3-5
34. Once immediate safety hazards are con-
firmed not to exist, you may remove your hel-
met to more closely inspect your vehicle.
Check for external signs of wear, broken
parts, fluid leaks, cracks in the frame, sus-
pension damage, wheel damage, and so on.
Fuel, oil, and coolant usually give off a notice-
able odor.
5. If your vehicle will not restart or if it is unsafe to ride, then turn off all vehicle systems (en-
gine stop switch, main switch, and fuel cock),
and then signal or go for help.
Aftermarket Parts, Accessories, and Modifica-
tions
While you may find aftermarket products similar in
design and quality to genuine Yamaha accesso-
ries, recognize that some aftermarket accessories
or modifications are not suitable because of po-
tential safety hazards to you or others. Installing
aftermarket products or having other modifica-
tions performed to your vehicle that change any of
the vehicle’s design or operation characteristics
can put you and others at greater risk of serious
injury or death. You are responsible for injuries re-
lated to changes in the vehicle. Keep the following guidelines in mind, as well as those found in the
Loading section (page 7-6) when mounting acces-
sories.
Never install accessories that would impair the
performance of your ATV. Carefully inspect the
accessory before using it to make sure that it
does not in any way reduce ground clearance,
limit suspension travel, steering travel or control
operation.
Accessories fitted to the ATV can create insta-
bility due to improper weight distribution.
Bulky or large accessories may seriously affect
the stability of the ATV.
Certain accessories can displace the operator
from his or her normal riding position. This im-
proper position limits the freedom of movement
of the operator and may limit control ability,
therefore, such accessories are not recom-
mended.
Use caution when adding electrical accesso-
ries. If electrical accessories exceed the capac-
ity of the ATV’s electrical system, an electric
failure could result, which could cause a dan-
gerous loss of lights or engine power. Also, the
battery tends to discharge more quickly if elec-
trical accessories are added.
UBW464E0.book Page 5 Thursday, January 23, 2020 2:42 PM
5-14
5
NOTICEECB01091Never turn the adjusting mechanism beyond
the minimum and maximum settings. Adjust the spring preload as follows.
Turn the spring preload adjusting ring in direction
(a) to increase the spring preload and thereby
harden the suspension, and in direction (b) to de-
crease the spring preload and thereby soften the
suspension.
TIPA special wrench can be obtained at a Yamaha
dealer to make this adjustment.
1. Spring preload adjusting ring
2. Position indicator
1234 52
1
(a)
(b)
1. Special wrenchSpring preload settingW
Minimum (soft)WN
StandardW N
Maximum (hard)W R
1
UBW464E0.book Page 14 Thursday, January 23, 2020 2:42 PM
11-3
11
Transmission type:CVT automatic
Gear ratio: Transmission ratio:2.140–0.710 : 1
Forward gear: 10.967 (49/15 x 47/14)Front tire:Size:AT16x6.5-7
Manufacturer/model: DURO/DI2040Rear tire:Size:AT16x7-7
Manufacturer/model: DURO/DI2041Tire air pressure (measured on cold tires):Vehicle load:0.0–41.0 kg (0–90 lb)
Recommended: Front:15.0 kPa (0.150 kgf/cm², 2.2 psi)
Rear: 15.0 kPa (0.150 kgf/cm², 2.2 psi)
Minimum:
Front:12.0 kPa (0.120 kgf/cm², 1.7 psi)
Rear:
12.0 kPa (0.120 kgf/cm², 1.7 psi)
Front wheel:Rim size:7 x 5.2ATRear wheel:Rim size:7 x 5.2ATFront brake:Type:
Mechanical leading, trailing drum brakeRear brake:Type:Mechanical leading, trailing drum brakeFront suspension:Type:Swing axle
Spring: Coil spring
Shock absorber:
Gas-hydraulic damper
Wheel travel: 60 mm (2.4 in)Rear suspension:Type:
Swingarm
Spring: Coil spring
Shock absorber: Gas-hydraulic damper
Wheel travel:
51 mm (2.0 in)
UBW464E0.book Page 3 Thursday, January 23, 2020 2:42 PM
