2021 MERCEDES-BENZ GLB SUV clock

#
Turn tyre sealant bottle 9aqu arter turn
clockwise. #
Insert the plug of /ller hose 3in soc ket5
of tyre sealant bottle 9.#
Turn /ller hose 3aqu arter turn clockwise. #
Remo vetheva lve cap from valve A onthe
fa ulty tyre. #
Screw union nut 4of /ller hose 3onto
va lve A. #
Insert plug 7into a 12 V soc ket in your vehi-
cle. #
Turn theke yto position 1inthe ignition loc k. #
Press on and o. switch 8onthe tyre in0a-
tion compressor.
The tyre in0ation compressor is switched on.
The tyre is in0ated. Firs t, tyre sealant is pum-
ped into the tyre. The pressure may brie0y rise
to appr oximately 500 kPa (5 bar/73 psi).
Do no Do no t switc
t switc h
ho.
o. t
the tyr
he tyr e
ein0ation
in0ation com
compr
pressor
essor
dur
dur ing t
ing t his phase!
his phase! #
Let the tyre in0ation compressor runfo r a
maximum of ten minutes.
The tyre should then ha veattained a tyre pres-
sure of at least 200 kPa (2.0 bar/29 psi).
If tyre sealant leaks out, make sure you clean the
a.ected area as quickly as possible. It is prefera-
ble touse clean water.
If yo uget tyre sealant on your clo thing, ha veit
cleaned as soon as possible with per chloroe thy-
lene.
If,
If, aTer aTer t
ten minut
en minut es, a tyr
es, a tyre pr
e pressur
essur e of 200 kPa
e of 200 kPa
(2.0 bar/29 psi) has no
(2.0 bar/29 psi) has no t been att
t been attained:
ained: #
Switch o. the tyre in0ation compressor. #
Unscr ewthe /lling hose from theva lve of the
defective tyre.
Please no tethat tyre sealant may leak out when
unscr ewing the /lling hose. #
Drive forw ards or in reve rseve ry slo wly for
appr oximately 10 m. #
Pump up the tyre again.
ATer a maximum of ten minutes the tyre pres-
sure must be at least 200 kPa (2.0 bar/
29 psi). &
W WARNING
ARNING Risk of accident due tothe
speci/ed tyre pressure not being attained
If th e speci/ed tyre pressure is not attained
aTer the speci/ed time, the tyre is too badly
damaged. The tyre sealant cannot repair the
tyre in this instance.
The braking and driving characteristics may be
gr eatly impaired. #
Do not continue driving. #
Consult a quali/ed specialist workshop. 334
334
Breakdown assis
tance

The braking and driving
characteristics may be
gr eatly impaired. #
Do not continue driving. #
Consult a quali/ed specialist workshop. Countr
Countr
ies t
ies that hav
hat hav e Mer
e Mercedes-Benz Ser
cedes-Benz Ser vice24h:
vice24h:
yo u will /nd a stic ker with thete lephone number,
e.g. on the B‑pillar on the driver's side. #
Correct the tyre pressure if it is still at least
130 kPa (1.3 bar/19 psi). See the tyre pres-
sure table on the fuel /ller 0ap forva lues.
Incr
Incr easing t
easing t he tyr
he tyre pr
e pressure
essure #
Switch on the tyre in0ation compressor.
Decr
Decr easing t
easing t he tyr
he tyre pr
e pressure
essure #
Remo vethe tyre sealant bottle from the tyre
in0ation compressor. #
Insert the /ller hose in the soc ket of the tyre
in0ation compressor and turn it a quarter turn
clockwise. #
Press pressure release button Cnext to
manome terB.
When t
When t he tyr
he tyre pr
e pressur
essur e is corr
e is corr ect
ect #
Unscr ewthe /lling hose from theva lve of the
sealed tyre. #
Screw theva lve cap onto theva lve of the
sealed tyre. #
Stow the tyre sealant bottle and the tyre in0a-
tion compressor. #
Drive tothe nearest quali/ed specialist work-
shop and ha vethe tyre, tyre sealant bottle and
/lling hose replaced there. Batt
Batt
er
ery (v
y (v ehicle)
ehicle) N
No
ot
tes on t
es on t he 12 V batt
he 12 V batt ery
ery &
W
WARNING
ARNING Risk ofexplosion due toelec-
trostatic charge
Electrostatic charge can ignite the highly
ex plosive gas mixtu reinthe batter y. #
Todischar geany elect rostatic charge
th at may ha vebuilt up, touch the me tal
ve hicle body before handling the batter y. The high
ly0ammable gas mixtu reis created while
th e battery is charging and during starting assis-
ta nce. &
W
WARNI NG
ARNI NGDanger of chemical burns from
th e battery acid
Battery acid is caustic. #
Avoid contact with the skin, eyes or
clo thing. #
Do not lean overth e batter y. #
Do not inhale battery gases. 336
336
Breakdown assis
tance

*
N
NO
OTE
TE Damage totheve hicle from secur-
ing it inco rrectly #
ATer loading, theve hicle must be
secured on all four wheels. Otherwise,
th eve hicle could be damaged. #
A minimum dis tance of 20 cm upwards
and 10 cm down wards must be kept to
th e transport platform. #
Secure theve hicle on all four wheels aTer
loading.
4MA
4MA TIC v
TIC v ehicles/v
ehicles/v ehicles wit
ehicles wit h aut
h automatic tr
omatic tr ans-
ans-
mission
mission #
Make sure that the front and rear axles come
to rest on the same transpor tation vehicle.
* N
NOOTE
TE Damage tothe drive train due to
incor rect positioning of theve hicle #
Do not position theve hicle abo vethe
connection point of the transport vehi-
cle. T
T
o
o wing ey
wing eye st
e st or
orag
ag e location
e location The
towing eye is under the load compartment
0oor. F
F
itting and r
itting and r emo
emoving t
ving t heto
he towing eye
wing eye #
Press the mark on co ver1 inwa rds and
re mo ve. #
Screw intheto wing eye clockwise as far as it
will go and tighten.
V
V ehicles wit
ehicles wit h a tr
h a trailer hitc
ailer hitc h:
h:vehicles with a trailer
hitch do not ha veare ar brac ketfo rth eto wing
ey e. Fasten theto w bar tothe trailer hitch. 344
344
Breakdown assistance

Plas
Plastic hub cap
tic hub cap #
T
To r
o r emov
emov e:
e:turn the centre co ver of the hub
cap anti-clockwise and remo vethe hub cap. #
T To o /t:
/t: make sure that the centre co ver of the
hub cap is turned anti-clockwise. #
Position the hub cap and turn the centre co ver
clockwise until the hub cap engages ph ysically
and audibl y. R
R
aising t
aising t he v
he vehicle when c
ehicle when c hanging a wheel
hanging a wheelR
R
eq
eq uir
uir ements:
ements:
R There are no persons in theve hicle.
R The vehicle has been prepared for a wheel
ch ange (/ page 359).
R The wheel trims and hub caps ha vebeen
re mo ved (/ page 359).
Impor tant no tes on using the jack:
R Use only a vehicle-speci/c jack that has been
appr ovedby Mercedes-Benz toraise theve hi-
cle.
R The jack is only designed forra ising and hold-
ing theve hicle for a short time while a wheel is being
changed and not for maintenance
wo rkunder theve hicle.
R The jack must be placed on a /rm, 0at and
non-slip sur face. If necessar y,use a lar ge, 0at,
load-bearing, non-slip underla y.
R The foot ofthe jack must be positioned verti-
cally under the jack support point. Ru
les of conduct when theve hicle is raised:
R Never place your hands or feet under theve hi-
cle.
R Never lie under theve hicle.
R Do not start theve hicle and do not release the
electric parking brake.
R Do not open or close any doors or theta ilgate. 360 360
Wheels and tyres

#
Position support 2of jack 4on jack sup-
port point 1. #
Turn ratchet 3clockwise until support 2
sits comple tely on jack support point 1and
th e base of the jack lies evenly on thegr ound. #
Turn ratchet 3until the tyre is raised a maxi-
mum of 3 cm from thegr ound. #
Loosen and remo vethe wheel (/ page 362). R
R
emo
emo ving a wheel
ving a wheel R R
eq eq uir
uir ements:
ements:
R The vehicle is raised (/ page 360).
* NO
NOTE
TEMercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. When
changing a wheel, avoid applying any force
to the brake disks, as this could impair the le vel of
comfort when braking.
* N
NOOTE
TE Damage tothre ading from dirt on
wheel bolts #
Do not place wheel bolts in sand or on a
dirty sur face. #
Unscr ewthe uppermost wheel bolt com-
ple tely. #
Screw cent ring pin 1into theth re ad ins tead
of the wheel bolt. #
Unscr ewthere maining wheel bolts com-
ple tely. #
Remo vethe wheel and, if necessar y,store it in
th e load compartment. #
Notes on removing an emer gency spa rewheel
(/ page 364). F F
itting a ne
itting a ne w wheel
w wheel R
R
eq
eq uir
uir ements:
ements:
R The wheel tobe changed is remo ved and the
cent ring pin is sc rewe d in (/ page 362). 362
362
Wheels and tyres

*
N
N O
OTE
TE Mercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. &
W
W ARNING
ARNING Risk of accident from losing a
wheel
Oiled, greased or damaged wheel bolt/wheel
nut thre ads or wheel hub/wheel mounting
bolt thre ads can cause the wheel bolts/wheel
nuts tocome loose.
As a result, you could lose a wheel while driv-
ing. #
Never oil or grease theth re ads. #
Intheev ent of damage totheth re ads,
contact a quali/ed specialist workshop
immediatel y. #
Have the damaged wheel bolts or dam-
aged hub thre ads replaced. #
Do not continue driving. #
Obser vethe information on thech oice of tyres
(/ page 354).
Fo r tyres with a speci/ed direction of rotation, an
ar ro w on the side wall of the tyre indicates the
cor rect direction of rotation. Obser vethe direc-
tion of rotation when /tting. #
Slide the wheel tobe mounted onto the cen-
tring pin and push it on. #
Obser vethe no tes on /tting an emer gency
spa rewheel (/ page 364). &
W
WARNING
ARNING Risk of injury from tightening
wheel bolts and nuts
If yo u tighten the wheel bolts or wheel nuts
when theve hicle is raised, the jack could tip. #
Only tighten wheel bolts or wheel nuts
when theve hicle is on thegr ound. #
Obser vethe inst ructions and saf ety no tes on
"Changing a wheel" (/ page 354). #
For saf etyre asons, only use wheel bolts which
ha ve been appr oved byMercedes-Benz and
fo rth e wheel in question. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated until they are
/nger-tight. #
Unscr ewand remo vethe centring pin. #
Tighten the last wheel bolt until it is /n ger-
tight. #
Lowe rth eve hicle (/ page 363). Low Low
er
ering t
ing t he v
he vehicle
ehicle aTer
aTera wheel c
a wheel c hange
hange R
R
eq
eq uir
uir ements:
ements:
R The new wheel has been /tted (/ page 362). #
T To low o low er t
er the v
he v ehicle:
ehicle: placethera tchet onto
th e he xagon nut of the jack so that the letters
"AB" are visible and turn anti-clockwise. Wheels and tyres
363
363