2021 SUZUKI JIMNY sensor

OPERATING YOUR VEHICLE
Lane departure warning
When you are operating at a speed of approximately 60 km/h (37 mph) or ov~r and the dual sensor judges that your vehi­cle is to deviate from the running lane, the following warnings will work. , The lane departure warning indicator light will blink . A message will appear on the informa­tion display The steering wheel will vibrate
Indicator light
3-33
Information display
78RB03036
A WARNING
• The lane departure warning may not be suitable for every situation. Also the system is not designed to avoid the lane deviations automati~ cally. Do not rely excessively on the system and always drive in a safe manner. Depending on road surface condi­tions, you may n~t feel the vibra­tion of the steering wheel even when the lane departure warning works. For safety reasons, do not check the operation of the system by yourself.
Situations where the system does not activate Under the following situations, the system does not activate. , When dual sensor brake support indica­tor light and lane departu_re warni~g i~di­cator light are 1nitially lighting immediately after the ignition switch is turned to "ON" When the following switches are pushed and the system is turned off: -Lane departure warning OFF switch -ESP® OFF switch When operated the hazard warning switch When the dual sensor is temporarily stopped or malfunctioning
When the system judges that the inten­tional lane change, such as during or after fiashing the turn signal lights
Situations where the system may not activate properly Under the following situations, the system may not activate. , When you suddenly close to the partition
lines When driving on sharp curves When you do not return to inside of th_e lane after the lane departure warning 1s activated When the electric power steering light
comes on
If the dual sensor cannot detect partition lines except for above situations, t~~ _sys­tem may also not activate. Refer to Situa­tions where the dual sensor may not activate properly" in this section for details.

Situations where the system may acti­vate by chance Under the following situations, the system may activate. • When there are a lot of lines in the run­ning lane When there is a shadow (for example, the shadow of the guardrail) parallel to the partition line When partition line is in the shadows When partition lines are drawn doubly When there is a liner paint on the road of a construction zone because the previ­ous line has not been erased completely When there is repair marks on the road or a boundary between asphalt and snow When there is tyre marks on snow-cov­ered or wet road When driving in the place without parti­tion lines (such as a tailgate or check­point, or at an intersection, etc.) When driving on the road diverges, merges, etc. When driving on an unpaved or rough road
Vehicle swaying warning
When you are operating at a speed of approximately 60 km/h (37 mph) or over and the vehicle swaying warning judges that your vehicle is unsteadiness by detecting the meandering patterns or lane departure warning is activate_d in a s_hort period of time in a row following warnings will work. The lane departure warning indicator light will blink A message will appear on the informa­tion display The interior buzzer will intermittently beep
~CO)
A
Indicator Information light display
~
• 78RB03037
OPERATING YOUR VEHICLE
.A. WARNING
The vehicle swaying warning may not be suitable for every situation. Also, the system is not designed t? avoid the unsteadiness of the vehi­cle automatically. Do not rely excessively on the system and always drive in a safe manner. For safety reasons, do not check the operation of the system by yourself.
NOTE: Vehicle swaying warning by the meander­ing pattern of the vehicle in the lane is judged based on the driving data over the past several tens of minutes, so the sys­tem does not activate when right after swaying.
Situations where the system does not activate Under the following situations, the system does not activate. When dual sensor brake support indica­tor light and lane departure warning indi­cator light are initially lighting immediately after the ignition switch is turned to "ON". When the following switches are pushed and the system is turned off: -Lane departure warning OFF switch -ESP® OFF switch When the dual sensor is temporarily stopped or malfunctioning
3-34

OPERATING YOUR VEHICLE
Situations where the system may not activate properly Under the following situations, the system may not activate. • Right after lane changing
If the dual sensor cannot detect partition lines except for above situations, the sys­tem may also not activate. Refer to "Situa­tions where the dual sensor may not activate properly" in this section for details.
High beam assist
After the auto high beam switch operation, head light is turned ON with the lighting control lever on "Auto" position when the ambient becomes dark, the system is acti­vated. When the high beam assist is acti­vated, high beam assist indicator light (green) comes on.
Under the any of following situations, the low beam turns on. • When vehicle speed is approximately 35 km/h (21.7 mph) or under When the front of the vehicle is bright When the vehicle in front of you turned on the lights There are many street lamps in front of you
Under the all of the following conditions are met, the high beams (main beams) turns on.
3-35
When vehicle speed is approximately 40 km/h (24.9 mph) or over When the front of the vehicle is dark When the vehicle in front of you is driv­ing without lights • There is few street lamps in front of you
A. WARNING
• High beam assist has limits and may not function properly depend­ing on the surrou.nding environ­ment. Always drive in a safe manner, switch manually to the low beams and high beams (main beams), if necessary. Switching of the low beams and high beams (main beams) it might not match the feeling of the driver.
NOTE: Light vehicle such as a bicycle might not detect. When the sudden acceleration, high beam assist might not operate for a few seconds, even if vehicle speed exceeds 40kmlh (24.9 mph).
How to use High beam assist
78RB03009
When the ignition switch is turned to "ON", switch the lighting control lever to "AUTO" position and then push this lever forward. High beam assist indicator light comes on in green.
To cancel the function, pull the lever toward you.
f,
52RM20740

Situations where the system does not activate When the high beam assist warning light (orange) comes on by the temporary stop or malfunction of system.
NOTE: When the function of the dual sensor brake support is temporarily stopped, high beam assist will be temporarily stopped. Refer to "Temporary stop or failure of the dual sen­sor'' in this section for details.
When high beam assist warning light (orange) is initially lighting immediately after the ignition switch is turned to "ON".
Under the following situations, high beam may not automatically switched to low beam. When you pass by an oncoming vehicle on a curvy road where the visibility is poor When another vehicle crosses in front of you When the vehicle in front of you glimpses due to continuous curves, medial strip or street trees When the vehicle in front of you approaches towards you from the far lane When the vehicle in front of you is driv­ing without lights
For the following cause, there is case where the switching timing of the high beam and low beam is varied. When the lights of the vehicle in front of you is dark When only one side of the lights of the vehicle in front of you is turned on The directions and movements of the vehicle in front of you When the vehicle in front of you is a motorcycle When driving on the following roads -On sharp curves or extremely rough surfaces -On a steep slope
When your vehicle is weighed down by heavy items in the luggage compartment or rear seat
OPERATING YOUR VEHICLE
Under the following situations, the brightness of the surrounding area can not be detected accurately, and there is a case where the high beam is a nui­sance to pedestrians or the vehicle ahead, or low beam will remain to con­tinue. In these cases, change high beam or low beam manually. When lights are similar to headlights or taillights are around When the vehicle in front of you is driv­ing without lights When the headlights of oncoming vehi­cle are covered in dirt or discolored When the optical axis of the headlight of oncoming vehicle is deviated When the brightness is changed extremely and continuously When driving on an undulated or bumpy road When driving on the road with a lot of curves When there are things that strongly reflect light, such as road signs or mir­rors in front of the vehicle When the rear part of the preceding vehicle strongly reflects light, such as containers When the headlights of your car are damaged or covered in dirt When the vehicle is tilted due to the flat tyres or being towed
3-36

OPERATING YOUR VEHICLE
Other than the described above, the dual sensor cannot be detected the vehicle in front of you or light source, and there is a case where high beam assist may not acti­vate properly. Refer to "Situations where the dual sensor may not activate properly" in this section for details.
Under the following situations, switch high beam or low beam manually, When switching back and forth between the high beams (main beams) and low beams frequently When there is a problem using the high beams (main beams) When it is considered disturbing to other drivers or pedestrians
There is a case where high beams (main beams) is switched to low beams by the fog lights of the vehicle in front of you.
Street lights, traffic signals, and illumina­tion of billboards or signs may cause the high beams (main beams) to switch to the low beams, or low beam to remain on.
3-37
Dual sensor brake support OFF switch
You can turn off the dual sensor brake support system. In the following situations, push and hold the dual sensor brake support OFF switch as unexpected dangers may be possible if ii is activated. -When the vehicle is placed upon ates­ter such as when undergoing a vehicle inspection -When the vehicle is put up on a lift, and the tyres are idling -When the vehicle is being towed -When the vehicle is being carried on a car carrier -When the vehicle is being operated on a race track -When there is vinyl curtains or pendu­lous branches in front of the vehicle -When driving in the field covered with grown grass -When using an automatic car washer -When the vehicle is placed upon a car elevator or placed in a mechanical parking lot -With a spare tyre or snow chains equipped -When you have a temporarily repaired flat tyre -When you have an accident or break­down -When the automatic brake system is activated frequently
-When tyres are not inflated to the rec­ommended tyre pressure -With worn tyres equipped -With non-specified sized tyres or wheels equipped -With a modified suspension equipped -When attaching an item which inter-feres with the visibility of the dual sen­sor -When the vehicle is being weighed down by heavy items -When the vehicle is used to tow a trailer
78RB03010

When you want to turn off the system, push and hold the dual s_ensor_ brake support OFF switch (1) until the interior buzzer beeps and the dual sensor brake support OFF indicator light (2) comes on.
Perform the following method to turn the system back on. • Push and hold the dual sensor brake support OFF switch (1) until the interior buzzer beeps and the dual sensor brake support OFF indicator light (2) goes off. Turn off the engine and then turn it on again.
A WARNING
If you attempt to press the dual sen­sor brake support OFF switch while driving, you could lose control of the vehicle. Do not press the dual sensor brake support OFF switch while driving.
Lane departure warning OFF switch
You can turn off the lane departure warn­ing and the vehicle swaying warning.
i~ (2) -
OFF
~i
□ ~ (1) ii _____ Jj
78RB03011
When you want to turn off the system, push and hold the lane departure warn­ing OFF switch (1) until the interior buzzer beeps and the lane departure warning OFF indicator light (2) comes
on.
Perform the following method to turn the system back on. • Push and hold the lane departure warn­ing OFF switch (1) until the interior buzzer beeps and the lane departure warning OFF indicator light (2) goes off.
OPERATING YOUR VEHICLE
A WARNING
If you attempt to press the lane departure warning OFF switch while driving, you could lose control of the vehicle. Do not press the lane departure warning OFF switch while driving.
·NOTE: Once the system is turned off, it does not turn on automatically, even if you turn off the engine and then starl the engine again. To turn the system back on, push the switch again.
3-38

OPERATING YOUR VEHICLE
Traffic sign recognition
(if equipped)
When the vehicle with the dual sensor passes the traffic sign, the traffic sign is shown on the information display on the cluster meter in order to notify the driver. This system may not work properly outside Europe.
60
..
A WARNING
The function of the traffic sign recog­nition has limits and may not func­tion properly depending on the driving conditions of circumstances. Do not rely excessively on this func­tion and always drive in a safe man~ ner.
3-39
NOTE: The traffic sign may be shown with delay on the information display depending on the circumstances and conditions of the vehicle The number of the traffic sign for this function shows up to three signs on the information display The traffic signs are disappeared on the information display under the following situations -When the vehicle was run in constant distance after showing the traffic signs on the information display (except for regulation end sign}, -When a period of time passed after the traffic signs on the information dis­play (only for regulation end sign), -When turning right or left with the turn signal lights blinked, -For manual transmission vehicle, the gearshift lever is in "R" position, for automatic transmission vehicle, the gearshift lever is in "P" or "R" position (except for speed limit sign). To change the traffic sign recognition setting, select "Sign recog." in "Setting mode" on the information display. Then, select "ON" or "OFF"
When the ignition switch was turned "OFF" with the speed limit sign shown on the information display and then the igni­tion switch is fumed "ON" again, the information display shows the same speed limit sign the last time the ignition switch was fumed "OFF" When you drive in the area where unit of velocity is changed, the traffic signs may not be appeared or the different traffic signs may be appeared on the informa­tion display after passing the actual traf­fic signs. This is not a malfunction. The display will be resumed after driving for a while. The speed limit sign on the information display that is higher or lower than the actual limited speed sign may be dis­played for the speed limit sign

Situations where the system does not activate Under the following situations, the system does not activate. When the engine is off When dual sensor brake support indica­tor light and lane departure warning indi­cator light are initially lighting immediately after the ignition switch is in "ON" position For manual transmission vehicle, the gearshift lever is in "R" position, for auto­matic transmission vehicle, the gearshift lever is in "P", "R", or "N" position When the dual sensor is temporarily stopped or malfunctioning When the ESP® OFF switch is pushed and the system is turned off When the traffic sign recognition is turned off by operating the setting mode of information display When parking brake is applied When you drive in the area that there are no speed limit signs and has speed limit
OPERATING YOUR VEHICLE
3-40