, 209
Rear screen, demisting

47
Recharging the battery

163–164
Recirculation, air

47
Recovery

165–167
Reduction of electrical load

139
Regeneration of the particle filter

143
Reinitialisation of the under-inflation
detection system

94
Reinitialising the remote control

33
Reminder, lighting on

54
Remote control

27, 29–31
Removing a wheel

153–154
Removing the mat

51
Replacing bulbs

155–158
Replacing fuses

159–161
Replacing the air filter

142
Replacing the oil filter

143
Replacing the passenger compartment
filter

142
Reservoir, screenwash

142
Reset trip

22
Rev counter

9
Reversing camera

95, 118–119
Reversing lamp

158
Roof bars

137–138
Running out of fuel (Diesel)

148