2021 KIA STINGER display

Driving your vehicle
116 5
If the speed of the vehicle is over
40 mph (64 km/h) and the system
detects lane markers, the color
changes from gray to white.When the conditions below are met,
LKA system will be enabled to assist
steering.
Vehicle speed is above 40 mph (64
km/h).
Both lane markers are detected by
LKA system.
The vehicle is between the lane
markers.
If LKA system can assist steering, a
green steering wheel indicator will
illuminate.
Warning
If the vehicle leaves a lane, the
lane marker you cross will blink on
the LCD display.
OCK057116L
OCK057117L
OCK057118L
OCK057119L

5121
Driving your vehicle
LKA system fail indicator
LKA system fail indicator (yellow) will
illuminate with an audible warning if
LKA system is not working properly.
In this case, have the system
checked by an authorized Kia dealer.When there is a problem with the sys-
tem do one of the following:
Turn the system on after turning
the engine off and on again.
Check if the ignition switch is in the
ON position.
Check if the system is affected by
the weather. (ex: fog, heavy rain,
etc.)
Check if there is foreign matter on
the camera lens
If the problem is not solved, have the
system checked by an authorized
Kia dealer.
LKA system Function Change
The driver can change LKA to Lane
Departure Warning (LDW) system or
change LKA system mode between
Standard LKA and Active LKA from
the User Settings Mode on the LCD
display.
The driver can choose them by plac-
ing the ignition switch to the ON posi-
tion and by selecting ‘User Settings’,
‘Driver Assistance’, and ‘Lane
Keeping Assist’.
The system is automatically set to
Standard LKA.

Driving your vehicle
126 5
Second stage alert
The second stage alarm will activate
when:
1.The first stage alert is on
2.The turn signal is on to change a
lane
When the second stage alert is acti-
vated, a warning light will blink on the
outside rearview mirror and an alarm
will sound.
If you move the turn signal switch to
the original position, the second
stage alert will be deactivated.- The second stage alarm can be
deactivated.
To activate the alarm:
Go to the User Settings Mode →
Driver Assistance and select
"Blind-Spot Collision Warning
Sound" on the LCD display.
To deactivate the alarm:
Go to the User Settings Mode →
Driver Assistance and deselect
"Blind-Spot Collision Warning
Sound" on the LCD display.
✽ ✽

NOTICE
The alarm function helps alert the
driver. Deactivate this function only
when it is necessary
Detecting sensor
The sensors are located inside of the
rear bumper.
Always keep the rear bumper clean
for the system to work properly.
OCK057051L
OUM054029
2nd stage

Driving your vehicle
132 5
Driver Attention Warning (DAW) sys-
tem is designed to warn the driver of
potentially hazardous driving situa-
tions if it detects inattentive driving
practices.System setting and activation
System setting
Driver Attention Warning system is
set in the OFF position when your
vehicle is first delivered to you from
the factory.
To turn ON Driver Attention
Warning system, turn on the
engine, and then select 'User
Settings →Driver Assistance →
Driver Attention Warning →
Normal/Early' on the LCD display. The driver can select Driver
Attention Warning system mode.
- Off : Driver Attention Warning
system is deactivated.
- Normal : Driver Attention Warning
system alerts the driver of his/her
fatigue level or inattentive driving
practices.
- Early : Driver Attention Warning
system alerts the driver of his/her
fatigue level or inattentive driving
practices faster than Normal
mode.
The set-up of Driver Attention
Warning system will be maintained
when the engine is re-started.
DRIVER ATTENTION WARNING (DAW) SYSTEM (IF EQUIPPED)

5133
Driving your vehicle
Display of the driver's attention
level
The driver can monitor their driving
conditions on the LCD display.- Select 'User Settings Mode' and
then 'Driver Assistance' on the
LCD display. (For more informa-
tion, refer to "LCD Display" in
chapter 4.)
The driver's attention level is dis-
played on the scale of 1 to 5. The
lower the number is, the more inat-
tentive the driver is.
The number decreases when the
driver does not take a break for a
certain period of time.
The number increases when the
driver attentively drives for a cer-
tain period of time.
When the driver turns on the sys-
tem while driving, it displays 'Last
Break time'.
Take a break
The "Consider taking a break"
message appears on the LCD dis-
play and a warning sounds to sug-
gest that the driver take a break
when the driver's attention level is
below 1.
Driver Attention Warning system
will not suggest a break when the
total driving time is shorter than 10
minutes.
OCK057137L
OCK057138L
OCK057139L

Driving your vehicle
134 5
Resetting the system
The last break time is set to 00:00
and the driver's attention level is
set to 5 (very attentive) when the
driver resets Driver Attention
Warning system.
Driver Attention Warning system
resets in the following situations.- The engine is turned OFF.
- The driver unfastens the seat belt
and then opens the driver’s door.
- The driver takes a break from
driving that lasts more than 10
minutes.
The driver attention warning sys-
tem operates again, when the driv-
er restarts driving.
System disabled
Driver Attention Warning system
enters the ready status and displays
the 'Disabled' screen in the following
situations.
- The camera sensor is unable to
detect the lanes.
- Driving speed remains under 37
mph (60 km/h) or over 112 mph
(180 km/h).
OCK057140L

What to do in an emergency
8 6
TIRE PRESSURE MONITORING SYSTEM (TPMS)
(1) Low tire pressure telltale/
TPMS malfunction indicator
(2) Low tire pressure position telltale
(Shown on the LCD display)
Check tire pressure
You can check the tire pressure in
the information mode on the clus-
ter.
- Refer to “User settings mode” in
chapter 4.
Tire pressure is displayed 1~2 min-
utes later after driving.
If tire pressure is not displayed
when the vehicle is stopped, “Drive
to display” message displays. After
driving, check the tire pressure.
You can change the tire pressure
unit in the user settings mode on
the cluster.
- psi, kpa, bar (Refer to “User set-
tings mode” in chapter 4).
✽ ✽
NOTICE
• The tire pressure may change due
to factors such as parking condi-
tion, driving style, and altitude
above sea level.
• Low tire pressure warning may
sound when a tire’s pressure unit is
equal or higher than nearby tires.
This is a normal occurrence, which
is due to the change in tire pressure
along with tire temperature.
• The tire pressure shown on the
dashboard may differ from the
tire pressure measured by tire
pressure gauge.
OCK067005N
OCK067025L

627
What to do in an emergency
8. Pressure gauge for displaying the
tire inflation pressure
9. Button for reducing tire inflation
pressure
Connectors and cable are stored in
the compressor housing.
✽ ✽
NOTICE
The sealant container and insert
hose (3) cannot be reused. Purchase
an extra after use.
Using the Tire Mobility Kit
1. Detach the speed restriction label
(1) from the sealant bottle (2), and
place it in a highly visible place
inside the vehicle such as on the
steering wheel to remind the driv-
er not to drive too fast.
2. Filling the sealant Strictly follow
the specified sequence, otherwise
the sealant may escape under
high pressure.
OCK068022N
CAUTION
Before using the Tire Mobility
Kit, please read carefully the
instruction attached on the
sealant case. Detach the speed
limit label on the sealant case
and put it on a highly visible
place. Always drive within the
speed limit.
WARNING- Expired
sealant
Do not use the tire sealant after
the sealant has expired (after
the expiration date on the
sealant container). This can
increase the risk of tire failure.
WARNING- Sealant
Keep out of reach of children.
Avoid contact with eyes.
Do not swallow.