Page 343 of 428
SERVICING AND MAINTENANCE
SC \b \fED SERVICING
Your vehicle is equipped with an automatic oil
change indicator system. The oil change indicator
system will remind you that it is time to take your
vehicle in for scheduled maintenance.
Based on engine operation conditions, the oil
change indicator message will illuminate. This
means that service is required for your vehicle.
Operating conditions such as frequent short-trips,
trailer tow, extremely hot or cold ambient
temperatures, and extended idling will influence
when the “Oil Change Required” message is
displayed. Have your vehicle serviced as soon as
possible, within the next 500 miles (805 kmyf .An authorized dealer will reset the oil change
indicator message after completing the scheduled
oil change or for engine oil life reset procedure
Ú
page 110.
NOTE:Under no circumstances should oil change
intervals exceed 10,000 miles (16,000 kmyf R U
12 months, whichever comes first. The engine
controller also monitors the number of hours of
engine run time, and will illuminate the oil change
indicator after 350 hours (which is not likely to be
exceeded except for certain fleet customers with
extended engine idling periodsyf . Once A Month Or Before A Long Trip:
Check engine oil level
Check windshield washer fluid level
Check the tire inflation pressures and look for
unusual wear or damage
Check the fluid levels of the coolant reservoir,
brake master cylinder and fill as needed.
Check function of all interior and exterior lights
8
22_WS_OM_EN_USC_t.book Page 341
Page 361 of 428
W $ 5N ,N *
5 L G L Qg t Ke b Uake V Fa Q Oea G to b Uake Ia L O X Ue a Q G
So V V Lb O \ a Fo O O L V Lo Q. ' U L Y L Qg Z Lt K \o X U Ioot Ue Vt L Qg
o U U L G L Qg o Q t Ke b Uake Se Ga O Fa Q Ue V X Ot L Q
ab Qo U Pa O O \ K Lg K b Uake te P Se Uat X Ue V e [ Fe V V L Ye
O L Q L Qg Zea U a Q G So V V Lb Oe b Uake Ga Page.
Zo X O G Qot Ka Ye \o X U I X O O b Uak L Qg Fa Sa F Lt \ L Q a Q
e Pe Uge Q F \.
W $ 5N ,N *
Use only manufacturer's recommended brake
fluid Úpage 409. Using the wrong type of
brake fluid can severely damage your brake
system and/or impair its performance. The
proper type of brake fluid for your vehicle is
also identified on the original factory installed
hydraulic master cylinder reservoir.
To avoid contamination from foreign matter or
moisture, use only new brake fluid or fluid that
has been in a tightly closed container. Keep
the master cylinder reservoir cap secured at
all times. Brake fluid in a open container
absorbs moisture from the air resulting in a
lower boiling point. This may cause it to boil
unexpectedly during hard or prolonged
braking, resulting in sudden brake failure. This
could result in a collision.
Overfilling the brake fluid reservoir can result
in spilling brake fluid on hot engine parts,
causing the brake fluid to catch fire. Brake
fluid can also damage painted and vinyl
surfaces, care should be taken to avoid its
contact with these surfaces.
WARNING!
8
22_WS_OM_EN_USC_t.book Page 359
Page 405 of 428
TEC \b \f SPECIFICATIONS
VE \b \fE IDENTIFICATION NUMBER (VIN)
The VIN is found on a label located on the left front
corner of the instrument panel pad, visible from
outside of the vehicle through the windshield.
Windshield VIN Label Location
NOTE:It is illegal to remove or alter the VIN.
BRAKE SYSTEM
Your vehicle is equipped with dual hydraulic brake
systems. If either of the two hydraulic systems lose
normal capability, the remaining system will still
function. However, there will be some loss of
overall braking effectiveness. You may notice
increased pedal travel during application, greater
pedal force required to slow or stop, and potential
activation of the Brake Warning Light.
In the event power assist is lost for any reason the
brakes will still function. However, the effort
required to brake the vehicle will be much greater
than that required with the power system
operating.
W \b \f AND TIRE TORQUE SPECIFICATIONS
Proper lug nut/bolt torque is very important to
ensure that the wheel is properly mounted to the
vehicle. Any time a wheel has been removed and
reinstalled on the vehicle, the lug nuts/bolts
should be torqued using a properly calibrated
torque wrench using a six sided (hexyf G H H S Z D O O
socket.
TORQUE SPECIFICATIONS
**Use only authorized dealer recommended lug
nuts/bolts and clean or remove any dirt or oil
before tightening.
Inspect the wheel mounting surface prior to
mounting the tire and remove any corrosion or
loose particles.
Wheel Mounting Surface
Lug Nut/Bolt
Torque **Lug Nut/
Bolt SizeLug Nut/Bolt
Socket Size
130 ft-lb
(176 N·myf M14 x 1.50 22 mm
9
22_WS_OM_EN_USC_t.book Page 403