To switch to the setting mode 1) Push and hold the information switch (1) when the vehicle is stationary. 2) After the display of setting mode is shown, select the setting item that you want to change by turning the indicator selector knob (2) left or right. Refer to "Setting mode" in this section for details.
NOTE: If you switch to the setting mode while either of the following items is shown on the information display, the current value will be reset. If you do not want to reset its value, push the indicator selector knob (2) quickly beforehand and switch to the other item. Average fuel consumption • Driving time • Average speed
To exit the setting mode 1) To exit the setting mode, select "Back" and push the indicator selector knob (2). 2) Push the information switch (1) quickly.
NOTE: You can exit the setting mode by either of the following operations: Tum the ignition switch to ';,'\CC" or "LOCK" position. • Start driving your vehicle.
Information display
The information display is shown when the ignition switch is in "ON" position.
(A) (B)
(C)
(D) (E) (F)
(G)
(1) Information display
(1)
78RB02033
BEFORE DRIVING
78RB02039
(2) Trip meter selector knob (3) Indicator selector knob
The information display shows the following information.
Display (A) Clock
Display (B) Thermometer
Display (C) Warning and indicator messages I Fuel consumption / Driving range / Average speed / Driving time Display (D) Selector position (for Automatic transmission models)/ Gear position (for Automatic transmission models) / Gearshift indicator (if equipped)
2-28
BEFORE DRIVING
Instantaneous fuel consumption The display shows instantaneous fuel consumption with a bar graph only when the vehicle is moving.
NOTE: The display does not show the bar graph unless the vehicle is moving. Depending on the vehicle's specification, the fuel consumption units of initial setting are indicated as U100km, km/L or MPG (UK). The indicated maximum value of instantaneous fuel consumption is one of the followings. No more than the maximum value will be indicated on the display even if the actual instantaneous fuel consumption is higher. -For U100km setting: 30 -For km/L setting: 50 -For MPG (UK) setting: 80 The indication on the display may be delayed if fuel consumption is greatly affected by driving conditions. The display shows estimated values. Indications may not be the same as actual values.
2-31
Average fuel consumption If you previously selected average fuel consumption setting, the display shows average fuel consumption from the last reset to the present when the ignition switch is turned "ON".
NOTE: When you reconnect the terminals to the lead-acid battery, the value of average fuel consumption will be shown after driving for a period of time.
You can select the timing to reset the value of average fuel consumption by one of the following three methods; Reset after refuel: the value of average fuel consumption will be reset automatically by refueling. Reset with trip meter A: the value of average fuel consumption will be reset automatically by resetting trip meter A. Reset manually: the value of average fuel consumption will be reset by pushing and holding the indicator selector knob (3) when the display indicates the average fuel consumption.
To change the timing to reset the value of average fuel consumption, refer to "Setting mode" in this section.
NOTE: If you add only a small amount of fuel when you select "Reset after refuel", the average fuel consumption value may not be reset.
Driving range If you selected driving range the last time you drove the vehicle, the display indicates "---" for a few seconds and then indicates the current driving range when the ignition switch is turned "ON".
The driving range shown in the display is the approximate distance you can drive until the fuel gauge indicates "E", based on current driving conditions.
When the low fuel warning light comes on, the display "---" will appear.
If the low fuel warning light comes on, fill the fuel tank immediately regardless of the value of driving range shown in the display.
When you refuel, the driving range is updated. However, if you only add a small amount of fuel, the correct value will not be displayed.
BEFORE DRIVING
Setting mode
When the ignition switch is "ON" and the vehicle is stationary, you can enter the setting mode of the information display by pushing and holding the indicator selector knob (3) for a while.
To select the setting that you want to change, turn the indicator selector knob (3) left or right. To change the setting, push the indicator selector knob (3). To exit the setting mode, select "Back" and push the indicator selector knob (3).
78RB02096
NOTE: The currently selected setting item is surrounded by a frame.
2-33
NOTE: If you push and hold the indicator selector knob (3) to enter the setting mode when the display (CJ shows average fuel consumption or average speed, driving time, the value will be reset simultaneously. If you do not want to reset the value, push the indicator selector knob quickly to switch the indication of the display. If you turn the ignition switch or start to move the vehicle when the display is in the setting mode, the setting mode will be canceled automatically.
Distance unit (Odometer I trip meter I driving range I average speed distance unit setting) You can change the units in which odometer I trip meter I driving range I average speed distance is displayed.
Fuel economy (Fuel consumption unit setting) You can change the units that fuel consumption is displayed in.
Language You can change the language of the information display.
Fuel reset (Average fuel consumption reset setting) You can change when the value of average fuel consumption is reset.
Temperature (Temperature unit setting) You can change the units that temperature is displayed in. To change the temperature unit, select "Temperature" in "Setting mode". Then, select "°C" or "°F".
NOTE: When you change the units that temperature is displayed in, the automatic heating and air conditioning system temperature display units will be changed automatically.
Clock setting (Adjusting the clock) • Adjust the clock by selecting "Clock setting" in "Setting mode". Then, select "Adjust clock". To change the hour indication, turn the indicator selector knob (3) left or right repeatedly when the hour indication appears as reversed color. To change the hour indication quickly, turn and hold indicator selector knob (3). To set the hour indication, push the indicator selector knob (3) and the minute indication appears as reversed color. To change the minute indication, turn the indicator selector knob (3) left or right repeatedly when the minute indication appears as reversed color. To change the minute indication quickly, turn and hold indicator selector knob (3). To set the minute indication, push the indicator selector knob (3).
BEFORE DRIVING
ESP® OFF indicator light
57L30045
When the ignition switch is turned "ON", this light comes on briefiy so you can check that the light is working.
When the ESP® OFF switch is pushed to turn off the ESP® systems (other than ABS), the ESP® OFF indicator light comes on and stays on.
For details of the ESP® systems, refer to "Electronic stability program (ESP®)" in "OPERATING YOUR VEHICLE" section.
NOTE: If the vehicle speed is greater than approximately 30 km/h (19 mph}, the ESF'® systems (other than ABS) will be activated automatically and the light will go out. When the transfer lever is in "4L" (4-wheel drive low range) position, the ES?® system (other than ABS) will be canceled automatically. The light will come on and stay on.
2-43
Hill hold control OFF indicator light
(@)
OFF
78RB02086
When the ignition switch is turned "ON", this light comes on briefly so you can check that the light is working. This light comes on when the hill hold control system is deactivated.
For details of the hill hold control system, refer to "Hill hold control system" in the "OPERATING YOUR VEHICLE" section.
Hill descent control indicator light
79K050
When the ignition switch is turned "ON", this light comes on briefiy so you can check that the light is working. When you push the hill descent control switch and the hill descent control operating conditions are fulfilled, the hill descent control indicator comes on. If the hill descent control indicator blinks, the hill descent control will not be activated.
For details of the hill descent control system, refer to "Hill descent control system" in the "OPERATING YOUR VEHICLE" section.
BEFORE DRIVING
Rear passenger's seat belt
reminder light (if equipped)
78RB02087
When the rear passenger does not buckle his or her seat belt, this light will come on and/or blink. For details of the seat belt reminder, refer to "Seat belts and child restraint systems" in this section.
2-45
AIRBAG light
63J030
When the ignition switch is turned "ON", this light comes on for several seconds so you can check that the light is working.
The light will come on and stay on if there is a problem in the airbag system or the seat belt pretensioner system.
A WARNING
If AIRBAG light does not blink or come on briefly when the ignition switch is turned "ON", stays on for more than 10 seconds, or comes on while driving, the airbag system or the seat belt pretensioner system may not work properly, which could result in serious injury in the event of a collision. Have both systems inspected by a SUZUKI dealer.
Malfunction indicator light
65D530
Your vehicle has a computer-controlled emission control system. A malfunction indicator light is provided on the instrument cluster to indicate when it is necessary to have the emission control system serviced. When the ignition switch is turned "ON", this light comes on. When the engine is started, the light goes out.
If the malfunction indicator light comes on or blinks when the engine is running, there is a damage in the emission control system. Bring the vehicle to a SUZUKI dealer to have the damage fixed.
Also, if this light comes on when the engine is running, there is a problem with the automatic transmission system. Ask a SUZUKI dealer to have the system inspected.
Engine coolant temperature light
54G344
When the ignition switch is turned "ON", this light comes on briefly so you can check that the light is working.
This indicator has the following two functions.
Low engine coolant temperature light (blue color)
This light stays on while the engine is still cold and goes off when the engine has warmed up.
If this light blinks, there is a problem with the system. Have your vehicle inspected by a SUZUKI dealer.
High engine coolant temperature warning light (red color)
If this light blinks while driving, it means the engine is running hot. Avoid driving conditions that may lead to actual overheating. If the light stays on without blinking, then the engine is overheating. Follow the instructions in "Engine trouble: Overheating" of "EMERGENCY SERVICE" section.
NOTICE
Continuing to drive the vehicle when engine overheating is indicated can result in severe engine damage.
BEFORE DRIVING
Dual sensor brake support indica
tor light (if equipped)
54P000255
When the ignition switch is turned "ON", this light comes on briefly so you can check that the light is working.
When the automatic brake system is activated, this light blinks rapidly.
In the following situations, this light will come on and the dual sensor brake support will stop functioning when the ignition switch is "ON".
When the dual sensor is faulty, the function of the dual sensor stops until the ignition switch is turned to LOCK position. Find a safe place to park and turn the ignition switch to "LOCK" position. Restart the engine, and check that the dual sensor brake support indicator light, lane departure warning indicator light and high beam assist warning light go off.
2-48
Under the following situations, the function of the dual sensor stops temporarily. When the situations are improved, the temporary stop of the function will be canceled. When the visibility of the dual sensor is poor. When the temperature of the body of dual sensor is high. When the systems related to the dual sensor brake support stops temporarily. When the battery has a voltage abnormality.
For details, refer to "Dual sensor brake support (if equipped)" in the "OPERATING YOUR VEHICLE" section.
Lane departure warning OFF indicator light (if equipped)
62R0317
When the ignition switch is turned "ON", this light comes on briefly so you can check that the light is working.
In the following situations, this light will come on and the lane departure warning and the vehicle swaying warning will stop functioning when the ignition switch is turned "ON". When the lane departure warning OFF switch is pushed to turn off the lane departure warning. When the ESP® OFF switch is pushed to turn off the ESP® systems (other than ABS), the ESP® OFF indicator light will also come on.
For details, refer to "Dual sensor brake support (if equipped)" in "OPERATING YOUR VEHICLE" section.
BEFORE DRIVING
Automatic headlight leveling
system warning light (if equipped)
-to ::::::;
"i'
64J046
When the ignition switch is turned "ON", this light comes on briefly so you can check that the light is working. If this light comes on, there is a problem with the automatic headlight leveling system. Bring the vehicle to a SUZUKI dealer to have the problem corrected.
2-50
Automatic light operation
(if equipped)
(4) (3)
(1) (2)
68PM00228
78RB02093
BEFORE DRIVING
Your vehicle's lighting system is controlled by two main systems: the lighting switch and the auto-on headlight system (when the lighting switch is in "AUTO" position). The two systems work together to operate your lights as shown in the following chart:
ON: Lights ON LIGHT: When it is light around the light sensor (5). DARK: When it is dark around the light sensor (5).
Lighting Ignition switch in the
Main lights to be 11LOCK11 or "ACC" switch posi-operated position tion LIGHT DARK
Position lights, --(1) OFF Tail lights
Headlights --
Position lights, --(2)AUTO Tail lights
Headlights --
Position lights, ON ON (3) :Otlc Tail lights
Headlights --
Position lights, ON ON (4) ,o Tail lights
Headlights ON ON
Ignition switch in the "ON" position
LIGHT DARK
--
--
-ON
-ON
ON ON
--
ON ON
ON ON
2-56