2021 INFINITI QX80 ignition

7
REMOTE ENGINE START (IF SO EQUIPPED)
The remote engine start system must be enabled in the vehicle settings within the lower display. To start your
vehicle remotely:
1. Press the lock button to lock the vehicle.
2. Press and hold the remote engine start button within 5 seconds of pressing the lock button and the
engine will start.
To start driving, depress the brake pedal and push the ignition switch START/STOP button to the ON position.
State laws may apply, review local laws before using.
LOCKING AND UNLOCKING THE VEHICLE
• The lock and unlock operating range of the Intelligent Key is within 31.5 in (80 cm) from each request switch.
• To lock the vehicle, push either door handle request switch once or press the lock button on the key fob.
• To unlock the vehicle, perform one of the following procedures:
• Push either door handle request switch once; the corresponding door will unlock. Push the door handle
request switch again within 60 seconds; all other doors will unlock, or
• Press the unlock button on the key fob to unlock the driver’s side door. Press the unlock button again;
all other doors will unlock.Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.
Infiniti Intelligent Key System

8
• To slide the seat forward or backward, push the switch forward or backward.
• To recline the seatback, push the switch forward or backward.
SEAT LIFTER
• To adjust the angle of the front portion or height of the seat, push the front or rear end of the switch up or down.
LUMBAR SUPPORT
• Push each side of the adjusting switch to adjust the seat lumbar area until the desired position is achieved.
SEAT/STEERING POSITIONING ON EXIT
• The shift lever must be in P (PARK) position with the ignition switch in the OFF position.
• The entry/exit function can be activated by pushing SET switch , located on the driver’s side door, and then
the corresponding seat switch .
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.
Seat Adjustments

11
To complete HomeLink® programing, you can download the HomeLink app or read the
instructions below.
Before you start programing HomeLink
®, park outside and within range of your garage.
Then, clear the area around your garage door, place the ignition switch in the ON or
ACC position and locate the remote control transmitter, ensuring a fresh battery is
installed. Please note, a ladder and secondary person may be needed.
To program HomeLink:
1. Position the handheld transceiver within 3 in (8 cm) from the HomeLink surface.
2. Press and hold the desired HomeLink and garage door opener button. Release both when the indicator
flashes rapidly (if so equipped) or “TRAINED” (if so equipped) is displayed in the status area of the mirror.
Before proceeding to the next steps, be sure your garage door is not moving.
• Press the HomeLink button for 2 seconds up to 3 times. If the garage door responds, training is complete.
If the garage door doesn’t respond:
• Press the “learn” or “set” button on the garage opener until an indicator illuminates. Within 30 seconds, press the
HomeLink button
in your vehicle for 2 seconds up to 3 times.
If the garage door doesn’t respond, please see your owner’s manual, go to www.HomeLink.com/infiniti or call 1-800-355-3515.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.
HomeLink® Garage Door Opener

25
Around View® Monitor with Moving Object Detection
• With the ignition switch in the ON position, activate the Intelligent Around View® Monitor by pressing
the
CAMERA button , located on the control panel, or by moving the shift lever to the
R (Reverse) position. The monitor displays various views of the position of the vehicle.
MOVING OBJECT DETECTION (MOD) (if so equipped)
• The MOD system helps inform the driver of moving objects around the vehicle.
• The system will operate when the shift lever is in the D (Drive), N (Neutral), R (Reverse) or P (Park)
position and the vehicle is driven at speeds of approximately 5 mph (8 km/h) or less.
• If the MOD system detects moving objects, a yellow frame will be displayed on the camera image.
• When the following is displayed:
• Green MOD icon ; the system is active.
• White MOD icon; the system is not active.
• No MOD icon; the system is off. The indicator will also be off if all of the warning systems are
deactivated using the Settings menu.
• The MOD system will not operate if the liftgate is open.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.