2021 YAMAHA YFM90R battery

9-33
9
NOTICEECB00942Always keep the battery charged. Storing the
battery in a discharged state for an extended
period of time will cause permanent battery
damage.
 Do not store the battery in an excessively
cold or warm place [below freezing or above
30 °C (90 °F)]. To install the battery
1. Place the battery in its compartment.
2. Connect the positive battery lead first, then connect the negative battery lead by installing
their bolt. NOTICE: When installing the bat-
tery, the main switch must be off, and the
positive lead must be connected before
the negative lead.
[ECB01111]
3. Hook the battery band.
4. Install the seat. (See page 5-13.)TIP Make sure the positive and negative battery
leads are installed as shown.
 Fully charge the battery before installing it. 1. Positive battery lead (red)
2. Negative battery lead (black)
2
1
UBD365E0.book Page 33 Monday, January 27, 2020 9:05 AM

9-37
9
EBU25754Troubleshooting chart
Check the fuel level in
the fuel tank.1. Fuel
There is enough fuel.There is no fuel.
Check the battery.
Supply fuel.
The engine does not start.
Check the battery.
The engine does not start.
Check the ignition.
Operate the electric starter.4. Compression
There is compression.
There is no compression.
The engine does not start. Have a Yamaha dealer check the ATV.Have a Yamaha dealer check the ATV.
Remove the spark plug
and check the electrodes.3. Ignition
Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug. Have a Yamaha dealer check the ATV.
The engine does not start.
Check the compression.
Operate the electric starter.2. Battery
The engine turns over
quickly.
The engine turns over
slowly.
The battery is good.Check the battery lead connections,
and have a Yamaha dealer charge
the battery if necessary.
DryWet
Open the throttle halfway and operate
the electric starter.
UBD365E0.book Page 37 Monday, January 27, 2020 9:05 AM

10-3
10
e. Install the spark plug and the spark plug
cap.
6. Lubricate all control cables and the pivoting points of all levers.
7. Put the frame on stands or blocks to raise all wheels off the ground. (Alternatively, turn the
wheels each month to prevent the tires from
degrading in one spot.)
8. Cover the muffler outlet with a plastic bag to prevent moisture from entering it.
9. Remove the battery and fully charge it. (See page 9-31.)
UBD365E0.book Page 3 Monday, January 27, 2020 9:05 AM

11-4
11
Electrical system:System voltage:12 V
Ignition system:
CDI
Charging system: AC magnetoBattery:Model:
GTX5L-BS
Voltage, capacity: 12 V, 4.0 AhLights:Neutral indicator light:
3.5 W
Reverse indicator light: 3.5 WFuses:Main fuse:
7.5 AEBU30403Noise and vibration levels statement (for Eu-
rope)
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required. Factors that influence the actual level of exposure
of work-force include the characteristics of the
work room, the other sources of noise, etc. i.e. the
number of machines and other adjacent process-
es, and the length of time for which an operator is
exposed to the noise. Also the permissible expo-
sure level can vary from country. This information,
however, will enable the user of the machine to
make a better evaluation of the hazard and risk.
EBU38670CO2 emissions levels statement (for Europe)
This CO2 measurement results from testing over a
fixed test cycle under laboratory conditions a(n)
(parent) engine representative of the engine type
(engine family) and shall not imply or express any
guarantee of the performance of a particular en-
gine.
UBD365E0.book Page 4 Monday, January 27, 2020 9:05 AM

12-1
12
INDEX
AAccessories and loading ................................................ 7-6
Air filter element, cleaning ............................................ 9-15BBattery .......................................................................... 9-31
Brake lever free play, adjusting the front ..................... 9-23
Brake lever free play (rear), adjusting ........................... 9-24
Brake lever, front ............................................................ 5-5
Brake lever, rear ............................................................. 5-5
Brake levers, checking and lubricating ........................ 9-28
Brakes .......................................................................... 9-21
Brakes, front and rear .................................................... 6-3CCables, checking and lubricating ................................. 9-28
Carburetor, adjusting ...................................................9-19
Chassis fasteners ........................................................... 6-6
Cleaning ....................................................................... 10-1DDrive chain ..................................................................... 6-3
Drive chain, lubricating ................................................ 9-27
Drive chain slack .......................................................... 9-25
Drive select lever ............................................................ 5-6
Drive select lever and driving in reverse ........................ 7-3EEngine break-in .............................................................. 7-4
Engine, cold start ........................................................... 7-1
Engine idling speed ...................................................... 9-19
Engine oil .............................................................. 6-3, 9-10
Engine, starting a warm ................................................. 7-3Engine stop switch ......................................................... 5-2
FFront and rear brake shoes, checking ......................... 9-21
Front arm pivots, lubricating ........................................ 9-29
Front knuckle pivots, lubricating .................................. 9-30
Fuel ........................................................................ 5-9, 6-3
Fuel cock ...................................................................... 5-10
Fuel tank cap ................................................................. 5-8
Fuse, replacing ............................................................. 9-34HHandlebar switches ....................................................... 5-2IIdentification numbers ................................................... 1-1
Indicator lights ............................................................... 5-1
Instruments and switches .............................................. 6-6KKickstarter ...................................................................... 5-7LLabel locations ............................................................... 2-1MMain switch .................................................................... 5-1
Maintenance and lubrication chart ................................ 9-5
Maintenance chart, emission control system ................ 9-3
Model label .................................................................... 1-1NNeutral indicator light ..................................................... 5-1OOwner’s Manual and tool kit .......................................... 9-2
UBD365E0.book Page 1 Monday, January 27, 2020 9:05 AM