2021 TOYOTA MIRAI tires

40
Dealer Service verification:
D
ate: Mileage:
Dealer Service verification:
D
ate: Mileage:
110,000 miles or 132 months
■Check installation of driver’s floor mat
■Inspect and adjust all fluid levels1
■Inspect FC HV battery cooling intake filter2
■Inspect wiper blades
■Replace cabin air filter
■Rotate tires
■ Visually inspect brake linings/drums
and brake pads/discs
Inspect the following: ■Fuel cell air filter
■ Fuel cell cooling system for leaks
■Hydrogen sensor
■ Hydrogen supply system for leaks
and damage
■ Hydrogen tank (with valve) for leaks
and damage
■ Hydrogen tank band for looseness
and damage

■Additional MainteAdditional Maintenance Items for
Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Inspect ball joints and dust covers
■Inspect drive shaft boots
■Inspect steering linkage and boots
■ Tighten nuts and bolts on chassis
and body
Driving while towing, using a car-top
carrier, or heavy vehicle loading:
4
■ Tighten nuts and bolts on chassis
and body
115,000 miles or 138 months
■Check installation of driver’s floor mat
■Inspect and adjust all fluid levels1
■Inspect FC HV battery cooling intake filter2
■Inspect wiper blades
■Rotate tires
■ Visually inspect brake linings/drums
and brake pads/discs
Additional Maintenance Items for
Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Inspect ball joints and dust covers
■Inspect drive shaft boots
■Inspect fuel cell air filter
■Inspect steering linkage and boots
■ Tighten nuts and bolts on chassis
and body
Extensive idling and/or low speed driving
for a long distance such as police, taxi
or door-to-door delivery use:
■ Inspect hydrogen supply system for
leaks and damage
■ Inspect hydrogen tank (with valve)
for leaks and damage
■Inspect hydrogen tank band for damage
Driving while towing, using a car-top
carrier, or heavy vehicle loading:
4
■ Tighten nuts and bolts on chassis
and body
Operating on rough or muddy roads, or
roads with melted snow:
■ Inspect hydrogen supply system for
leaks and damage
■ Inspect hydrogen tank (with valve) for
leaks and damage
■Inspect hydrogen tank band for damage



Maintenance Log
MAINTENANCE LOG
MAINTENANCE

41
Dealer Service verification:
D
ate: Mileage:
120,000 miles or 144 months
■Check installation of driver’s floor mat
■Clean FC HV battery cooling intake filter2
■Inspect and adjust all fluid levels1
■Inspect wiper blades
■Replace breather pipe tip part (Gore film)
■Replace cabin air filter
■Replace fuel cell air filter
■Replace ion exchanger element
■Rotate tires
Inspect the following:
_ B

all joints and dust covers
_ B

rake lines and hoses
_ B

rake linings/drums and
brake pads/discs
5
_ Dr ive shaft boots
_F

uel cell coolant level
_ F

uel cell cooling system for leaks
_ H

ybrid transaxle for signs of leakage
_H

ydrogen sensor
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:4
■Replace hybrid transaxle fluid
■Tighten nuts and bolts on chassis and body
1 Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed
component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on
inspection results.
2 Visually check the FC HV battery cooling intake filter for dirt or dust every 5,000 miles and clean if necessary. Clean every
20,000 miles.
3 Perform these service items only if you drive primarily under the conditions indicated.4 N ot all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.5 Inspect thickness measurement and disc runout.6 Replace tank (with valve) every 15 years or 180 months whichever comes first.7 Replace inverter coolant at 150,000 miles and every 50,000 miles thereafter.
_
H ydrogen supply system for leaks
and damag
e
_ H ydrogen tank (with valve) for leaks
and damage6
_ H ydrogen tank band for looseness
and damage
_ I

nverter coolant level
7
_ S teering gear
_S

teering linkage and boots
Maintenance Log
MAINTENANCE LOG
MAINTENANCE

44
EXPLANATION OF MAINTENANCE ITEMS
Inverter Coolant
Drain the cooling system and refill with an
ethylene-glycol type coolant. Inspect hoses
and connections for corrosion and leaks.
Tighten connections and replace parts
when necessary.
Inspect at specified inter

vals. When performing
inspections, check that the coolant level is
between the “FULL” and “LOW” lines on the
see-through reservoir tank.
Notice: A qualified technician should perform
this operation.
Use the following product:
“Genuine Toyota Super Long-Life Coolant.”
NOTE: Replace inverter coolant at 150,000
miles and every 50,000 miles thereafter.
Ion Exchanger Element
It is necessary to replace the element within
the Ion Exchanger assembly periodically in
order to prevent degradation of the electrical
generating efficiency of the FC stack.
Notice: A qualified technician should perform
this operation.
Nuts and Bolts on Chassis
and Body
Retighten the seat-mounting bolts and
front/rear suspension member retaining
bolts to specified torque.
Radiator, Condenser, Hoses
and/or Intercooler
Inspect for damage, debris, corrosion,
kinks, cracks, rot, clogging and leaks.
Have any problem repaired immediately
by a qualified technician.
Steering Gear
Inspect for signs of leakage. If you
discover any leakage, have it repaired
immedia
tely by a qualified technician.
Steering Linkage and Boots
With the vehicle stopped, check for
excessive freeplay in the steering wheel.
Inspect
the linkage for bending and
damage and the dust boots for
deterioration, cracks and damage.
Replace any damaged parts. A qualified
technician should
perform these operations.
Tire Rotation
Tires should be rotated according to the
instructions in the Owner’s Manual. When
rotating tires, check for damage and
uneven wear.
Replace if necessary.
Wiper Blades
The wiper blades should not show
any signs of cracking, splitting, wear ,
contamina
tion or deformation. The
wiper blades should clear the windshield
without streaking or skipping.
Maintenance Log
MAINTENANCE