2021 NISSAN GT-R display

USING THE WASHERPull the lever toward you to operate the
washer. Then the wiper will also operate
several times.
NOTE:
When the level of washer fluid is low, a
warning display appears on the vehicle
information display. (
“Low washer
fluid warning” page 2-44)
“Outside mirrors” page 3-28)
REAR WINDOW DEFROSTER SWITCH

OUTSIDE AIR TEMPERATUREThis displays the outside air temperature.
NOTE:
.The outside air temperature may not
be displayed correctly in the follow-
ing cases.
—The outside air temperature is
lower than −22°F (−30°C) or is
higher than 131°F (55°C).
— The vehicle is stopped or is driving
at a low speed (less than approxi-
mately 12 MPH (20 km/h)).
— The temperature in the engine
compartment is high. .
When the outside air temperature is
lower than 37°F (3°C), the low outside
temperature warning will be dis-
played and “ICY” is indicated on the
outside air temperature display.
(
“Alert” page 2-20)Instruments and controls
2-19

SETTING (drive computer)This is used to set the alert, maintenance
and optional settings.
Use the NEXT switch
to select an
item, then confirm with the ENTER switch
to change to the corresponding
setting screen.
To return to the initial setting screen,
push and hold the ENTER switch
for
more than 1 second. NOTE:
.
When the battery terminal is discon-
nected, the set memory will be
erased and the settings return to
the default.
. Setting is not possible in the follow-
ing cases.
—The vehicle is being driven.
— A warning display is active.
— The instrument brightness con-
trol level display is active.
— The cruise control status is dis-
played.
AlertThis function can be used to make
settings for the upshift indicator, “time
to rest” indicator and low outside tem-
perature warning.
Upshift indicator:
For details concerning the upshift indica-
tor, refer to the following section.
(
“Upshift indicator” page 2-10)

to change the time. Push and
hold the switch to increase the number
every 1 hour. A maximum of 6 hours can
be set.
NOTE:
The default setting is OFF.
Low outside temperature warning:
This alert informs the driver when the
outside air temperature is lower than 37°F
(3°C).
On the ICY screen, push the NEXT switch
to turn this warning ON/OFF.
NOTE:
The default setting is ON.
MaintenanceThis function can be used to set the
various maintenance intervals and to
check the engine oil level. The reminders
shown below are used to notify the driver
of the maintenance intervals.
NOTE:
Because these are displayed based on
the mileage driven, they do not indicate
the actual conditions of the vehicle. Use
these functions only as a reference.
Input the maintenance distance using the
following items:
. On each setting screen, push the
Instruments and controls
2-21

GT-R Overview
GTR
Illustrated table of contents
0
Safety — Seats, seat belts and supplemental restraint
systemInstruments and controlsPre-driving checks and adjustmentsDisplay screen, heater, air conditioner and audio systemsStarting and drivingIn case of emergencyAppearance and careDo-it-yourselfMaintenance and schedules
123456789
Technical and consumer information
10
Index
11

Transmission oil:
The reminder is displayed when the
customer set mileage is exceeded. Select
SETTING > MAINTENANCE > OIL > T/M OIL
to set or reset the mileage for the
transmission oil change.
NOTE:
The default setting is 37,000 miles
(60,000 km). The maximum mileage
that can be set is 55,500 miles (90,000
km).
Tires:
This reminder appears when the custo-
mer set distance comes for maintaining
tires. You can set or reset the distance for
maintaining tires. (
“Setting (drive
computer)” page 2-20)

affect tire wear and when tires
should be replaced. Setting the tire
maintenance reminder for a certain
driving distance does not mean your
tires will last that long. Use the tire
maintenance reminder as a guide
only and always perform regular tire
checks. Failure to perform regular
tire checks, including tire pressure
checks could result in tire failure.
Serious vehicle damage could occur
and may lead to a collision, which
could result in serious personal in-
jury or death.
NOTE:
The default setting is OFF.
OptionsThis function can be used to make
settings for language and unit.
Language:
Select ENGLISH or FRANCAIS for use in the
vehicle information display.
Unit:
Select METRIC or US for use in the vehicle
information display.
while a
warning display is active to return to the
original display.
It is also possible to check any warnings
that have not been corrected.
(
“Warning display” page 2-36)
Checking the warningsUse the NEXT switch
to select “DE-
TAIL”, then confirm with the ENTER switch
.
When there are multiple warnings, push

to change the
display among them.
To return to the initial warning, push and
hold the ENTER switchfor more than
1 second.
NOTE:
If there are no warnings to display, only
“SKIP” can be selected.
Instruments and controls
2-25