2021 YAMAHA TMAX display

Instrument and control functions
5-9
5 
If the am bient temperature is 20
°C (68 °F) or hi gher, do not set
the seat heater to the hi gh set-
ting .
 If the seat b ecomes worn or
d amag ed , stop usin g the seat
heater an d replace the seat.
Changing the information displayThe information display items are
grouped into 3 display pages.
Push the “ ” or “ ” side of the se-
lect switch to rotate among the 3 dis-
play pages.TIPThe items for each display page can be
customized. (See page 5-14.)
Odometer:The odometer shows the total distance
traveled by the vehicle.
Tripmeters:
tance traveled since they were last set
to zero.
To reset a tripmeter, use the select
switch to select the information display
page that contains the tripmeter you
want to reset. Push the Ž side of
the select switch for one second so
that the tripmeter flashes, and then push the Ž side of the select switch
again for one second while the tripme-
ter is flashing.
TIP
The odometer will lock at 999999.
 The tripmeters will reset and con-
tinue counting after 9999.9 is
reached.When approximately 3.0 L (0.79 US
gal, 0.66 Imp.gal) of fuel remains in the
fuel tank, the last segment of the fuel
meter starts flashing. In addition, the
information display will automatically
change to the fuel reserve tripmeter
mode “F-TRIP” and start counting the
distance traveled from that point.
In this case, push the select switch to
switch the display in the following or-
der:
F-TRIP Display–1 Display–2
Display–3 F-TRIP
UB3TE1E0.book Page 9 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-10
5
If you do not reset the fuel reserve trip-
meter manually, it will reset automati-
cally after refueling and traveling 5 km
(3 mi).
TIPYou cannot enter setting mode (page
Estimated traveling range:The estimated distance that can be
traveled with the remaining fuel under
the current riding conditions is shown.
Ambient temperature:This shows the ambient temperature
from …9 °C to 50 °C in 1 °C increments.
The temperature displayed may vary
from the actual ambient temperature.
TIP
–9 °C will be displayed even if the
detected temperature is lower.
 50 °C will be displayed even if the
detected temperature is higher.
 The accuracy of the temperature
reading may be affected when rid-
ing under 20 km/h (12 mi/h) or
when stopped at traffic signals
and railroad crossings.Average fuel consumption:The average fuel consumption mode
“F.AVE” can be set to “km/L” or
“L/100km”. For UK-spec vehicles:
“MPG”. (See page 5-14.)
To reset the average fuel consumption,
use the select switch to select the in-
formation display page that contains
the average fuel consumption display.
Push the “ ” side of the select switch
so that the average fuel consumption
display flashes, and then push the “ ” side of the select switch again
for 1 second while the display is flash-
ing.
TIPAfter resetting the average fuel con-

until the vehicle has traveled 1 km (0.6
mi).NOTICE
ECA15474
If there is a malfunction, “– –.–” will
b
e continuously displaye d. Have a
Yamaha dealer check the vehicle.Instantaneous fuel consumption:The instantaneous fuel consumption
mode “CRNT.F” can be set to “km/L”
or “L/100km”. For UK-spec vehicles:
“MPG”. (See page 5-14.)TIPIf traveling at speeds under 10 km/h (6

UB3TE1E0.book Page 10 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-11
5
NOTICE
ECA15474
If there is a malfunction, “– –.–” will
b e continuously displaye d. Have a
Yamaha dealer check the vehicle.Setting mode
Stop the vehicle and then push the
“MENU” switch for 2 seconds to enter
the setting mode. To exit the setting
mode and return to the standard dis-
play mode, push the “MENU” switch
again for 2 seconds or
select “ ”.TIPWhen the malfunction indicator light is
on, setting mode cannot be entered.
Menu items
Grip warmer settings1. Use the select switch to highlight “Grip Warmer”.
2. Push the “MENU” switch. The grip warmer setting display will be
shown.
1. Setting mode display
1
Cate gory Description
This function allows you to
set the low, middle, and
high settings to 10 tem-
perature levels.
This function allows you to
set the low, middle, and
high settings to 10 tem-
perature levels.
This function allows you to
turn the traction control
system on or off.
This function allows you to
check and reset the oil
change interval (indicator),
V-Belt change interval (in-
dicator), and the “FREE”
maintenance interval.
This function allows you to
switch the fuel consump-
tion units between
“L/100km” and “km/L”.
For UK-spec vehicles: this
function is not available.
This function allows you to
change the items shown in
3 information displays.
This function allows you to
adjust the brightness of
the instrument panel.
This function allows you to
set the clock.Grip WarmerSeat HeaterTraction ControlMaintenance
UnitDisplayBrightnessClock
This function allows you to
reset all items to their fac-
tory preset or default set-
tings; excepting the
odometer, clock, and
maintenance counter
items “Oil” and “V-Belt”.
All Reset
UB3TE1E0.book Page 11 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-12
5
3. Push the “MENU” switch. The
temperature level for the high set-
ting will be highlighted.
Use the select switch to set the
temperature level, and then push
the “MENU” switch. 4. Use the select switch to highlight
“Mid” or “Low”, and then change
the setting using the same proce-
dure that was used for the high
setting.
5. When you finished changing the settings, use the select switch to
highlight “ ”, and then push the
“MENU” switch to return to the
menu screen.
Seat heater settings
1. Use the select switch to highlight “Seat Heater”.
2. Push the “MENU” switch. The seat heater setting display will be
shown. 3. Push the “MENU” switch. The
temperature level for the high set-
ting will be highlighted.
Use the select switch to set the
temperature level, and then push
the “MENU” switch.
UB3TE1E0.book Page 12 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-13
5 4. Use the select switch to highlight
“Mid” or “Low”, and then change
the setting using the same proce-
dure that was used for the high
setting.
5. When you finished changing the settings, use the select switch to
highlight “ ”, and then push the
“MENU” switch to return to the
menu screen.
Traction control system settings
1. Use the select switch to highlight “Traction Control”.
2. Push the “MENU” switch. The traction control system setting
display will be shown. 3. To set the traction control system
to “OFF”, push the select
switch “ ” side for 2 seconds.
4. To set the traction control system to “ON” again, push the select
switch “ ”.
TIPWhen the vehicle is powered on, the
traction control system is automatically
5. When you finished changing the
to return to the menu screen.
Resettin g the maintenance counters
1. Use the select switch to highlight “Maintenance”.
2. Push the “MENU” switch, and then use the select switch to se-
lect the item to reset.
UB3TE1E0.book Page 13 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-14
5
3. Push the “MENU” switch, and af-
ter the selected item is highlight-
ed, push the select switch “ ”
for one second.
4. When you finished resetting, use the select switch to highlight “ ”,
and then push the “MENU” switch
to return to the menu screen. Selectin
g the units
TIPU.K. specification vehicles only: This
function does not indicate on setting
mode display and cannot be selected.1. Use the select switch to highlight
“Unit”.
2. Push the “MENU” switch. The unit setting display will be shown. 3. Use the select switch to select
“L/100km” or “km/L”.
4. Push the “MENU” switch to make the selection and return to the
menu screen.
Selectin g the d isplay items
1. Use the select switch to highlight “Display Change”.
UB3TE1E0.book Page 14 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-15
5 2. Push the “MENU” switch, use the
select switch to highlight the dis-
play to change, and then push the
“MENU” switch again.
3. Use the select switch to highlight the item to change, and then push
the “MENU” switch.
TIPDisplay item order is as follows.4. Use the select switch to select theitem to show, and then push the
5. When you finished changing the
settings, use the select switch to
highlight Ž, and then push the

previous display.
6. Use the select switch to highlight Ž, and then push the

menu screen.
Meter panel brightness
1. Use the select switch to highlight
2.
3. Use the select switch to select the desired brightness level.
A.TEMP TRIP-1 TRIP-2
ODO
CRNT.F F.AVG RANGE
UB3TE1E0.book Page 15 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-16
5
4. Push the “MENU” switch to return
to the menu screen.
Setting the clock
TIPThe clock uses a 12-hour time system.1. Use the select switch to highlight 2.
3. When the hour digits are highlight-
ed, use the select switch to set the
hours.
4. minute digits are highlighted.
5. Use the select switch to set the minutes. 6.
to the menu screen.
Resetting all of the display items
1. Use the select switch to highlight
2.
3. Use the select switch to highlight
switch. All items are reset to facto-
ry preset or default settings.
UB3TE1E0.book Page 16 Friday, September 11, 2020 8:48 AM