2021 MERCEDES-BENZ CLA COUPE wheel

Ru
les of conduct when theve hicle is raised:
R Never place your hands or feet under theve hi-
cle.
R Never lie under theve hicle.
R Do not start theve hicle and do not release the
electric parking brake.
R Do not open or close any doors or the boot
lid. #
Using the wheel wrench, loosen the wheel
bolts on the wheel you wish tochange by
about one full turn. Do not unscr ewthe
scr ews comple tely. Po
sition of jack support points
* N
NOOTE
TE Mercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. &
W
WARNING
ARNING Risk of injury from incor rect
positioning of the jack
If yo u do not position the jack cor rectly at the
appropriate jacking point of theve hicle, the
jack could tip wi th theve hicle raised. #
Only position the jack at the appropriate
jacking point of theve hicle. The base of th
e jack must be positioned vertically
under the jacking point of theve hicle. *
N
NOOTE
TE Vehicle damage from the jack If
yo u do not position the jack cor rectly at the
appropriate jack support point of theve hicle,
th e jack could tip over with theve hicle raised. #
The jack is designed exclusively for jac k-
ing up theve hicle at the jack support
points. #
Take thera tchet out of the tyre-change tool kit
and place it on the he xagon nut of the jack so
th at the letters "AUF" are visible. Wheels and tyres
377
377

#
Position support 2of jack 4on jack sup-
port point 1.
% Ifth ere is a tota l loss of pressure in a tyre, it
may be possible that the jack cannot be posi-
tioned at jack support point 1. Inthis case,
unload theve hicle. #
Turn ratchet 3clockwise until support 2
sits comple tely on jack support point 1and
th e base of the jack lies evenly on thegr ound. #
Turn ratchet 3until the tyre is raised a maxi-
mum of 3 cm from thegr ound. #
Loosen and remo vethe wheel (/ page 378). R
R
emo
emo ving a wheel
ving a wheel R
R
eq
eq uir
uir ements:
ements:
R The vehicle is raised (/ page 376).
* NO
NOTE
TEMercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. When
changing a wheel, avoid applying any force
to the brake discs, as this could impair the le vel of
comfort when braking. *
N
NOOTE
TE Damage tothre ading from dirt on
wheel bolts #
Do not place wheel bolts in sand or on a
dirty sur face. #
Unscr ewthe uppermost wheel bolt com-
ple tely. #
Screw cent ring pin 1into theth re ad ins tead
of the wheel bolt. #
Unscr ewthere maining wheel bolts com-
ple tely. #
Remo vethe wheel. 378 378
Wheels and tyres

F
F
itting a ne
itting a ne w wheel
w wheel R R
eq eq uir
uir ements:
ements:
R The wheel tobe changed is remo ved and the
cent ring pin is sc rewe d in (/ page 378).
* NO
NOTE
TEMercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. &
W
W ARNING
ARNING Risk of accident from losing a
wheel
Oiled, greased or damaged wheel bolt/wheel
nut thre ads or wheel hub/wheel mounting
bolt thre ads can cause the wheel bolts/wheel
nuts tocome loose.
As a result, you could lose a wheel while driv-
ing. #
Never oil or grease theth re ads. #
Intheev ent of damage totheth re ads,
contact a quali/ed specialist workshop
immediatel y. #
Have the damaged wheel bolts or dam-
aged hub thre ads replaced. #
Do not continue driving. #
Obser vethe information on thech oice of tyres
(/ page 370).
Fo r tyres with a speci/ed direction of rotation, an
ar ro w on the side wall of the tyre indicates the
cor rect direction of rotation. Obser vethe direc-
tion of rotation when /tting. #
Slide the wheel tobe mounted onto the cen-
tring pin and push it on. &
W
WARNING
ARNING Risk of injury from tightening
wheel bolts and nuts
If yo u tighten the wheel bolts or wheel nuts
when theve hicle is raised, the jack could tip. #
Only tighten wheel bolts or wheel nuts
when theve hicle is on thegr ound. #
Be sure toobser vethe inst ructions and saf ety
no tes on "Changing a wheel" (/ page 370). #
For saf etyre asons, only use wheel bolts which
ha ve been appr oved byMercedes-Benz and
fo rth e wheel in question. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated until they are
/nger-tight. #
Unscr ewand remo vethe centring pin. #
Tighten the last wheel bolt until it is /n ger-
tight. #
Lowe rth eve hicle (/ page 379). Low Low
er
ering t
ing t he v
he vehicle
ehicle aTer
aTera wheel c
a wheel c hange
hange R
R
eq
eq uir
uir ements:
ements:
R The new wheel has been /tted (/ page 379). #
T To low o low er t
er the v
he v ehicle:
ehicle: placethera tchet onto
th e he xagon nut of the jack so that the letters
"AB" are visible and turn anti-clockwise. Wheels and tyres
379
379

#
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
an initial maximum forc e of 80 Nm. #
Tighten the wheel bolts evenly in a diagonal
pattern in the order indicated 1to5 with
th e speci/ed tightening torque of 130 Nm. &
W
WARNING
ARNING Risk of accident due toincor-
re ct tightening torque
The wheels could come loose if the wheel
bolts or wheel nuts are not tightened tothe
prescribed torque. #
Ensure that the wheel bolts or wheel
nuts are tightened tothe prescribed
tightening torque. #
Ifyo u are not sure, do not mo vetheve hi-
cle. Con tact a quali/ed specialist work-
shop and ha vethe tightening torque
ch ecked immediatel y. #
Check the tyre pressure of the ne wly/tted
wheel and adjust it if necessar y.
% The following does not apply if the new wheel
is an emer gency spa rewheel. #
V
V ehicles wit
ehicles wit h tyr
h tyre pr
e pr essur
essur e loss w
e loss w ar
arning sy
ning sy s-
s-
t
t em:
em: restart the tyre pressure loss warning
system (/ page 370). #
V
V ehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e monit
e monit or
oring sy
ing sy s-
s-
t
t em:
em: restart the tyre pressure monitoring sys-
te m (/ page 369). Emerg
Emerg
ency spar
ency spar e wheel
e wheel N
No
ot
tes on t
es on t he emerg
he emerg ency spar
ency spar e wheel
e wheel &
W
WARNING
ARNING Risk of accident caused by
incor rect wheel and tyre dimensions
The wheel or tyre size and the tyre type of the
emer gency spa rewheel or spare wheel and
th e wheel tobe replaced may di.er. The emer-
ge ncy spa rewheel or spare wheel can signi/-
cantly impair driving characteristics of the
ve hicle.
To prev ent hazardous situations: #
Drive carefull y. #
Never /t more than one emer gency
spa rewheel or spare wheel that di.ers
in size. #
Only use an emer gency spa rewheel or
spare wheel brie0y. #
Do not deacti vate ESP ®
. #
Have the emer gency spa rewheel or
spare wheel of a di.erent size replaced
at the nearest quali/ed specialist work- 380
380
Wheels and tyres

shop. The new wheel must ha
vethe cor-
re ct dimensions. %
The emer gency spa rewheel is secured in the
emer gency spa rewheel bag in the boot.
Obser vethefo llowing no tes on /tting an emer-
ge ncy spa rewheel:
R The maximum permissible speed with an
emer gency spa rewheel /tted is 80 km/h.
R Do not /t the emer gency spa rewheel with
snow chains.
R Replace the emer gency spa rewheel aTer six
ye ars at the latest, rega rdless of wear.
R Check the tyre pressure of the emer gency
spa rewheel /tted. Cor rect the pressure as
necessar y.
% The speci/ed tyre pressure is stated on the
label of the emer gency spa rewheel.
% V
V ehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e loss w
e loss w ar
arning
ning
syst
syst em:
em: if an emer gency spa rewheel is /tted,
th e tyre pressure loss warning system cannot
function reliabl y.Only restart the system again when
the emer gency spa rewheel has
been replaced with a new wheel.
V
V ehicles wit
ehicles wit h a tyr
h a tyre pr
e pressur
essur e monit
e monit or
oring sy
ing sy s-
s-
t
t em:
em: if an emer gency spa rewheel is /tted, the
tyre pressure monitoring system cannot func-
tion reliabl y.Fo r a few minutes aTer an emer-
ge ncy spa rewheel is /tted, the system may
still display the tyre pressure of there mo ved
wheel. Only restart the system again when the
emer gency spa rewheel has been replaced
with a new wheel.
Be sure toalso obser vethefo llowing fur ther rela-
te d subjects:
R Notes on tyre pressure (/ page 366)
R Tyre pressure table (/ page 367)
R Notes on /tting tyres (/ page 370)
R Fitting an emer gency spa rewheel
(/ page 375) In0ating In0ating
t
the emerg
he emerg ency spar
ency spar e wheel
e wheel *
N
NOOTE
TE Overheating due tothe tyre in0ation
compressor running too long #
Do not runth e tyre in0ation compressor
fo r longer than ten minutes without inter-
ru ption. R
R
eq
eq uir
uir ements:
ements:
Comply with the manufacturer's saf ety no tes on
th e stic ker of the emer gency spa rewheel and on
th e tyre in0ation compressor. #
Remo vethe stic ker with the label 80 km/h
from the tyre in0ation compressor housing
and a1x it tothe inst rument clus ter within the
driver's /eld of vision. #
Remo vethe tyre in0ation compressor from the
st ow age well under the boot 0oor
(/ page 346). Wheels and tyres
381
381

#
Pull /ller hose 1and plug 3out of the tyre
in0ation compressor housing. #
Insert plug 7of /ller hose 1inthe soc ket
on the tyre in0ation compressor and then turn
it until plug 7engages. #
Unscr ewthe cap from theva lve on the emer-
ge ncy spa rewheel. #
Screw union nut 2of /ller hose 1onto the
va lve. #
Make sure on and o. switch 4ofthe tyre
in0ation compressor is set to 00. #
Insert plug 3in a soc ket in your vehicle.
R Cigar ette lighter soc ket R
12 V soc ket (/ page 125)
R Obser vethe no tes on the cigar ette lighter in
th e Digital Owner's Manual
R Obser vethe no tes on soc kets (/ page 125). #
Press the start/s top button once toswitch on
th e po wer supply (/ page 159). #
Press on and o. switch 4onthe tyre in0a-
tion compressor to II.
The tyre in0a tion compressor is switched on.
The tyre is in0ated. The tyre pressure is shown
on manom eter 5. #
Pump the tyre tothe speci/ed tyre pressure.
% The speci/ed tyre pressure is stated on the
label of the emer gency spa rewheel. #
When the speci/ed tyre pressure has been
re ached, press on and o. switch 4onthe
tyre in0ation compressor to 00.
The tyre in0a tion compressor is switched o.. #
Press the start/s top button toswitch o. the
po we r suppl y. #
Ifth e tyre pressure is higher than the speci/ed
pressure, press pressure release valve button 6
until the cor rect tyre pressure has been
re ached. #
Unscr ewunion nut 2of /ller hose 1from
th eva lve. #
Screw theva lve cap of the emer gency spa re
wheel onto theva lve again. #
Stow /ller hose 1and plug 3inthe lo wer
section of the tyre in0ation compressor hous-
ing. #
Stow the tyre in0ation compressor in theve hi-
cle. 382 382
Wheels and tyres

Fo
rth e cor rect mixing ratio, referto the informa-
tion on the antifreeze container.
Mix washer 0uid with windscreen washer 0uid all
ye ar round. V
V
ehicle data
ehicle data V
V
ehicle dimensions
ehicle dimensions The heights speci/ed may
vary as a result of the
fo llowing factors:
R tyres
R load
R condition of the suspension
R optional equipment
N
No ot f
t f or plug-in h
or plug-in h ybr
ybrid:
id:
V
V ehicle dimensions
ehicle dimensions All models
All models
Ve
hicle lengt h4 688 mm
Ve hicle width including outside
mir rors 1999 mm All models All models
Ve
hicle width excluding out-
side mir rors 1830 mm
Ve hicle height 1444 mm
Wheelbase 2729 mm V V
ehicle dimensions (plug-in h ehicle dimensions (plug-in h ybr
ybrid)
id) CL CL
A 250 e A 250 e
Ve hicle lengt h4 688 mm
Ve hicle width including outside
mir rors 1999 mm
Ve hicle width excluding outside
mir rors 1830 mm
Ve hicle height 1450 mm
Wheelbase 2729 mm W
W
eights and loads
eights and loads Please obser
vethefo llowing no tesfo rth e speci-
/ed vehicle data:
R Items of optional equipment increase the unla-
den weight and reduce the pa yload.
R Vehicle-speci/c weight information can be
fo und on theve hicle identi/cation plate
(/ page 386).
R
R oof load
oof load Model
Model
Maximum r
Maximum roof load
oof load
All model s1 00 kg High-v
High-v
olt
oltag
age batt
e batt er
ery (plug-in h
y (plug-in h ybr
ybrid)
id) N
No
ot
tes on t
es on t he pow
he pow er suppl
er suppl y f
y for v
or v ehicles wit
ehicles wit h a
h a
high-v
high-v olt
oltag
age batt
e batt ery
ery
In accordance with European standard
EN 17186:2019 vehicle identi/ers are located on
th eve hicle in thefo llowing places:
R Onthe inside of the soc ket 0ap
R Onthech arging cable connector Te
ch nical data
397 397

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences andM
MSolutions
Solutions
Ù
Steering malfunction See
Owner's Manual *T
he elect ric steering lock is malfunctioning. The steering may be loc kedby the electric steering loc k. &
W WARNI NG
ARNI NGRisk of accident if steering capability is impai red
If th e steering does not function as intended, theve hicle's operating saf ety is jeopardised. #
Pull over and stop theve hicle safely as soon as possible, paying attention toroad and tra1c conditions. Do
not continue driving under any circums tances. #
Consult a quali/ed speciali stwo rkshop. #
Stop theve hicle immediately in accordance with the tra1c conditions. Do not continue driving. #
Consult a quali/ed specialist workshop.
û
Before starting the engine,
turn the steering wheel. *T
he elect ric steering lock could not unlock the steering. #
Switch o. theve hicle. #
Tounlock the steering, mo vethe steering wheel slightly tothe leT and right. #
Switch on theve hicle again.
Active bonnet malfunction
See Owner's Manual *T
he active bonn et(pedest rian pr otection) is malfunctioning or inoperative aTer having already been triggered. #
Consult a quali/ed specialist workshop. Displ
aymessages and warning/indicator lamps
425 425