3-5
3ungrounded or broken wiring. Visually check
for broken wiring and leaking fuel. Leaking
fuel can be confirmed by the odor of gasoline.
4. Once immediate safety hazards are con- firmed not to exist, you may remove your hel-
met to more closely inspect your vehicle.
Check for external signs of wear, broken
parts, fluid leaks, cracks in the frame, sus-
pension damage, wheel damage, and so on.
Fuel, oil, and coolant usually give off a notice-
able odor.
5. If your vehicle will not restart or if it is unsafe to ride, then turn off all vehicle systems (en-
gine stop switch, main switch, and fuel cock),
and then signal or go for help.
Aftermarket Parts, Accessories, and Modifica-
tions
While you may find aftermarket products similar in
design and quality to genuine Yamaha accesso-
ries, recognize that some aftermarket accessories
or modifications are not suitable because of po-
tential safety hazards to you or others. Installing
aftermarket products or having other modifica-
tions performed to your vehicle that change any of
the vehicle’s design or operation characteristics
can put you and others at greater risk of serious injury or death. You are responsible for injuries re-
lated to changes in the vehicle. Keep the following
guidelines in mind, as well as those found in the
Loading section (page 7-6) when mounting acces-
sories.
Never install accessories that would impair the
performance of your ATV. Carefully inspect the
accessory before using it to make sure that it
does not in any way reduce ground clearance,
limit suspension travel, steering travel or control
operation.
Accessories fitted to the ATV can create insta-
bility due to improper weight distribution.
Bulky or large accessories may seriously affect
the stability of the ATV.
Certain accessories can displace the operator
from his or her normal riding position. This im-
proper position limits the freedom of movement
of the operator and may limit control ability,
therefore, such accessories are not recom-
mended.
Use caution when adding electrical accesso-
ries. If electrical accessories exceed the capac-
ity of the ATV’s electrical system, an electric
failure could result, which could cause a dan-
UBFE60E0.book Page 5 Tuesday, August 18, 2020 10:50 AM
11-4
11
Manufacturer/model:MAXXIS/MU01Y (BFEC, BFEG)
MAXXIS/MU06Y (BFE1, BFE8)Tire air pressure (measured on cold tires):No cargo or trailer:
Recommended: Front:
35.0 kPa (0.350 kgf/cm², 5.0 psi)
Rear: 30.0 kPa (0.300 kgf/cm², 4.4 psi) (BFE1, BFE8)
35.0 kPa (0.350 kgf/cm², 5.0 psi) (BFEC, BFEG)
Minimum: Front:
32.0 kPa (0.320 kgf/cm², 4.6 psi)
Rear: 27.0 kPa (0.270 kgf/cm², 4.0 psi) (BFE1, BFE8)
32.0 kPa (0.320 kgf/cm², 4.6 psi) (BFEC, BFEG)
With cargo or trailer:
Recommended:
Front:50.0 kPa (0.500 kgf/cm², 7.3 psi)
Rear:
50.0 kPa (0.500 kgf/cm², 7.3 psi)
Minimum: Front:
45.0 kPa (0.450 kgf/cm², 6.5 psi)
Rear: 45.0 kPa (0.450 kgf/cm², 6.5 psi)Front wheel:Rim size:
12 x 6.0 AT (BFE1, BFE8)
14 x 8.0 AT (BFEC, BFEG)
Rear wheel:Rim size:12 x 7.5 AT (BFE1, BFE8)
14 x 8.0 AT (BFEC, BFEG)Front brake:Type:
Hydraulic disc brakeRear brake:Type:Hydraulic disc brakeBrake fluid:Specified brake fluid:DOT 4Front suspension:Type:
Double wishbone
Spring: Coil spring
Shock absorber: Hydraulic damper
Wheel travel:
193 mm (7.6 in)Rear suspension:Type:Double wishbone
Spring:
Coil spring
Shock absorber: Hydraulic damper
Wheel travel: 232 mm (9.1 in)
UBFE60E0.book Page 4 Tuesday, August 18, 2020 10:50 AM
