L = Suitable for particular child restraints given on attached list. These restraints may be of the “specific vehicle”,
“restricted” or “semi-universal” categories.
IL = Suitable for particular ISOFIX child restraint system s (CRS) given in the attached list. These ISOFIX CRS are
those of the “specific vehicle”, “restr icted” or “semi-universal” categories.
i-U = Suitable for i-Size “universal” Child Res traint Systems forward and rearward facing.
i-UF = Suitable for forward-facing i-Size “universal” Child Restraint Systems only.
Yes = Child-restraint system can be secured on the seat.
No = Child-restraint system cannot be secured on the seat, or there is no fixture.
X = Child-restraint system cannot be installed.
*1 Vehicles with the seat height adjustment function. (V ehicles without the seat height adjustment function are
indicated by an “X”, and a child-restraint system cannot be installed.)
A Mazda genuine child-restraint system can be installed. Regarding child-restraint systems which can be installed,
refer to the accessories catalog.
(Except Mexico)
Regarding child-restraint systems which can be installed to your Mazda, consult an
Authorized Mazda Dealer.
It is not able to set the child-restraint syst em with the support leg in the rear center seat.
For the CRS which do not carry the ISO/XX si ze class identification (A to G), for the
applicable mass group, the child seat manufacturer shall indicate the vehicle specific
LATCH child-restraint systems recommended for each position.
Essential Safety Equipment
Child Restraint
2-39
CX-3_8JL1-EA-20G_Edition1_old 2020-5-22 15:31:00
ItemFeatureFactory Set
‐
ting Available Settings Settings
Change
Method
Fuel economy resetting
procedure Linkage/non-linkage with fuel
economy reset and trip meter
reset
Off
On/Off B ―
Active Driving Display (page 4-18)
Display Setting can be changed so that
the Active Driving Display is
not displayed.
On On/Off C
―
The display height (up/down
position) can be changed. 013 steps up/down
from initial setting (total: 27 steps) C
―
The method for adjusting the
display brightness (automatical ‐
ly/manually) can be changed. Auto Auto/Man. C
―
The standard brightness while
automatic adjustment is select‐
ed can be changed using the
brightness adjustment. 0
2 steps up/down from
initial setting (total: 5 steps) C
―
The standard brightness while
manual adjustment is selected
can be changed using the
brightness adjustment. 0
20 steps up/down
from initial setting (total: 41 steps) C
―
Navigation guidance Display/non-display OnOn/Off C ―
*1 Though these systems can be turned Off, doing so will defeat the purpose of the system and Mazda
recommends that these systems remain On.
*2 For vehicles with an audio system other than the on-screen function type, the warning sound cannot be changed. The warning sound is only a beep.
*3 Only the volume of the warning beep during Blind Spot Monitoring (BSM) operation can be changed. The volume of the warning beep during Rear Cross Traffic Alert (RCTA) operation cannot be changed.
*4 This system functions only when the navigation system is functioning.*5 If the auto-wiper control is set to Off, the wiper lever position is set to intermittent operation.*6 If the setting is changed to Off, the following opera tion is performed according to the headlight switch
position:
At position: Headlights turn off immediately after the ignition is switched off.At any position other than : Headlights do not turn off after the ignition is switched off.*7 When set to Off, the lights-on reminder is operable.*8 The setting of the lights-on reminder can be changed with the time setting of auto headlight off function set to Off.
Refer to Lights-On Reminder on page 7-42.
*9 The operation may stop in 15 minutes due to the effect of the outside temperature even if the operation time of
the rear window defogger has been changed to Continuous.
*10 Available only in display from the center display.
Specifications
Personalization Features
9-13
CX-3_8JL1-EA-20G_Edition1_old 2020-5-22 15:31:00
