2021 JEEP PATRIOT wheel

Using The Deflation Button
Push the Deflation Button (2) to reduce
the air pressure in the tire if it becomes
over-inflated.
Tire Service Kit Usage Precautions
•Replace the Tire Service Kit Sealant Bottle
(1) and Sealant Hose (6) prior to the expira-
tion date (printed at the lower right hand
corner on the bottle label) to assure optimum
operation of the system. Refer to “Sealing a
Tire with Tire Service Kit” section (F) “Sealant
Bottle and Hose Replacement”.•The Sealant Bottle (1) and Sealant Hose (6)
are a one tire application use and need to be
replaced after each use. Always replace
these components immediately at your origi-
nal equipment vehicle dealer.
•When the Tire Service Kit sealant is in a
liquid form, clean water, and a damp cloth will
remove the material from the vehicle or tire
and wheel components. Once the sealant
dries, it can easily be peeled off and properly
discarded.
•For optimum performance, make sure the
valve stem on the wheel is free of debris
before connecting the Tire Service Kit.
•You can use the Tire Service Kit air pump to
inflate bicycle tires. The kit also comes with
two needles, located in the Accessory Stor-
age Compartment (on the bottom of the air
pump) for inflating sport balls, rafts, or similar
inflatable items. However, use only the Air
Pump Hose (7) and make sure the Mode
Select Knob (5) is in the Air Mode when
inflating such items to avoid injecting sealant
into them. The Tire Service Kit Sealant is onlyintended to seal punctures less than 1/4 inch
(6 mm) diameter in the tread of your vehicle.
•Do not lift or carry the Tire Service Kit by the
hoses.WARNING!
•Do not attempt to seal a tire on the side of
the vehicle closest to traffic. Pull far
enough off the road to avoid the danger of
being hit when using the Tire Service Kit.
•Do not use Tire Service Kit or drive the
vehicle under the following circumstances:
•If the puncture in the tire tread is ap-
proximately 1/4 inch (6 mm) or larger.
•If the tire has any sidewall damage.
•If the tire has any damage from driving
with extremely low tire pressure.
•If the tire has any damage from driving
on a flat tire.
•If the wheel has any damage.
•If you are unsure of the condition of the
tire or the wheel.
(Continued)Tire Service Kit Expiration Date Location
236

WARNING!(Continued)
•Keep Tire Service Kit away from open
flames or heat source.
•A loose Tire Service Kit thrown forward in a
collision or hard stop could endanger the
occupants of the vehicle. Always stow the
Tire Service Kit in the place provided.
Failure to follow these warnings can result
in injuries that are serious or fatal to you,
your passengers, and others around you.
•Take care not to allow the contents of Tire
Service Kit to come in contact with hair,
eyes, or clothing. Tire Service Kit sealant is
harmful if inhaled, swallowed, or absorbed
through the skin. It causes skin, eye, and
respiratory irritation. Flush immediately
with plenty of water if there is any contact
with eyes or skin. Change clothing as soon
as possible, if there is any contact with
clothing.
(Continued)
WARNING!(Continued)
•Tire Service Kit Sealant solution contains
latex. In case of an allergic reaction or
rash, consult a physician immediately.
Keep Tire Service Kit out of reach of
children. If swallowed, rinse mouth imme-
diately with plenty of water and drink plenty
of water. Do not induce vomiting! Consult a
physician immediately.
Sealing A Tire With Tire Service Kit
(A) Whenever You Stop To Use Tire Service
Kit:
1. Pull over to a safe location and turn on the
vehicle’s Hazard Warning flashers.
2. Verify that the valve stem (on the wheel with
the deflated tire) is in a position that is near
to the ground. This will allow the Tire Service
Kit Hoses (6) and (7) to reach the valve stem
and keep the Tire Service Kit flat on the
ground. This will provide the best positioning
of the kit when injecting the sealant into thedeflated tire and running the air pump. Move
the vehicle as necessary to place the valve
stem in this position before proceeding.
3. Place the transmission in PARK (auto trans-
mission) or in Gear (manual transmission)
and place the ignition in the OFF position.
4. Set the parking brake.
(B) Setting Up To Use Tire Service Kit:
1. Push in the Mode Select Knob (5) and turn to
the Sealant Mode position.
2. Uncoil the Sealant Hose (6) and then re-
move the cap from the fitting at the end of the
hose.
3. Place the Tire Service Kit flat on the ground
next to the deflated tire.
4. Remove the cap from the valve stem and
then screw the fitting at the end of the
Sealant Hose (6) onto the valve stem.
5. Uncoil the Power Plug (8) and insert the plug
into the vehicle’s 12 Volt power outlet.
237

WARNING!(Continued)
the battery to explode and could result in
personal injury. Only use the specific ground
point, do not use any other exposed metal
parts.
5. Start the engine in the vehicle that has the
booster battery, let the engine idle a few
minutes, and then start the engine in the
vehicle with the discharged battery.
6. Once the engine is started, remove the
jumper cables in the reverse sequence:
Disconnecting The Jumper Cables
1. Disconnect the negative(-)end of the
jumper cable from the engine ground of the
vehicle with the discharged battery.
2. Disconnect the opposite end of the negative
(-)jumper cable from the negative(-)post of
the booster battery.3. Disconnect the positive(+)end of the jumper
cable from the positive(+)post of the
booster battery.
4. Disconnect the opposite end of the positive
(+)jumper cable from the positive(+)post of
the vehicle with the discharged battery.
5. Reinstall the air intake duct.
If frequent jump-starting is required to start your
vehicle you should have the battery and charg-
ing system inspected at your authorized dealer.
CAUTION!
Accessories plugged into the vehicle power
outlets draw power from the vehicle’s bat-
tery, even when not in use (i.e., cellular
devices, etc.). Eventually, if plugged in long
enough without engine operation, the vehi-
cle’s battery will discharge sufficiently to de-
grade battery life and/or prevent the engine
from starting.
FREEING A STUCK VEHICLE
If your vehicle becomes stuck in mud, sand or
snow, it can often be moved using a rocking
motion. Turn the steering wheel right and left to
clear the area around the front wheels. Then
shift back and forth between DRIVE and RE-
VERSE (with automatic transmission) or 2nd
gear and REVERSE (with manual transmis-
sion), while gently pressing the accelerator. Use
the least amount of accelerator pedal pressure
that will maintain the rocking motion, without
spinning the wheels, or racing the engine.
CAUTION!
Racing the engine or spinning the wheels
may lead to transmission overheating and
failure. Allow the engine to idle with the
transmission in NEUTRAL for at least one
minute after every five rocking-motion
cycles. This will minimize overheating and
reduce the risk of clutch or transmission
failure during prolonged efforts to free a
stuck vehicle.
243

NOTE:
Push theESC Offswitch, to place the
Electronic Stability Control (ESC) system in
Partial Offmode, before rocking the ve-
hicle. Refer to “Electronic Brake Control” in
“Starting And Operating” for further infor-
mation. Once the vehicle has been freed,
push theESC Offswitch again to restore
ESC Onmode.
CAUTION!
•
When “rocking” a stuck vehicle by shifting
between DRIVE/2nd gear and REVERSE,
do not spin the wheels faster than 15 mph
(24 km/h), or drivetrain damage may result.
•Revving the engine or spinning the wheels
too fast may lead to transmission over-
heating and failure. It can also damage the
tires. Do not spin the wheels above
30 mph (48 km/h) while in gear (no trans-
mission shifting occurring).
WARNING!
Fast spinning tires can be dangerous.
Forces generated by excessive wheel
speeds may cause damage, or even failure,
of the axle and tires. A tire could explode and
injure someone. Do not spin your vehicle’s
wheels faster than 30 mph (48 km/h) or for
longer than 30 seconds continuously without
stopping when you are stuck and do not let
anyone near a spinning wheel, no matter
what the speed.
GEAR SELECTOR OVERRIDE
If a malfunction occurs and the gear selector
cannot be moved out of the PARK position, you
can use the following procedure to temporarily
move the gear selector:
1. Turn the engine OFF.
2. Firmly apply the parking brake.3. Using a small screwdriver or similar tool,
remove the gear selector override access
cover (located on the right side of the gear
selector housing).
4. Turn the ignition switch to the ACC or ON/
RUN position, but do not start the engine.
5. Press and maintain firm pressure on the
brake pedal.
6. Insert the screwdriver or similar tool into the
access port, and push and hold the override
release lever forward.Gear Selector Override Access Cover
244

TOWING A DISABLED
VEHICLE
This section describes procedures for towing a
disabled vehicle using a commercial towing
service.
Towing ConditionWheels OFF the
GroundManual
Transmission6-Speed Automatic
(FWD Only)6-Speed Automatic
4WDCVT Automatic
Transmission
Flat Tow NONE
•Transmission in
NEUTRAL
•Key in ACC or
ON/RUN position
If transmission is
operable:
•Transmission in
NEUTRAL
•Key in ACC or
ON/RUN position
•25 mph (40 km/h)
maxspeed
•15 miles (24 km)
maxdistance
If transmission is
operable:
•Transmission in
NEUTRAL
•Key in ACC or
ON/RUN position
•25 mph (40 km/h)
maxspeed
•15 miles (24 km)
maxdistance
NOT ALLOWED
Wheel Lift or Dolly
To wRearNOT ALLOWED NOT ALLOWED NOT ALLOWED
Front FWD ModelsONLY OK NOT ALLOWEDFWD ModelsONLY
FlatbedALL BEST METHOD BEST METHOD BEST METHOD BEST METHOD
247

With Ignition Key
Automatic Transmission
•Front Wheel Drive (FWD) vehicles can be
towed with the front wheels elevated, or on a
flatbed truck (all four wheelsOFFthe
ground).
•Four-Wheel Drive (4WD) vehicles can be
towed on a flatbed truck (all four wheelsOFF
the ground).
If the transmission is operable, Front Wheel
Drive (FWD) and Four Wheel Drive (4WD)
vehicles, with the 6-speed automatic transmis-
sion only (NOTthe Continuously Variable auto-
matic transmission [CVT]), may be flat towed
(with all four wheels on the ground) under the
following conditions:
•The transmission must be in NEUTRAL.
•The key must be in the ACC or ON/RUN
position.
•The towing speed must not exceed 25 mph
(40 km/h).
•The towing distance must not exceed 15
miles (24 km).Front Wheel Drive (FWD) models (with 6-speed
automaticonly) may also be towed (under the
same limitations shown above) with the rear
wheels elevated.
CAUTION!
DO NOT flat tow any vehicle equipped with a
CVT automatic transmission. Damage to the
drivetrain will result. If these vehicles require
towing, make sure all drive wheels are OFF
the ground.
Towing this vehicle in violation of the above
requirements can cause severe transmission
and/or transfer case damage. Damage from
improper towing is not covered under the
New Vehicle Limited Warranty..
If the vehicle’s battery is discharged, refer to
“Gear Selector Override” in this section for
instructions on shifting the automatic transmis-
sion out of PARK for towing.Manual Transmission
•Front Wheel Drive (FWD) or Four-Wheel
Drive (4WD) vehicles can be flat towed (all
four wheels on the ground) with the transmis-
sion in NEUTRAL and the key in the ACC or
ON/RUN position.
•FWD vehicles can be towed with the front
wheels elevated.
•FWD or 4WD vehicles can be towed on a
flatbed truck (all wheelsOFFthe ground).
CAUTION!
•DO NOTflat tow any disabled vehicle if
condition is related to the clutch, transmis-
sion or driveline. Additional damage to the
drivetrain could result.
•
Towing this vehicle in violation of the above
requirements can cause severe engine,
transmission, or drivetrain damage. Damage
from improper towing is not covered under
the New Vehicle Limited Warranty.
248

paired as soon as possible. The cost of such
repairs is considered the responsibility of the
owner.
•If you carry special cargo such as chemicals,
fertilizers, de-icer salt, etc., be sure that such
materials are well packaged and sealed.
•If a lot of driving is done on gravel roads,
consider mud or stone shields behind each
wheel.
•Use MOPAR Touch Up Paint on scratches as
soon as possible. Your authorized dealer has
touch up paint to match the color of your
vehicle.
Wheel And Wheel Trim Care
•All wheels and wheel trim, especially alumi-
num and chrome plated wheels, should be
cleaned regularly with a mild soap and water
to prevent corrosion.
•To remove heavy soil and/or excessive brake
dust, use MOPAR Wheel Cleaner.NOTE:
If your vehicle is equipped with Dark Vapor
or Black Satin Chrome wheels DO NOT USE
wheel cleaners, abrasives or polishing com-
pounds. They will permanently damage this
finish and such damage is not covered by
the New Vehicle Limited Warranty. USE
ONLY MILD SOAP AND WATER WITH A
SOFT CLOTH. Used on a regular basis this is
all that is required to maintain this finish.
CAUTION!
Do not use scouring pads, steel wool, a
bristle brush, or metal polishes. Do not use
oven cleaner. These products may damage
the wheel’s protective finish. Avoid automatic
car washes that use acidic solutions or harsh
brushes that may damage the wheel’s pro-
tective finish. Only MOPAR Wheel Cleaner
or equivalent is recommended.Stain Repel Fabric Cleaning Procedure —
If Equipped
Stain Repel seats may be cleaned in the follow-
ing manner:
•Remove as much of the stain as possible by
blotting with a clean, dry towel.
•Blot any remaining stain with a clean, damp
towel.
•For tough stains, apply MOPAR Total Clean,
or a mild soap solution to a clean, damp cloth
and remove stain. Use a fresh, damp towel to
remove soap residue.
•For grease stains, apply MOPAR Multi-
Purpose Cleaner to a clean, damp cloth and
remove stain. Use a fresh, damp towel to
remove soap residue.
•Do not use any harsh solvents or any other
form of protectants on Stain Repel products.
Interior Care
Use MOPAR Total Clean to clean fabric uphol-
stery and carpeting.
272

Mileage or time passed
(whichever comes first)
7,500
15,000
22,500
30,000
37,500
45,000
52,500
60,000
67,500
75,000
82,500
90,000
97,500
105,000
112,500
120,000
127,500
135,000
142,500
150,000
Or Months: 12 24 36 48 60 72 84 96 108 120 132 144 156 168 180 192 204 216 228 240
Or Kilometers:
12,000
24,000
36,000
48,000
60,000
72,000
84,000
96,000
108,000
120,000
132,000
144,000
156,000
168,000
180,000
192,000
204,000
216,000
228,000
240,000
Adjust parking brake on ve-
hicles equipped with four-
wheel disc brakes.XX X X X
Replace engine air cleaner
filter.XX X X X
Replace air conditioning/
cabin air filter.XXX X X X X X X X
Replace spark plugs (2.0L &
2.4L Engines) *XX X X X X
Replace spark plugs (2.0L
E22 Engine) *XX
Replace accessory drive
belt(s).X
287