2021 MERCEDES-BENZ E-CLASS COUPE wheel

#
Always be particular lycareful around the
ta ilpipe and theta ilpipe trims and super-
vise children especially closely in this
area. #
Allow vehicle parts tocool down before
to uching them. To
avo id damage totheve hicle, obser vethe no tes
on cleaning and care of thefo llowing vehicle
parts:
Wheels and r Wheels and r ims
ims
R Use water and acid-free alloy wheel cleaners.
R Do not use acidic alloy wheel cleaners to
re mo vebrake dust. This could damage wheel
bolts and brake components.
R Toavo id cor rosion of the brake disks and
brakepads, drive theve hicle for a few minu tes
aTer cleaning before parking it. The brake
disks and brakepads warm up and dry out.
W
W indo ws
indo ws
R Clean the windo wsinside and outside with a
damp clo thand with a cleaning agent recom-
mended for Mercedes-Benz. R
Do not use dry clo ths or abrasive or sol vent-
based cleaning agents toclean the inside of
windo ws.
% ATer changing the wiper blades or treating
th eve hicle with wax, clean the windscreen
th oroughly with cleaning agents recommen-
ded for Mercedes-Benz. Failure toobser vethe
application instructions may result in damage,
smear mar ksor dazzling spots.
% Remo veextern al fogging or dirt on the wind-
screen in front of the multifunction camera.
Otherwise, driving systems and driving saf ety
systems may be impaired or not available
(/ page 185).
W W iper blades iper blades
R Movethe wiper arms into there placement
position (/ page 136).
R With th e wiper arms folded out, clean the
wiper blades with a damp clo th.
% Make sure that the wiper blades are coated.
The coating can lea veresidues on a clo th. Do
not rubth e wiper blades excessively or clean
th em too oTen. Ext
Ext er
erior lighting
ior lighting
R Clean the lenses with a wet sponge and mild
cleaning agent, e.g. car sha mpoo.
R Only use cleaning agents or cleaning clo ths
th at are suitable for plastic lenses.
Sensors
Sensors
R Clean the sensors in the front and rear bump-
ers with a soT clo thand car shampoo
(/ page 185).
R When using a high-pressure cleaner, main tain
a minimum distance of 30 cm.
Rev
Rev er
ersing camer
sing camer a and 360° Camera
a and 360° Camera
R Open the camera co ver with the multimedia
system (/ page 228).
R Use clean water and a soT clo thtoclean the
camera lens.
R Do not use a high-pressure cleane r.
T
T ailpipes
ailpipes
R Clean with a cleaning agent recommended for
Mercedes-Benz, especially in the winter and
aTer washing theve hicle.
R Do not use acidic cleaning agents. Main
tenance and ca re
313
313

R
Do not use sol vent-based cleaning agents, pol-
ishes or waxes.
R
R oof lining
oof lining
R Clean with a brush or dry shampoo.
Car
Car pet
pet
R Use a carpet and textile cleaning agent recom-
mended for Mercedes-Benz.
St
St eer
eer ing wheel made of g
ing wheel made of g enuine leat
enuine leather or DINA-
her or DINA-
MICA
MICA
* NO
NO TE
TEDamage caused bywrong cleaners #
Do not use sol vent-based cleaning
agents such as tarre mo ver or wheel
cleaner; neither should you use polishes
or wa xes. Otherwise you may damage
th e /nish. R
Clean with a damp clo thand 1% soapy water
solution and then wipe with a dry clo th.
R For heavy soiling: Use a cleaner recommen-
ded for Mercedes-Benz.
R Leather care: Use a leather care agent that
has been recommended for Mercedes-Benz. R
Do not allow the leather tobecome too damp.
R Do not use a micro/bre clo th.
% Leather is a natural product. It has natural
surface properties, such as di.erences in
st ru cture, mar kscaused bygrow thand injury
or subtle colour di.erences. These sur face
properties are characteristics of leather and
not material faults. What's more, leather is
subject toa natural ageing process during
which the sur face properties change.
Genuine leat Genuine leat her seat cov
her seat covers
ers
R Clean with a damp clo thand then wipe with a
dry clo th.
R Leather care: Use a leather care agent that
has been recommended for Mercedes-Benz.
R Do not allow the leather tobecome too damp.
R Do not use a micro/bre clo th.
% Regular cleaning and care ofthe leather
re duces soiling, wear mar ksand ageing dam-
age and thus signi/cant lyex tends its life
span. Clo thing that can lea vestains, e.g.
jeans, can le ave discolouration on the leather. DIN
DINAMIC AMIC A seat cov
A seat cov ers
ers
R Clean with a damp clo th.
R Do not use a micro/bre clo th.
Imit
Imit ation leat
ation leat her seat cov
her seat cov ers
ers
R Clean with a damp clo thand 1% soapy water.
R Do not use a micro/bre clo th.
F
F abr
abr ic seat cov
ic seat cov ers
ers
R Clean with a damp micro/bre clo thand 1%
soapy water and allow todry. Maintenance and ca
re
315
315

#
LeT-hand
LeT-hand dr
driv
ive v
e v ehicle:
ehicle: pulltab1 upwards. #
Right-hand dr
Right-hand dr iv
ive v
e v ehicle:
ehicle: pulltab1 down-
wa rds. #
Remo ve/re extinguisher 2. Flat tyre
Flat tyre
N
No
ot
tes on
es on 0at
0attyr
tyr es
es &
W
WARNING
ARNING Risk of accident due toa 0at
tyre
A 0at tyre se verely a.ects the driving charac-
te ristics as well as the steering and braking of
th eve hicle. T
T
yr
yr es wit
es wit hout
houtr
run-0at
un-0at c
char
har act
acter
eristics:
istics: #
Do not drive with a 0at tyre. #
Change the 0at tyre immediately with an
emer gency spa rewheel or spare wheel.
Alternativel y,consult a quali/ed special-
ist workshop.
T
T yr
yr es wit
es wit h
hr
run-0at
un-0at c
char
har act
acter
eris
istics:
tics: #
Obser vethe information and warning
no tes on MOExtended tyres (run-0at
tyres). In
theev ent of a 0at tyre, thefo llowing options are
av ailable depending on your vehicle's equipment:
R V
Vehicles wit
ehicles with MOExt h MOExtended tyr
ended tyr es:
es:it is possible
to continue the journey for a short period of
time. Make sure you obser vethe no tes on
MOExtended tyres (run-0at tyres)
(/ page 318).
R V Vehicles wit
ehicles wit h a TIREFIT kit:
h a TIREFIT kit: you can repair the
tyre so that it is possible tocontinue the jour-
ney for a short period of time. Todo this, use
th e TIREFIT kit (/ page 320). R
V
Vehicles wit
ehicles wit h Mer
h Mercedes me connect:
cedes me connect: you can
make a call for breakdown assistance via the
ove rhead control panel in the case of a break-
down (/ page 281).
R All v
All v ehicles:
ehicles: change the wheel (/ page 347). N
No
ot
tes on MOExt
es on MOExt ended tyr
ended tyres
es(r
(run-0at
un-0at tyr
tyres)
es) &
W
WARNING
ARNING Risk of accident when driving in
limp-home mode
Driving in emer gency mode impai rsthe han-
dling characteristics of theve hicle. #
Do not exceed the permissible maximum
speed of the MOExtended tyres. #
Avoid any abrupt steering and driving
manoeuvres as well as driving over
obstacles (kerbs, pot holes, o.-road).
This applies, in particular, toa loaded
ve hicle. #
Stop driving in the emer gency mode if
yo u notice:
R banging noise 318 318
Breakdown assistance

At
a dis tance of app roximately 1 m tothe tyre
in0ation compressor and appr oximately 1.6 m
abo vethegr ound, thefo llowing sound pres-
sure le vels appl y:
R Emission sound pressure le vel L
PA 83 dB
(A)
R Sound po wer le vel L
WA 91 dB (A)
The tyre in0ation compressor is maintenance-
free. If there is a malfunction, please contact
a qu ali/ed specialist workshop. Using t Using t
he TIREFIT kit
he TIREFIT kit R
R
eq
eq uir
uir ements:
ements:
R Tyre sealant bottle and tyre in0ation compres-
sor (/ page 319)
R TIREFIT stic ker
R Gloves
Yo u can use TIREFIT tyre sealant toseal per fora-
tion damage of up to4 mm, particular lythose in
th e tyre contact sur face. You can use TIREFIT in
outside temp eratures down to-20 °C. &
W
WARNING
ARNING Risk of accident when using
tyre sealant
The tyre sealant may be unable toseal the
tyre proper ly, especially in thefo llowing cases:
R there are lar gecuts or punctures in the
tyre (la rger than damage pr eviously men-
tioned)
R the wheel rims ha vebeen damaged
R aTer journe yswith very low tyre pressure
or with 0at tyres #
Do not continue driving. #
Consult a quali/ed specialist workshop. &
W
WARNING
ARNING Risk of injury and poisoning
from tyre sealant
Ty re sealant is hazardous tohealth and causes
ir rita tion. Do not allow it tocome into contact
with your skin, eyes or clo thing, and do not
swallow it. Do not inhale any vapours. Keep
th e tyre sealant away from children. Obser
vethefo llowing if you come into contact
with the tyre sealant: #
Rinse o. the tyre sealant from your skin
using water immediatel y. #
If tyre sealant gets into your eyes, thor-
oughly rinse them using clean water
immediatel y. #
If tyre sealant has been swallo wed,thor-
oughly rinse out your mouth immediately
and drink plenty of water. Do not induce
vo miting and seek medical attention
immediatel y. #
Change out of clo thing which has come
into contact with tyre sealant immedi-
atel y. #
If an alle rgic reaction occurs, seek medi-
cal attention immediatel y. *
N NO
OTE
TE Overheating due tothe tyre in0ation
compressor running too long #
Do not runth e tyre in0ation compressor
fo r longer than ten minutes without inter-
ru ption. 320 320
Breakdown assistance

Comply with
the manufacturer's saf ety no tes on
th e stic ker on the tyre in0ation compressor.
Ha ve the tyre sealant bottle replaced in a quali/ed
specialist workshop every /ve years. #
Do not remo veany fore ign objects which ha ve
entered the tyre. #
A1x part 1ofthe TIREFIT stic kerto the
inst rument clus ter within the driver's /eld of
vision. #
A1x part 2ofthe TIREFIT stic ker near the
va lve on the wheel with the defective tyre. #
Pull plug 4with the cable and hose 5out
of the tyre in0ation compressor housing. #
Push the plug of hose 5into 0an ge6 of
tyre sealant bottle 1until the plug engages. #
Place tyre sealant bottle 1head down wards
into recess 2ofthe tyre in0ation compres-
sor. #
Remo vetheva lve cap from valve 7 onthe
fa ulty tyre. #
Screw /lling hose 8onto valve 7. #
Insert plug 4into a 12 V soc ket in your vehi-
cle. #
Switch on theve hicle. #
Switch on the tyre in0ation compressor using
On/O. switch 3.
The tyre is in0ated. Firs t, tyre sealant is pum-
ped into the tyre. The pressure may brie0y rise
to appr oximately 500 kPa (5.0 bar/73 psi).
Do no
Do no t switc
t switc h
ho.
o. t
the tyr
he tyr e
ein0ation
in0ation com
compr
pressor
essor
dur
dur ing t
ing t his phase!
his phase! Breakdown assistance
321
321

T
T
o
o w
w -st
-st ar
ar ting or to
ting or towing away
wing away P
P
er
er mitt
mitt edto
ed towing met
wing met hods (non plug-in h
hods (non plug-in h ybr
ybrid)
id) *
N
NO OTE
TE Damage from automatic braking If one of
thefo llowing functions is switched
on, theve hicle brakes automatically in cer tain
situations:
R Active Brake Assist
R Active Distance Assist DISTRONIC
R HOLD function
R Active Parking Assist
To avoid damage totheve hicle, deactivate
th ese systems in thefo llowing or similar situa-
tions: #
during towing #
in a car wash Mercedes-Benz
recommends transporting your
ve hicle in the case of a breakdown, rather than
to wing it away.
Fo rto wing, use a tow rope or tow bar with bo th
axles on thegr ound. Do not use tow bar systems. *
N
NO OTE
TE Damage totheve hicle due to tow-
ing awa y incor rectly #
Obser vethe inst ructions and no tes on
to wing away. V
V
ehicles wit
ehicles wit h r
h rear wheel dr
ear wheel dr ive
ive P
P
er
er mitt
mitt edto
ed towing met
wing met hods
hods
Bo th axles on
th egr ound Ye
s, maximum 50 km at
50 km/h
Fr ont axle
ra ised No
Re ar axle
ra ised Ye
s, if the steering wheel is
/xed in the centre position
with a steering wheel lock 4MA
4MA
TIC v
TIC v ehicles
ehicles P
P
er
er mitt
mitt edto
ed towing met
wing met hods
hods
Bo th axles on
th egr ound Ye
s, maximum 50 km at
50 km/h
Fr ont axle
ra ised No
Re ar axle
ra ised No T
T
o
o wing wit
wing wit h a r
h a raised axle:
aised axle: towing should be per-
fo rm ed byato wing compan y. T
T
o
o wing t
wing t he v
he vehicle wit
ehicle wit h bot
h both axles on t
h axles on t hegr
he ground
ound #
Obser vethe no tes on the permitted towing
me thods (/ page 329). #
Make sure that the battery is connected and
ch arge d.
Obser vethefo llowing points when the battery is
dischar ged:
R the engine cannot be star ted Breakd
own assistance
329
329

&
W
W ARNI NG
ARNI NGRisk of accident due tolimited
saf ety-re lated functions during theto wing
process
Saf ety-re lated functions are limited or no lon-
ge rav ailable in thefo llowing situations:
R theve hicle is switched o..
R the brake system or po wer steering system
is malfunctioning.
R the energy supply or the on-board electri-
cal system is malfunctioning.
When your vehicle is towe daw ay, signi/cantly
more e.ort may be requ ired tosteer and
brake than is normally requ ired. #
Use a tow bar. #
Make sure that the steering wheel can
mo vefreely be fore towing theve hicle
awa y. *
N
NO
OTE
TE Damage due toexcessive tractive
po wer If
yo u pull away sharpl y,the tractive po wer
may be too high and theve hicles could be
damaged. #
Pull away slo wlyand smoo thly. Loading t
Loading t
he v
he vehicle f
ehicle f or tr
or transport
anspo rt #
Obser vethe no tes on towing away
( / page 329). #
Connect theto wing device totheto wing eye
in order toload theve hicle.
% You can also attach theto w bar tothe trailer
hitch. #
V
Vehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: shiTthe
automatic transmission toposition i.
% V
Vehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: the
automatic transmission may be loc ked in posi-
tion jintheev ent of damage tothe electri-
cal system. ToshiT toi , pr ovide the on- board electrical system with po
wer
( / page 327). #
Load theve hicle onto the transpor ter. #
V
Vehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: shiTthe
automatic transmission toposition j. #
Use the electric parking brake tosecure the
ve hicle against rolling away. #
Only secure theve hicle bythe wheels.
V
V ehicles wit
ehicles wit h ADS PL
h ADS PLUS (A
US (Adap
daptiv
tive Dam
e Dam ping Sy
ping Sy s-
s-
t
t em PL
em PL US)
US) &
W
WARNING
ARNING Risk of an accident when trans-
porting vehicles with Adaptive Damping
System PLUS
When transpo rting vehicles with Adaptive
Damping System PLUS, theve hicle/trailer
combination may begin torock and start to
skid. #
Load theve hicle cor rectly onto the
transpor ter. #
Secure theve hicle on all four wheels
with suitable tensioning straps. Breakdown assistance
331
331

#
Do not exceed the maximum permissible
speed of 60 km/h when transporting. *
N
NOOTE
TE Damage totheve hicle from secur-
ing it inco rrectly #
ATer loading, theve hicle must be
secured on all four wheels. Otherwise,
th eve hicle could be damaged. #
A minimum dis tance of 20 cm upwards
and 10 cm down wards must be kept to
th e transport platform. #
Secure theve hicle on all four wheels aTer
loading. 4MA
4MA
TIC v
TIC v ehicles/v
ehicles/v ehicles wit
ehicles wit h aut
h automatic tr
omatic tr ans-
ans-
mission
mission #
Make sure that the front and rear axles come
to rest on the same transpor tation vehicle.
* N
NOOTE
TE Damage tothe drive train due to
incor rect positioning of theve hicle #
Do not position theve hicle abo vethe
connection point of the transport vehi-
cle. T
T
o
o wing eye
wing eye To
wing eye1 is attached tothe edge of the boot
under the boot 0oor. 332
332
Breakdown assistance