2022 CHRYSLER 300 homelink

3
UNIVERSAL GARAGE DOOR OPENER
(HOMELINK®) ....................................................... 40
Before You Begin Programming HomeLink® ... 40

Erasing All The HomeLink® Channels ............40
Identifying Whether You Have A Rolling Code
Or Non-Rolling Code Device.............................40
Programming HomeLink® To A Garage
Door Opener .....................................................41
Programming HomeLink® To A Miscellaneous
Device ...............................................................42

Reprogramming A Single HomeLink® Button .. 42

Canadian/Gate Operator Programming .........42
Security .............................................................43
Troubleshooting Tips ........................................43
EXTERIOR LIGHTS ................................................. 44
Headlight Switch...............................................44
Multifunction Lever ..........................................45
Daytime Running Lights (DRLs).......................45
High/Low Beam Switch....................................45
Automatic High Beam — If Equipped .............45
Flash-To-Pass....................................................46
Automatic Headlights ......................................46
Parking Lights ..................................................46
Headlights On With Wipers ..............................46 Adaptive Bi-Xenon High Intensity Discharge
Headlights — If Equipped .................................46
Headlight Time Delay ......................................46
Lights-On Reminder ........................................47
Fog Lights — If Equipped..................................47
Turn Signals .....................................................47
Lane Change Assist — If Equipped ..................47
Automatic Headlight Leveling —If Equipped ...48
INTERIOR LIGHTS ..................................................48
Interior Courtesy Lights ....................................48
WINDSHIELD WIPERS AND WASHERS............... 50
Windshield Wiper Operation ............................50
Rain Sensing Wipers — If Equipped ...............51
CLIMATE CONTROLS .............................................52
Automatic Climate Control Descriptions And
Functions ..........................................................52
Automatic Temperature Control (ATC) ...........54
Climate Voice Commands................................55
Operating Tips .................................................55
INTERIOR STORAGE AND EQUIPMENT ............... 56
Storage..............................................................56
USB/AUX Control ..............................................58
Lighted Cupholders — If Equipped ..................59
Power Sunshade — If Equipped ......................59
Power Outlets ...................................................60 WINDOWS ............................................................. 61
Power Window Controls ................................... 61
Automatic Window Features .......................... 62
Reset Auto-Up .................................................. 62
Window Lockout Switch ................................... 62
Wind Buffeting .................................................63
PANORAMIC SUNROOF — IF EQUIPPED ............. 63
Opening And Closing The Sunroof .................. 64
Pinch Protect Feature ...................................... 64
Opening And Closing The Power Shade..........64
Sunroof Maintenance ...................................... 65
Ignition Off Operation....................................... 65
HOOD....................................................................... 65
Opening The Hood ..........................................65
Closing The Hood ............................................. 65
TRUNK ..................................................................... 65
Opening The Trunk ........................................... 65
Closing The Trunk............................................. 66
Trunk Safety ..................................................... 66
Cargo Area Features ....................................... 67

22_LX_OM_EN_USC_t.book Page 3

40GETTING TO KNOW YOUR VEHICLE
UNIVERSAL GARAGE DOOR OPENER
(HOMELINK®)

HomeLink® Buttons And Indicator Light

Use this QR code to access your
digital experience.
HomeLink® replaces up to
three hand-held transmitters
that operate devices such as
garage door openers, motor -
ized gates, lighting, or home
security systems. The HomeLink® unit is
powered by your vehicle’s 12 Volt battery.
The HomeLink® buttons that are located in the
overhead console or sunvisor designate the
three different HomeLink® channels.
To operate HomeLink®, push and release any
of the programmed HomeLink® buttons. These
buttons will activate the devices they are
programmed to with each press of the corre -
sponding HomeLink® button.
The HomeLink® indicator light is located above
the center button.
NOTE:HomeLink® is disabled when the Vehicle Security
system is active Ú page 273.
BEFORE YOU BEGIN PROGRAMMING
H
OMELINK®
For efficient programming and accurate
transmission of the Radio Frequency (RF) signal, it
is recommended that a new battery be placed in
the hand-held transmitter of the device that is
being programmed to the HomeLink® system.
Make sure your hand-held transmitter is
programmed to activate the device you are trying
to program your HomeLink® button to.
Ensure that your vehicle is parked outside of the
garage before you begin programming.
It is recommended that you erase all the channels
of your HomeLink® before you use it for the first
time.
ERASING ALL THE HOMELINK®
C
HANNELS
To erase the channels, follow this procedure:

1. Place the ignition switch into the ON/RUN
position.

2. Push and hold the two outside HomeLink® buttons (I and III) for up to 20 seconds, or until
the HomeLink® indicator light flashes.
NOTE:Erasing all channels should only be performed
when programming HomeLink® for the first time.
Do not erase channels when programming addi -
tional buttons.
IDENTIFYING WHETHER YOU HAVE A
R
OLLING CODE OR NON-ROLLING CODE
D
EVICE
Before programming a device to one of your
HomeLink® buttons, you must determine whether
the device has a rolling code or non-rolling code.

22_LX_OM_EN_USC_t.book Page 40

GETTING TO KNOW YOUR VEHICLE41
Rolling Code Devices
To determine if your device has a rolling code, a
good indicator is its manufacturing date. Typically,
devices manufactured after 1995 have rolling
codes. A device with a rolling code will also have a
“LEARN” or “TRAIN” button located where the
antenna is attached to the device. The button may
not be immediately visible when looking at the
device. The name and color of the button may vary
slightly by manufacturer.
NOTE:The “LEARN” or “TRAIN” button is not the button
you normally use to operate the device.
Non-rolling Code Devices
Most devices manufactured before 1995 will not
have a rolling code. These devices will also not
have a “LEARN” or “TRAIN” button.
PROGRAMMING HOMELINK® TO A
G
ARAGE DOOR OPENER
To program any of the HomeLink® buttons to
activate your garage door opener motor, follow the
steps below:
NOTE:All HomeLink® buttons are programmed using this
procedure. You do not need to erase all channels
when programming additional buttons.
1. Place the ignition switch into the ON/RUN
position.

2. Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the
HomeLink® button you wish to program, while
keeping the HomeLink® indicator light in view.
3. Push and hold the HomeLink® button you want to program while you push and hold the
garage door opener transmitter button you are
trying to replicate.
4. Continue to hold both buttons and observe the HomeLink® indicator light. The HomeLink®
indicator light will flash slowly and then rapidly.
Once this happens, release both buttons.
NOTE:Make sure the garage door opener motor is
plugged in before moving on to the rolling code/
non-rolling code final steps.
Rolling Code Garage Door Opener Final Steps
NOTE:You have 30 seconds in which to initiate rolling
code final step 2, after completing rolling code
final step 1.
1. At the garage door opener motor (in the
garage), locate the “LEARN” or “TRAIN”
button. This can usually be found where the
hanging antenna wire is attached to the
garage door opener motor. Firmly push and
release the “LEARN” or “TRAIN” button.

2. Return to the vehicle and push the programmed HomeLink® button three times
(holding the button for two seconds each
time). If the garage door opener motor
operates, programming is complete.
3. Push the programmed HomeLink® button to confirm that the garage door opener motor
operates. If the garage door opener motor
does not operate, repeat the final steps for the
rolling code procedure.
Non-Rolling Code Garage Door Opener Final Steps

1. Push and hold the programmed HomeLink® button and observe the HomeLink® indicator
light. If the HomeLink® indicator light stays
on constantly, programming is complete.

2. Push the programmed HomeLink® button to confirm that the garage door opener motor
operates. If the garage door opener motor
does not operate, repeat the steps from the
beginning.
2

22_LX_OM_EN_USC_t.book Page 41

42GETTING TO KNOW YOUR VEHICLE
PROGRAMMING HOMELINK® TO A
M
ISCELLANEOUS DEVICE
The procedure on how to program HomeLink® to a
miscellaneous device follows the same procedure
as programming to a garage door opener
Ú page 41. Be sure to determine if the device has
a rolling code, or non-rolling code before beginning
the programming process.
NOTE:Canadian Radio Frequency (RF) laws require trans -
mitter signals to time-out (or quit) after several
seconds of transmission, which may not be long
enough for HomeLink® to pick up the signal during
programming. Similar to this Canadian law, some
U.S. gate operators are designed to time-out in the
same manner. The procedure may need to be
performed multiple times to successfully pair the
device to your HomeLink® buttons.
REPROGRAMMING A SINGLE
H
OMELINK® BUTTON
To reprogram a single HomeLink® button that has
been previously trained, without erasing all the
channels, follow the procedure below. Be sure to
determine whether the new device you want to
program the HomeLink® button to has a rolling
code, or non-rolling code.

1. Place the ignition in the ON/RUN position,
without starting the engine.

2. Push and hold the desired HomeLink® button until the HomeLink® indicator light begins to
flash after 20 seconds. Do not release the
button. 3.
Without releasing the button , proceed with
Step 2 in “Programming HomeLink® To A
Garage Door Opener” and follow all remaining
steps.
CANADIAN/GATE OPERATOR
P
ROGRAMMING
For programming transmitters in Canada/United
States that require the transmitter signals to
“time-out” after several seconds of transmission:
Canadian Radio Frequency (RF) laws require
transmitter signals to time-out (or quit) after
several seconds of transmission, which may not be
long enough for HomeLink® to pick up the signal
during programming. Similar to this Canadian law,
some U.S. gate operators are designed to time-out
in the same manner.
It may be helpful to unplug the device during the
cycling process to prevent possible overheating of
the garage door or gate motor.

1. Place the ignition in the ON/RUN position.

NOTE:For vehicles equipped with Keyless Enter ‘n Go™,
place the ignition in the RUN position. Make sure
while programming HomeLink® with the engine on
that your vehicle is outside of your garage, or that
the garage door remains open at all times.
WARNING!

Your motorized door or gate will open and close
while you are programming the universal trans -
mitter. Do not program the transmitter if people
or pets are in the path of the door or gate.

Do not run your vehicle in a closed garage or
confined area while programming the trans -
mitter. Exhaust gas from your vehicle contains
Carbon Monoxide (CO) which is odorless and
colorless. Carbon Monoxide is poisonous
when inhaled and can cause you and others to
be severely injured or killed.

22_LX_OM_EN_USC_t.book Page 42

GETTING TO KNOW YOUR VEHICLE43
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button
you wish to program while keeping the
HomeLink® indicator light in view.
3. Continue to push and hold the HomeLink® button while you push and release (cycle) your
hand-held transmitter every two seconds until
HomeLink® has successfully accepted the
frequency signal. The indicator light will flash
slowly and then rapidly when fully trained.
4. Watch for the HomeLink® indicator to change flash rates. When it changes, it is
programmed. It may take up to 30 seconds or
longer in rare cases. The garage door may
open and close while you are programming.
5. Push and hold the programmed HomeLink® button and observe the indicator light.
NOTE:
If the indicator light stays on constantly,
programming is complete and the garage
door/device should activate when the
HomeLink® button is pushed.
To program the two remaining HomeLink®
buttons, repeat each step for each
remaining button. DO NOT erase the chan -
nels. If you unplugged the garage door opener/device
for programming, plug it back in at this time.
Reprogramming A Single HomeLink® Button
(Canadian/Gate Operator)
To reprogram a channel that has been previously
trained, follow these steps:

1. Place the ignition in the ON/RUN position.

2. Press and hold the desired HomeLink® button
until the indicator light begins to flash after 20
seconds. Do not release the button.
3. Without releasing the button, proceed with “Canadian/Gate Operator Programming” Step
2 and follow all remaining steps.
SECURITY
It is advised to erase all channels before you sell or
turn in your vehicle.
To do this, push and hold the two outside buttons
for 20 seconds until the indicator flashes. Note
that all channels will be erased. Individual
channels cannot be erased.
The HomeLink® universal transmitter is disabled
when the Vehicle Security system is active.
TROUBLESHOOTING TIPS
If you are having trouble programming
HomeLink®, here are some of the most common
solutions:
Replace the battery in the garage door opener
hand-held transmitter.
Push the LEARN button on the garage door
opener to complete the training for a rolling
code.
Did you unplug the device for programming and
remember to plug it back in?
If you have any problems, or require assistance,
please call toll-free 1-800-355-3515 or, on the
Internet at
HomeLink.com for information or
assistance.
2

22_LX_OM_EN_USC_t.book Page 43

277
Folding Rear Seats
.......................................... 30Forward Collision Warning............................. 155Four-Way Hazard Flasher............................... 193Freeing A Stuck Vehicle................................. 206Fuel............................................................... 264Additives................................................... 265Clean Air.................................................... 265Ethanol...................................................... 265Gasoline.................................................... 264Gauge.......................................................... 80Materials Added........................................ 265Methanol................................................... 265Octane Rating................................. 264, 268Requirements........................................... 264Specifications............................................ 268Tank Capacity............................................ 267Fuses............................................................. 228
G
Garage Door Opener (HomeLink).................... 40Gasoline, Clean Air........................................ 265Gasoline, Reformulated................................. 265Gauges Fuel............................................................. 80Gear Ranges.................................................... 93Glass Cleaning............................................... 262Gross Axle Weight Rating..................... 119, 121Gross Vehicle Weight Rating................ 119, 120GVWR............................................................ 119
H
HazardDriving Through Flowing, Rising, Or Shallow Standing Water
.................................... 127Hazard Warning Flashers.............................. 193Head Restraints........................................ 35, 36Head Rests............................................... 35, 36Headlights.................................................... 240Automatic.................................................... 46Cleaning................................................... 260High Beam/Low Beam Select Switch.......... 45Lights On Reminder..................................... 47On With Wipers............................................ 46Passing........................................................ 46Switch.......................................................... 44Time Delay................................................... 46Washers................................................... 216Heated Mirrors................................................. 39Heated Seats................................................... 33Heater, Engine Block....................................... 89
High Beam/Low Beam Select (Dimmer) Switch... 45
Hill Start Assist.............................................. 150HitchesTrailer Towing........................................... 122Holder, Coin..................................................... 57HomeLink (Garage Door Opener)..................... 40Hood Prop........................................................ 65Hood Release.................................................. 65
I
Ignition.............................................................15Switch..........................................................15Inside Rearview Mirror........................... 37, 193Instrument Cluster....................................68, 70Descriptions.................................................83Display.................................................. 70, 73Instrument Panel Lens Cleaning................... 262Interior Appearance Care.............................. 261Interior Lights...................................................48
J
Jack Location................................................ 198Jack Operation.............................................. 198Jacking Instructions...................................... 198Jump Starting................................................ 201
K
Key FobArm The System
...........................................19Unlatch The Trunk.......................................13Key Fob Battery Service
(Remote Keyless Entry)....................................13Keyless Enter 'n Go™................................ 23, 86Enter The Trunk...........................................13Passive Entry...............................................23Passive Entry Programming.........................23Keys.................................................................12Replacement...............................................14
11

22_LX_OM_EN_USC_t.book Page 277

282
Towing Behind A Motorhome
......................... 126Traction......................................................... 126Traction Control............................................. 151Trailer Towing................................................ 120Hitches...................................................... 122Minimum Requirements............................ 123Tips........................................................... 125Trailer And Tongue Weight........................ 123Wiring........................................................ 124Trailer Towing Guide...................................... 122Trailer Weight................................................ 122Transfer Case Fluid................................................ 228, 269Maintenance............................................. 228Transmission................................................... 92Automatic........................................... 92, 227Fluid.......................................................... 269Maintenance............................................. 227Shifting........................................................ 91Transporting Pets.......................................... 189Tread Wear Indicators................................... 252Trunk Lid (Deck Lid)......................................... 65Trunk Release Remote Control........................ 65Turn Signals.............................................. 47, 83
U
UconnectUconnect Settings
..............................18, 129
Uconnect 4C/4C Nav With 8.4-Inch Display.... 129
Uconnect Settings
Customer Programmable Features.. 18, 23, 129
Passive Entry Programming......................... 23Uniform Tire Quality Grades.......................... 259Universal Garage Door Opener
(Homelink®)
b
............................................. 40Unleaded Gasoline....................................... 264Untwisting Procedure, Seat Belt................... 164USB.................................................................. 58
V
Vanity Mirrors.................................................. 37Vehicle Certification Label............................ 119Vehicle Identification Number (VIN).............. 263Vehicle Loading.......................... 119, 120, 247Vehicle Maintenance.................................... 217Vehicle Modifications/Alterations...................... 8Vehicle Security Alarm..................................... 19Vehicle Storage.......................................55, 260Voice Command............................................... 27Voice Recognition System (VR)........................ 27
W
Warning Flashers, Hazard............................. 193Warning Lights
(Instrument Cluster Descriptions)....................80Warranty Information.................................... 272Washer Adding Fluid.............................................. 216Washers, Windshield.................................... 216Washing Vehicle............................................ 260WaterDriving Through........................................ 127Wheel And Wheel Tire Care........................... 256Wheel And Wheel Tire Trim........................... 256Wind Buffeting.................................................63Window Fogging...............................................55Windows..........................................................61Power...........................................................61Reset Auto-Up..............................................62Windshield Defroster.................................... 190Windshield Washers........................................50Fluid.......................................................... 216Windshield Wiper Blades.............................. 221Windshield Wipers...........................................50Wipers Blade Replacement........................... 221Wipers, Rain Sensitive.....................................51

22_LX_OM_EN_USC_t.book Page 282