2021 INFINITI Q60 COUPE ECU

Red light Name Page
Brake warning light 2-13
Charge warning light 2-13
Master warning light 2-14
Seat belt warning light and
chime2-14
Security indicator light 2-14
Supplemental air bag warn-
ing light2-14Yellow
lightName Page
Anti-lock Braking System
(ABS) warning light2-15
Forward Emergency Braking
(FEB) system warning light (if
so equipped)2-15
Front passenger air bag sta-
tus light2-15
Low fuel warning light 2-15
Low tire pressure warning
light2-15
Malfunction Indicator Light
(MIL)2-17
Master warning light 2-18
Power steering warning light 2-18
Vehicle Dynamic Control
(VDC) off indicator light2-19
Vehicle Dynamic Control
(VDC) warning light2-19Other
lightName Page
ECO drive indicator light 2-19
Exterior light indicator 2-19
Front fog light indicator light 2-19
High beam assist indicator
light (if so equipped)2-19
High beam indicator light 2-19
Turn signal/hazard indicator
lights2-19
Illustrated table of contents0-11
WARNING AND INDICATOR LIGHTS

1-6Safety — Seats, seat belts and supplemental restraint system
WARNING
When returning the seat to its original
position, confirm the seat and seatback
are locked properly.
CAUTION
.Be careful not to pinch your hand or
foot or bump your head when oper-
ating the walk-in seat.
.While operating the walk-in seat, do
not operate the seatback reclining
switch. The reclining motor may be
damaged.
.Do not place any objects near the
seatback of the front seats. They may
be pinched and damaged.
The automatic forwarding and reversing will
not work or stop under the following condi-
tions:
.When the vehicle speed is moving (dri-
ver’s seat only).
.When the seat belt is fastened.
.When the shift lever is not in the P (Park)
position (driver’s seat only)..When the door is closed (automatic
forwarding only).
.While the memory seat (if so equipped)
operates.
.When the memory seat switches (if so
equipped) are pushed.
.When the seatback switch is pushed.
.When the seat position is adjusted.
Note that the seat must be moved to the
front-most position by operating the walk-
in function after the battery is disconnected.
Otherwise, the seat will not move backward
during the walk-in function.
REAR SEATS
Folding
WARNING
.Never allow anyone to ride in the
trunk or on the rear seat when it is in
the fold-down position. Use of these
areas by passengers without proper
restraints could result in serious in-
jury in an accident or sudden stop.
.Properly secure all cargo with ropes
or straps to help prevent it from
sliding or shifting. Do not place cargo
higher than the seatback. In a sudden
stop or collision, unsecured cargocould cause personal injury.
.When returning the seatback to the
upright position, be certain they are
completely secured in the latched
position. If they are not completely
secured, passengers may be injured in
an accident or sudden stop.
.Closely supervise children when they
are around cars to prevent them from
playing and becoming locked in the
trunk where they could be seriously
injured. Keep the car locked, with the
rear seatback and trunk lid securely
latched when not in use, and prevent
children’s access to car keys.

JVR0498X
The rear seatback can be folded according to
the following procedure.
Before folding the seatback:
Remove drink containers from the rear cup
holder.To fold the seatback:
1. Open the trunk lid.
2. Pull the strap located on the left side of
the trunk. The rear seatback will be
unlatched.
3. Fold the rear seatback down.
To return the seatback:
1. Fold up the rear seatback.
2. Securely lock the seatback in position.
WARNING
Head restraint/headrest supplement the
other vehicle safety systems. They may
provide additional protection against
injury in certain rear end collisions.
Adjustable head restraint/headrest
must be adjusted properly, as specified
in this section. Check the adjustment
after someone else uses the seat. Do not
attach anything to the head restraint/
headrest stalks or remove the head
restraint/headrest. Do not use the seat
if the head restraint/headrest has been
removed. If the head restraint/headrest
was removed, reinstall and properly
adjust the head restraint/headrest be-
fore an occupant uses the seating posi-
tion. Failure to follow these instructions
can reduce the effectiveness of the head
restraint/headrest. This may increase
the risk of serious injury or death in a
collision.
Safety — Seats, seat belts and supplemental restraint system1-7
HEAD RESTRAINTS/HEADRESTS

1-8Safety — Seats, seat belts and supplemental restraint system
JVR0388X
The illustration shows the seating positions
equipped with head restraint/headrest.
Indicates the seating position is
equipped with a head restraint.
Indicates the seating position is
equipped with a headrest.
+ Indicates the seating position is not
equipped with a head restraint or headrest.
.Your vehicle is equipped with a head
restraint/headrest that may be inte-
grated, adjustable or non-adjustable.
.Adjustable head restraints/headrests
have multiple notches along the stalk to
lock them in a desired adjustment posi-
tion..The non-adjustable head restraints/
headrests have a single locking notch to
secure them to the seat frame.
.Proper Adjustment:
— For the adjustable type, align the head
restraint/headrest so the center of
your ear is approximately level with
the center of the head restraint/
headrest.
— If your ear position is still higher than
the recommended alignment, place
the head restraint/headrest at the
highest position.
.If the head restraint/headrest has been
removed, ensure that it is reinstalled and
locked in place before riding in that
designated seating position.
SSS0992
ADJUSTABLE HEAD RESTRAINT/
HEADREST COMPONENTS
1. Removable head restraint/headrest
2. Multiple notches
3. Lock knob
4. Stalks

JVR0203X
NON-ADJUSTABLE HEAD RE-
STRAINT/HEADREST COMPO-
NENTS
1. Removable head restraint/headrest
2. Single notch
3. Lock knob
4. Stalks
SSS1037
REMOVE
Use the following procedure to remove the
head restraint/headrest.
1. Pull the head restraint/headrest up to
the highest position.
2. Push and hold the lock knob.
3. Remove the head restraint/headrest
from the seat.
4. Store the head restraint/headrest prop-
erly in a secure place so it is not loose in
the vehicle.
5. Reinstall and properly adjust the head
restraint/headrest before an occupant
uses the seating position.
SSS1038
INSTALL
1. Align the head restraint/headrest stalks
with the holes in the seat. Make sure that
the head restraint/headrest is facing the
correct direction. The stalk with the
adjustment notch
must be installed in
the hole with the lock knob.
2. Push and hold the lock knob and push the
head restraint/headrest down.
3. Properly adjust the head restraint/head-
rest before an occupant uses the seating
position.
Safety — Seats, seat belts and supplemental restraint system1-9

1-12Safety — Seats, seat belts and supplemental restraint system
SSS0016
SSS0014
WARNING
.Every person who drives or rides in
this vehicle should use a seat belt at
all times. Children should be properly
restrained in the rear seat and, if
appropriate, in a child restraint.
.The seat belt should be properly
adjusted to a snug fit. Failure to do
so may reduce the effectiveness of
the entire restraint system and in-
crease the chance or severity of injury
in an accident. Serious injury or death
can occur if the seat belt is not worn
properly.
.Always route the shoulder belt over
your shoulder and across your chest.
Never run the belt behind your back,
under your arm or across your neck.
The belt should be away from your
face and neck, but not falling off your
shoulder.
.Position the lap belt as low and snug
as possible AROUND THE HIPS, NOT
THE WAIST. A lap belt worn too high
could increase the risk of internal
injuries in an accident.
.Be sure the seat belt tongue is
securely fastened to the proper
buckle..Do not wear the seat belt inside out
or twisted. Doing so may reduce its
effectiveness.
.Do not allow more than one person to
use the same seat belt.
.Never carry more people in the ve-
hicle than there are seat belts.
.If the seat belt warning light glows
continuously while the ignition is
turned ON with all doors closed and
all seat belts fastened, it may indicate
a malfunction in the system. Have the
system checked. It is recommended
you visit an INFINITI retailer for this
service.
.No changes should be made to the
seat belt system. For example, do not
modify the seat belt, add material or
install devices that may change the
seat belt routing or tension. Doing so
may affect the operation of the seat
belt system. Modifying or tampering
with the seat belt system may result
in serious personal injury.
.Once a seat belt pretensioner has
activated, it cannot be reused and
must be replaced together with the
retractor. It is recommended you visit
an INFINITI retailer for this service.

.All seat belt assemblies, including
retractors and attaching hardware,
should be inspected after any colli-
sion. It is recommended you visit an
INFINITI retailer for this service.
INFINITI recommends that all seat
belt assemblies in use during a colli-
sion be replaced unless the collision
was minor and the belts show no
damage and continue to operate
properly. Seat belt assemblies not in
use during a collision should also be
inspected and replaced if either da-
mage or improper operation is noted.
.All child restraints and attaching
hardware should be inspected after
any collision. Always follow the re-
straint manufacturer’s inspection in-
structions and replacement
recommendations. The child re-
straints should be replaced if they
are damaged.
JVR0575X
SEAT BELT WARNING LIGHT
AND CHIME
The driver and front passenger seats are
equipped with an enhanced seat belt remin-
der function. If your vehicle is equipped with
an enhanced seat belt reminder function, a
visual and audible alert will operate if a
driver or front passenger seat belt is un-
buckled at speeds of approximately 10 MPH
(15 km/h) or more under the following
conditions:
.If the driver seat belt is not fastened.
.The front passenger’s seat belt is not
fastened and the seat is occupied by a
passenger for 7 seconds after the igni-tion switch is placed in the ON position.
.The front passenger’s seat belt is not
fastened and objects or external force on
the passenger seat change the seat belt
reminder classification to “occupied”.
The seat belt warning light will flash under
the conditions shown above until the neces-
sary seat belt is securely fastened.
A warning chime will sound for approxi-
mately 95 seconds or until one of the
following conditions is met:
.The unbuckled front passenger’s seat
belt is securely fastened.
.The seat belt reminder function in the
front passenger seat no longer detects
that the front passenger seat is occu-
pied.
.The ignition switch is turned off.
The below situations could result in the seat
belt warning light being illuminated and the
chime sounding, even with no occupant
present in the passenger seat:
.Heavy objects placed on the seat.
.Someone pushing or pulling on the front
passenger seat.
.An object placed under the front passen-
ger seat.
.An object placed between the seat
cushion and center console or between
the seat cushion and the door.
Safety — Seats, seat belts and supplemental restraint system1-13

1-16Safety — Seats, seat belts and supplemental restraint system
The Automatic Locking Retractor (ALR)
mode (child restraint mode) locks the seat
belt for child restraint installation.
When the ALR mode is activated the seat
belt cannot be extended again until the seat
belt tongue is detached from the buckle and
fully retracted. The seat belt returns to the
ELR mode after the seat belt fully retracts.
For additional information, see “Child re-
straints” (P.1-20).
The ALR mode should be used only for child
restraint installation. During normal seat
belt use by an occupant, the ALR mode
should not be activated. If it is activated, it
may cause uncomfortable seat belt tension.
WARNING
When fastening the seat belts, be certain
that seatbacks are completely secured in
the latched position. If they are not
completely secured, passengers may be
injured in an accident or sudden stop.
SSS0326
Unfastening the seat belts
To unfasten the seat belt, push the button
on the buckle. The seat belt automatically
retracts.
Checking seat belt operation
Seat belt retractors are designed to lock seat
belt movement by two separate methods:
.When the belt is pulled quickly from the
retractor.
.When the vehicle slows down rapidly.
To increase your confidence in the seat belts,
check the operation as follows:
.Grasp the shoulder belt and pull forward
quickly. The retractor should lock andrestrict further belt movement.
If the retractor does not lock during this
check, get the system checked. It is recom-
mended you visit an INFINITI retailer for this
service, or to learn more about seat belt
operation.