2021 NISSAN GT-R parking brake

.To drive forward, move the shift lever
to the
position.
Starting on level ground or an uphill:
1. Check the shift lever position indicator on the meter to confirm that the
driving gear is selected.
2. Release the parking brake.
3. Release the foot brake pedal gradu- ally, then slowly depress the accelera-
tor pedal to start the vehicle in
motion.
(“R mode start function” page 5-33)
NOTE:
. To prevent the clutch from over-
heating when the parking brake is
applied, engine output is limited
when the accelerator pedal is de-
pressed. In particular, the vehicle
may not start smoothly when the
accelerator pedal is depressed with
the parking brake applied on an
uphill grade. To enable smooth
starting, release the parking brake
before moving the vehicle.
. The hill start assist system operates
when the vehicle is accelerating
from a stop on an uphill. (
“Hill
Start Assist System” page 5-39)
When driving the vehicle
WARNING
Do not move the shift lever to theposition while driving. Doing so may
result in an accident due to loss of
engine braking. It may also damage
the transmission.
Normal driving:
Drive with the shift lever in the
position.
The appropriate gear will be automati-
cally shifted according to the position of
the accelerator pedal, the driving speed
and driving conditions.
Passing:
.
position. This automatically shifts the
transmission into a lower gear and
maintains this position depending on
the gradient of the hill.
. The system may down shift according
to the accelerator pedal position and
the vehicle speed.
. If the transmission is frequently chan-
ging gears while driving, switch to theposition and select the appropriate
gear for the driving conditions.
Driving on a downhill:
.position and 4th or 3rd gear will
provide gentle engine braking.
When driving on a steep downhill, select-
ing the
position and 2nd or 1st gear will
provide powerful engine braking.

When parking the vehicle
position
and stop the engine. If the engine is
running and the shift lever is not in
the
position, the vehicle may start
moving due to partial engagement
of the clutch or to the effects of
gravity on a slope, or the vehicle may
suddenly accelerate due to acciden-
tal operation of the accelerator ped-
al, possibly causing an accident.
For models without NCCB (NISSAN Car-
bon Ceramic Brake) package:
WARNING
Follow the instructions below when
parking the vehicle to help prevent
the brake rotor and brake pads from
rusting together. Failure to follow
the instructions could cause the
rotor and pads to rust together. If
the rotor and pads rust together,
there may be a popping noise and
some vibration when the vehicle is
driven, a wheel may not roll correctly, or the brake pads could be damaged.
If the pads are damaged, this may
reduce the effectiveness of the brake
system which could cause a collision,
serious personal injury or death.
The GT-R uses brake pad materials that
have high metallic content. The brake pad
material helps maintain braking perfor-
mance in a wide range of weather and
driving conditions.
For the first 3,000 miles (5,000 km) of the
vehicle’s service life, and for the first 3,000
miles (5,000km) after a brake replace-
ment, the brake pad to brake rotor
clearance is very small. When parking,
apply the parking brake and move the
shift lever to the
position is selected.
5. Push the ignition switch to stop the engine.
For models with NCCB (NISSAN Carbon
Ceramic Brake) package:
(“NCCB (NISSAN Carbon Ceramic
Brake)” page 8-20)

position. Failure
to do so could cause the vehicle
to move unexpectedly or roll
away and result in an accident.
. Make sure the shift lever has
been pushed as far forward as it
can go and cannot be moved
without depressing the foot
brake pedal.
. Follow the instructions below
when parking the vehicle to help
prevent the brake rotor and
brake pads from rusting to-
gether. Failure to follow the in-
structions could cause the rotor
and pads to rust together. If the
rotor and pads rust together,
there may be a popping noise
and some vibration when the
vehicle is driven, a wheel may
not roll correctly, or the brake
pads could be damaged. If the
pads are damaged, this may re-
duce the effectiveness of the
brake system which could cause
a collision, serious personal injury
or death. (for models without
NCCB (NISSAN Carbon Ceramic
Brake) package)
PARKING/PARKING ON HILLS

position.
3. To help prevent the vehicle from roll- ing into the street when parked on a
sloping drive way, it is a good practice
to turn the wheels as illustrated.
.
HEADED DOWNHILL WITH CURB:Turn the wheels into the curb and
move the vehicle forward until the
curb side wheel gently touches the
curb.
.
HEADED UPHILL WITH CURB:Turn the wheels away from the
curb and move the vehicle back
until the curb side wheel gently
touches the curb.
.
HEADED UPHILL OR DOWNHILL, NO
CURB:Turn the wheels toward the side of
the road so the vehicle will move
away from the center of the road if
it moves.
4. Push the ignition switch to the LOCK position.
For models without NCCB (NISSAN Car-
bon Ceramic Brake) package:
The GT-R uses brake pad materials that
have high metallic content. The brake pad
material helps maintain braking perfor-
mance in a wide range of weather and driving conditions.
For the first 3,000 - 6,000 miles (5,000 -
10,000 km) of the vehicle’s service life, and
for the first 3,000 - 6,000 miles (5,000 -
10,000 km) after a brake replacement, the
brake pad to brake rotor clearance is very
small. When parking, apply the parking
brake and move the shift lever to the
position. Idle the engine for more than 20
seconds without depressing the brake
pedal. This allows the brake pads to move
away from the rotor so the pad does not
contact the rotor.
Additionally, the brakes must be dry
before parking the vehicle after driving
on wet roads or after washing the vehicle.
If the roads are wet, lightly apply the
brakes for a short distance before parking
the vehicle to dry the brakes. After wash-
ing the vehicle, dry the brakes by driving
on a dry road for a few miles and apply
the brakes normally based on traffic and
road conditions.
The metallic brake pads and brake disc
rotor may rust together when the brakes
are not applied:
.
If the vehicle is not idled for 20
seconds without the brakes applied,
or if the brakes are applied when the
vehicle is shut off, the rotor and pads
can rust together, even when the brake pads are dry.
. If the brakes are wet when the vehicle
is parked and the parking brake is
applied for a long time.
It is recommended you contact a GT-R
certified NISSAN dealer if the brake pads
and brake rotor have rusted together.
For models with NCCB (NISSAN Carbon
Ceramic Brake) package:
(
“NCCB (NISSAN Carbon Ceramic
Brake)” page 8-20)
Starting and driving
5-47

, position the two vehicles (
and
) to bring their batteries into
close proximity to each other. Do not
allow the two vehicles to touch.
2. Apply parking brake. Move the shift lever to the
position. Switch off all unnecessary electrical systems (light,
heater, air conditioner, etc.).
3. Remove the battery cover. Cover the battery with a firmly wrung out moist
cloth to reduce explosion hazard.
4. Connect jumper cables in the se- quence as illustrated (
?
?
CAUTION
.Always connect positive (+) to
positive (+) and negative (−) to
body ground (as illustrated), not
to the battery.
. Make sure that the jumper cables
do not touch moving parts in the
engine compartment and that
clamps do not contact any other
metal.
5. Start the engine of the booster vehicle
and let it run for a few minutes.
6. Keep the engine speed of the booster
In case of emergency
6-7

.
NOTE:
Do not keep the starter motor en-
gaged for more than 10 seconds. If
the engine does not start right away,
push the ignition switch to the OFF
position and wait 10 seconds before
trying again.
7. After starting your engine, carefully disconnect the negative cable and
then the positive cable (
?
?“Removing the cowl top cover”
page 8-5) Do not attempt to start the engine by
pushing.
NOTICE
Your NISSAN cannot be push-started
or tow-started. Attempting to do so
may cause transmission damage.
WARNING
.
Do not continue to drive if your
vehicle overheats. Doing so could
cause engine damage or a vehicle
fire.
. To avoid the danger of being
scalded, never remove the radia-
tor filler cap and the coolant
reservoir cap while the engine is
still hot. When the cap is removed,
pressurized hot water will spurt
out, possibly causing serious in-
jury.
. Do not open the hood if steam is
coming out.
If your vehicle is overheating (indicated by
an extremely high temperature gauge
reading), or if you feel a lack of engine
power, detect unusual noise, etc., take the
following steps:
1. Move the vehicle safely off the road, apply the parking brake and move the
shift lever to the
position.
Do not stop the engine.
2. Turn off the air conditioner. Open all the windows, move the temperature
control to maximum hot and fan
PUSH STARTING IF YOUR VEHICLE OVERHEATS

switch is pushed to the OFF position.position, the headlight must be off. Turn
the headlight switch to the
position
for full illumination when driving at night.
If the parking brake is applied before the
engine is started, the daytime running
lights do not illuminate. The daytime
running lights illuminate once the parking
brake is released. The daytime running
lights will remain on until the ignition
switch is pushed to the OFF position or
the headlights turn on.
Turn signal
Move the lever up or down to signal the
turning direction. When the turn is com-
pleted, the turn signals cancel automati-
cally.

position
.
2. Push the ignition switch to the ON position.
3. The autolight system automatically turns the headlights on and off.
To turn the autolight system off, turn the
switch to the
position.
The autolight system can turn on the
headlights automatically when it is dark and turn off the headlights when it is
light.
If the ignition switch is pushed to the ON
position when the parking brake is ap-
plied, the headlights remain off.
With the
position selected, the head-
lights turn off when the ignition switch is
pushed to the OFF position, the shift lever
is placed in the
position or the parking
brake is applied. (The parking, side mar-
ker, tail, license plate, and instrument
lights are on.)
With the AUTO position selected (head-
lights are on), the headlights will remain
on for 45 seconds when the ignition
switch is placed in the OFF position and
one of the doors is opened.
Instruments and controls
2-55